u-boot/arch/arm/mach-exynos/exynos5_setup.h
Tom Rini 83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00

946 lines
25 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Machine Specific Values for SMDK5250 board based on EXYNOS5
*
* Copyright (C) 2012 Samsung Electronics
*/
#ifndef _SMDK5250_SETUP_H
#define _SMDK5250_SETUP_H
#include <config.h>
#include <asm/arch/dmc.h>
#define NOT_AVAILABLE 0
#define DATA_MASK 0xFFFFF
#define ENABLE_BIT 0x1
#define DISABLE_BIT 0x0
#define CA_SWAP_EN (1 << 0)
/* Set PLL */
#define set_pll(mdiv, pdiv, sdiv) (1<<31 | mdiv<<16 | pdiv<<8 | sdiv)
/* MEMCONTROL register bit fields */
#define DMC_MEMCONTROL_CLK_STOP_DISABLE (0 << 0)
#define DMC_MEMCONTROL_DPWRDN_DISABLE (0 << 1)
#define DMC_MEMCONTROL_DPWRDN_ACTIVE_PRECHARGE (0 << 2)
#define DMC_MEMCONTROL_TP_DISABLE (0 << 4)
#define DMC_MEMCONTROL_DSREF_DISABLE (0 << 5)
#define DMC_MEMCONTROL_DSREF_ENABLE (1 << 5)
#define DMC_MEMCONTROL_ADD_LAT_PALL_CYCLE(x) (x << 6)
#define DMC_MEMCONTROL_MEM_TYPE_LPDDR3 (7 << 8)
#define DMC_MEMCONTROL_MEM_TYPE_DDR3 (6 << 8)
#define DMC_MEMCONTROL_MEM_TYPE_LPDDR2 (5 << 8)
#define DMC_MEMCONTROL_MEM_WIDTH_32BIT (2 << 12)
#define DMC_MEMCONTROL_NUM_CHIP_1 (0 << 16)
#define DMC_MEMCONTROL_NUM_CHIP_2 (1 << 16)
#define DMC_MEMCONTROL_BL_8 (3 << 20)
#define DMC_MEMCONTROL_BL_4 (2 << 20)
#define DMC_MEMCONTROL_PZQ_DISABLE (0 << 24)
#define DMC_MEMCONTROL_MRR_BYTE_7_0 (0 << 25)
#define DMC_MEMCONTROL_MRR_BYTE_15_8 (1 << 25)
#define DMC_MEMCONTROL_MRR_BYTE_23_16 (2 << 25)
#define DMC_MEMCONTROL_MRR_BYTE_31_24 (3 << 25)
/* MEMCONFIG0 register bit fields */
#define DMC_MEMCONFIGX_CHIP_MAP_INTERLEAVED (1 << 12)
#define DMC_MEMCONFIG_CHIP_MAP_SPLIT (2 << 12)
#define DMC_MEMCONFIGX_CHIP_COL_10 (3 << 8)
#define DMC_MEMCONFIGX_CHIP_ROW_14 (2 << 4)
#define DMC_MEMCONFIGX_CHIP_ROW_15 (3 << 4)
#define DMC_MEMCONFIGX_CHIP_BANK_8 (3 << 0)
#define DMC_MEMBASECONFIGX_CHIP_BASE(x) (x << 16)
#define DMC_MEMBASECONFIGX_CHIP_MASK(x) (x << 0)
#define DMC_MEMBASECONFIG_VAL(x) ( \
DMC_MEMBASECONFIGX_CHIP_BASE(x) | \
DMC_MEMBASECONFIGX_CHIP_MASK(0x780) \
)
/*
* As we use channel interleaving, therefore value of the base address
* register must be set as half of the bus base address
* RAM start addess is 0x2000_0000 which means chip_base is 0x20, so
* we need to set half 0x10 to the membaseconfigx registers
* see exynos5420 UM section 17.17.3.21 for more.
