u-boot/arch/arm/dts/sun50i-h6-orangepi-lite2.dts
Andre Przywara 7f53f5093b sunxi: dts: arm64: update devicetree files
Update the devicetree files from the Linux kernel, version v6.0-rc4.
This is covering the 64-bit SoCs, from arch/arm64/boot/dts/allwinner.

This avoids the not backwards-compatible r_intc binding change, to allow
older kernels to boot, but the other nodes are updated.

Not much change here, the vast majority is actually cosmetic: node names
and using symbolic names for the the RTC clocks.
Some A64 boards gain some audio nodes.
The H616 DTs are now switched to the version finally merged into the
kernel, which brings some changes, but none affecting U-Boot.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
2022-10-18 08:15:59 +01:00

74 lines
1.7 KiB
Text

// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
// Copyright (C) 2018 Jagan Teki <jagan@openedev.com>
#include "sun50i-h6-orangepi.dtsi"
/ {
model = "OrangePi Lite2";
compatible = "xunlong,orangepi-lite2", "allwinner,sun50i-h6";
aliases {
serial1 = &uart1; /* BT-UART */
};
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
clocks = <&rtc CLK_OSC32K_FANOUT>;
clock-names = "ext_clock";
reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PM3 */
post-power-on-delay-ms = <200>;
};
};
&mmc1 {
vmmc-supply = <&reg_cldo2>;
vqmmc-supply = <&reg_bldo3>;
mmc-pwrseq = <&wifi_pwrseq>;
bus-width = <4>;
non-removable;
status = "okay";
brcm: sdio-wifi@1 {
reg = <1>;
compatible = "brcm,bcm4329-fmac";
interrupt-parent = <&r_pio>;
interrupts = <1 0 IRQ_TYPE_LEVEL_LOW>; /* PM0 */
interrupt-names = "host-wake";
};
};
&reg_cldo2 {
/*
* This regulator is connected with CLDO3.
* Before the kernel can support synchronized
* enable of coupled regulators, keep them
* both always on as a ugly hack.
*/
regulator-always-on;
};
&reg_cldo3 {
/*
* This regulator is connected with CLDO2.
* See the comments for CLDO2.
*/
regulator-always-on;
};
/* There's the BT part of the AP6255 connected to that UART */
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
uart-has-rtscts;
status = "okay";
bluetooth {
compatible = "brcm,bcm4345c5";
clocks = <&rtc CLK_OSC32K_FANOUT>;
clock-names = "lpo";
device-wakeup-gpios = <&r_pio 1 2 GPIO_ACTIVE_HIGH>; /* PM2 */
host-wakeup-gpios = <&r_pio 1 1 GPIO_ACTIVE_HIGH>; /* PM1 */
shutdown-gpios = <&r_pio 1 4 GPIO_ACTIVE_HIGH>; /* PM4 */
max-speed = <1500000>;
};
};