*/
#define DMC_CHIP_BASE_0 0x10
#define DMC_CHIP_BASE_1 0x50
#define DMC_CHIP_MASK 0x7C0
#define DMC_MEMBASECONFIG0_VAL DMC_MEMBASECONFIG_VAL(0x40)
#define DMC_MEMBASECONFIG1_VAL DMC_MEMBASECONFIG_VAL(0x80)
#define DMC_PRECHCONFIG_VAL 0xFF000000
#define DMC_PWRDNCONFIG_VAL 0xFFFF00FF
#define DMC_CONCONTROL_RESET_VAL 0x0FFF0000
#define DFI_INIT_START (1 << 28)
#define EMPTY (1 << 8)
#define AREF_EN (1 << 5)
#define DFI_INIT_COMPLETE_CHO (1 << 2)
#define DFI_INIT_COMPLETE_CH1 (1 << 3)
#define RDLVL_COMPLETE_CHO (1 << 14)
#define RDLVL_COMPLETE_CH1 (1 << 15)
#define CLK_STOP_EN (1 << 0)
#define DPWRDN_EN (1 << 1)
#define DSREF_EN (1 << 5)
/* COJCONTROL register bit fields */
#define DMC_CONCONTROL_IO_PD_CON_DISABLE (0 << 3)
#define DMC_CONCONTROL_IO_PD_CON_ENABLE (1 << 3)
#define DMC_CONCONTROL_AREF_EN_DISABLE (0 << 5)
#define DMC_CONCONTROL_AREF_EN_ENABLE (1 << 5)
#define DMC_CONCONTROL_EMPTY_DISABLE (0 << 8)
#define DMC_CONCONTROL_EMPTY_ENABLE (1 << 8)
#define DMC_CONCONTROL_RD_FETCH_DISABLE (0x0 << 12)
#define DMC_CONCONTROL_TIMEOUT_LEVEL0 (0xFFF << 16)
#define DMC_CONCONTROL_DFI_INIT_START_DISABLE (0 << 28)
#define DMC_CONCONTROL_VAL 0x1FFF2101
#define DREX_CONCONTROL_VAL DMC_CONCONTROL_VAL \
| DMC_CONCONTROL_AREF_EN_ENABLE \
| DMC_CONCONTROL_IO_PD_CON_ENABLE
#define DMC_CONCONTROL_IO_PD_CON(x) (x << 6)
/* CLK_DIV_CPU1 */
#define HPM_RATIO 0x2
#define COPY_RATIO 0x0
/* CLK_DIV_CPU1 = 0x00000003 */
#define CLK_DIV_CPU1_VAL ((HPM_RATIO << 4) \
| (COPY_RATIO))
/* CLK_SRC_CORE0 */
#define CLK_SRC_CORE0_VAL 0x00000000
/* CLK_SRC_CORE1 */
#define CLK_SRC_CORE1_VAL 0x100
/* CLK_DIV_CORE0 */
#define CLK_DIV_CORE0_VAL 0x00120000
/* CLK_DIV_CORE1 */
#define CLK_DIV_CORE1_VAL 0x07070700
/* CLK_DIV_SYSRGT */
#define CLK_DIV_SYSRGT_VAL 0x00000111
/* CLK_DIV_ACP */
#define CLK_DIV_ACP_VAL 0x12
/* CLK_DIV_SYSLFT */
#define CLK_DIV_SYSLFT_VAL 0x00000311
#define MUX_APLL_SEL_MASK (1 << 0)
#define MUX_MPLL_SEL_MASK (1 << 8)
#define MPLL_SEL_MOUT_MPLLFOUT (2 << 8)
#define MUX_CPLL_SEL_MASK (1 << 8)
#define MUX_EPLL_SEL_MASK (1 << 12)
#define MUX_VPLL_SEL_MASK (1 << 16)
#define MUX_GPLL_SEL_MASK (1 << 28)
#define MUX_BPLL_SEL_MASK (1 << 0)
#define MUX_HPM_SEL_MASK (1 << 20)
#define HPM_SEL_SCLK_MPLL (1 << 21)
#define PLL_LOCKED (1 << 29)
#define APLL_CON0_LOCKED (1 << 29)
#define MPLL_CON0_LOCKED (1 << 29)
#define BPLL_CON0_LOCKED (1 << 29)
#define CPLL_CON0_LOCKED (1 << 29)
#define EPLL_CON0_LOCKED (1 << 29)
#define GPLL_CON0_LOCKED (1 << 29)
#define VPLL_CON0_LOCKED (1 << 29)
#define CLK_REG_DISABLE 0x0
#define TOP2_VAL 0x0110000
/* SCLK_SRC_ISP - set SPI0/1 to 6 = SCLK_MPLL_USER */
#define SPI0_ISP_SEL 6
#define SPI1_ISP_SEL 6
#define SCLK_SRC_ISP_VAL (SPI1_ISP_SEL << 4) \
| (SPI0_ISP_SEL << 0)
/* SCLK_DIV_ISP - set SPI0/1 to 0xf = divide by 16 */
#define SPI0_ISP_RATIO 0xf
#define SPI1_ISP_RATIO 0xf
#define SCLK_DIV_ISP_VAL (SPI1_ISP_RATIO << 12) \
| (SPI0_ISP_RATIO << 0)
/* CLK_DIV_FSYS2 */
#define MMC2_RATIO_MASK 0xf
#define MMC2_RATIO_VAL 0x3
#define MMC2_RATIO_OFFSET 0
#define MMC2_PRE_RATIO_MASK 0xff
#define MMC2_PRE_RATIO_VAL 0x9
#define MMC2_PRE_RATIO_OFFSET 8
#define MMC3_RATIO_MASK 0xf
#define MMC3_RATIO_VAL 0x1
#define MMC3_RATIO_OFFSET 16
#define MMC3_PRE_RATIO_MASK 0xff
#define MMC3_PRE_RATIO_VAL 0x0
#define MMC3_PRE_RATIO_OFFSET 24
/* CLK_SRC_LEX */
#define CLK_SRC_LEX_VAL 0x0
/* CLK_DIV_LEX */
#define CLK_DIV_LEX_VAL 0x10
/* CLK_DIV_R0X */
#define CLK_DIV_R0X_VAL 0x10
/* CLK_DIV_L0X */
#define CLK_DIV_R1X_VAL 0x10
/* CLK_DIV_ISP2 */
#define CLK_DIV_ISP2_VAL 0x1
/* CLK_SRC_KFC */
#define SRC_KFC_HPM_SEL (1 << 15)
/* CLK_SRC_KFC */
#define CLK_SRC_KFC_VAL 0x00008001
/* CLK_DIV_KFC */
#define CLK_DIV_KFC_VAL 0x03300110
/* CLK_DIV2_RATIO */
#define CLK_DIV2_RATIO 0x10111150
/* CLK_DIV4_RATIO */
#define CLK_DIV4_RATIO 0x00000003
/* CLK_DIV_G2D */
#define CLK_DIV_G2D 0x00000010
/*
* DIV_DISP1_0
* For DP, divisor should be 2
*/
#define CLK_DIV_DISP1_0_FIMD1 (2 << 0)
/* CLK_GATE_IP_DISP1 */
#define CLK_GATE_DP1_ALLOW (1 << 4)
/* AUDIO CLK SEL */
#define AUDIO0_SEL_EPLL (0x6 << 28)
#define AUDIO0_RATIO 0x5
#define PCM0_RATIO 0x3
#define DIV_MAU_VAL (PCM0_RATIO << 24 | AUDIO0_RATIO << 20)
/* CLK_SRC_CDREX */
#define MUX_MCLK_CDR_MSPLL (1 << 4)
#define MUX_BPLL_SEL_FOUTBPLL (1 << 0)
#define BPLL_SEL_MASK 0x7
#define FOUTBPLL 2
#define DDR3PHY_CTRL_PHY_RESET (1 << 0)
#define DDR3PHY_CTRL_PHY_RESET_OFF (0 << 0)
#define PHY_CON0_RESET_VAL 0x17020a40
#define P0_CMD_EN (1 << 14)
#define BYTE_RDLVL_EN (1 << 13)
#define CTRL_SHGATE (1 << 8)
#define PHY_CON1_RESET_VAL 0x09210100
#define RDLVL_PASS_ADJ_VAL 0x6
#define RDLVL_PASS_ADJ_OFFSET 16
#define CTRL_GATEDURADJ_MASK (0xf << 20)
#define READ_LEVELLING_DDR3 0x0100
#define PHY_CON2_RESET_VAL 0x00010004
#define INIT_DESKEW_EN (1 << 6)
#define DLL_DESKEW_EN (1 << 12)
#define RDLVL_GATE_EN (1 << 24)
#define RDLVL_EN (1 << 25)
#define RDLVL_INCR_ADJ (0x1 << 16)
/* DREX_PAUSE */
#define DREX_PAUSE_EN (1 << 0)
#define BYPASS_EN (1 << 22)
/* MEMMORY VAL */
#define PHY_CON0_VAL 0x17021A00
#define PHY_CON12_RESET_VAL 0x10100070
#define PHY_CON12_VAL 0x10107F50
#define CTRL_START (1 << 6)
#define CTRL_DLL_ON (1 << 5)
#define CTRL_LOCK_COARSE_OFFSET 10
#define CTRL_LOCK_COARSE_MASK (0x7F << CTRL_LOCK_COARSE_OFFSET)
#define CTRL_LOCK_COARSE(x) (((x) & CTRL_LOCK_COARSE_MASK) >> \
CTRL_LOCK_COARSE_OFFSET)
#define CTRL_FORCE_MASK (0x7F << 8)
#define CTRL_FINE_LOCKED 0x7
#define CTRL_OFFSETD_RESET_VAL 0x8
#define CTRL_OFFSETD_VAL 0x7F
#define CTRL_OFFSETR0 0x7F
#define CTRL_OFFSETR1 0x7F
#define CTRL_OFFSETR2 0x7F
#define CTRL_OFFSETR3 0x7F
#define PHY_CON4_VAL (CTRL_OFFSETR0 << 0 | \
CTRL_OFFSETR1 << 8 | \
CTRL_OFFSETR2 << 16 | \
CTRL_OFFSETR3 << 24)
#define PHY_CON4_RESET_VAL 0x08080808
#define CTRL_OFFSETW0 0x7F
#define CTRL_OFFSETW1 0x7F
#define CTRL_OFFSETW2 0x7F
#define CTRL_OFFSETW3 0x7F
#define PHY_CON6_VAL (CTRL_OFFSETW0 << 0 | \
CTRL_OFFSETW1 << 8 | \
CTRL_OFFSETW2 << 16 | \
CTRL_OFFSETW3 << 24)
#define PHY_CON6_RESET_VAL 0x08080808
#define PHY_CON14_RESET_VAL 0x001F0000
#define CTRL_PULLD_DQS 0xF
#define CTRL_PULLD_DQS_OFFSET 0
/* ZQ Configurations */
#define PHY_CON16_RESET_VAL 0x08000304
#define ZQ_CLK_EN (1 << 27)
#define ZQ_CLK_DIV_EN (1 << 18)
#define ZQ_MANUAL_STR (1 << 1)
#define ZQ_DONE (1 << 0)
#define ZQ_MODE_DDS_OFFSET 24
#define CTRL_RDLVL_GATE_ENABLE 1
#define CTRL_RDLVL_GATE_DISABLE 0
#define CTRL_RDLVL_DATA_ENABLE 2
/* Direct Command */
#define DIRECT_CMD_NOP 0x07000000
#define DIRECT_CMD_PALL 0x01000000
#define DIRECT_CMD_ZQINIT 0x0a000000
#define DIRECT_CMD_CHANNEL_SHIFT 28
#define DIRECT_CMD_CHIP_SHIFT 20
#define DIRECT_CMD_BANK_SHIFT 16
#define DIRECT_CMD_REFA (5 << 24)
#define DIRECT_CMD_MRS1 0x71C00
#define DIRECT_CMD_MRS2 0x10BFC
#define DIRECT_CMD_MRS3 0x0050C
#define DIRECT_CMD_MRS4 0x00868
#define DIRECT_CMD_MRS5 0x00C04
/* Drive Strength */
#define IMPEDANCE_48_OHM 4
#define IMPEDANCE_40_OHM 5
#define IMPEDANCE_34_OHM 6
#define IMPEDANCE_30_OHM 7
#define PHY_CON39_VAL_48_OHM 0x09240924
#define PHY_CON39_VAL_40_OHM 0x0B6D0B6D
#define PHY_CON39_VAL_34_OHM 0x0DB60DB6
#define PHY_CON39_VAL_30_OHM 0x0FFF0FFF
#define CTRL_BSTLEN_OFFSET 8
#define CTRL_RDLAT_OFFSET 0
#define CMD_DEFAULT_LPDDR3 0xF
#define CMD_DEFUALT_OFFSET 0
#define T_WRDATA_EN 0x7
#define T_WRDATA_EN_DDR3 0x8
#define T_WRDATA_EN_OFFSET 16
#define T_WRDATA_EN_MASK 0x1f
#define PHY_CON31_VAL 0x0C183060
#define PHY_CON32_VAL 0x60C18306
#define PHY_CON33_VAL 0x00000030
#define PHY_CON31_RESET_VAL 0x0
#define PHY_CON32_RESET_VAL 0x0
#define PHY_CON33_RESET_VAL 0x0
#define SL_DLL_DYN_CON_EN (1 << 1)
#define FP_RESYNC (1 << 3)
#define CTRL_START (1 << 6)
#define DMC_AREF_EN (1 << 5)
#define DMC_CONCONTROL_EMPTY (1 << 8)
#define DFI_INIT_START (1 << 28)
#define DMC_MEMCONTROL_VAL 0x00312700
#define CLK_STOP_EN (1 << 0)
#define DPWRDN_EN (1 << 1)
#define DSREF_EN (1 << 5)
#define MEMBASECONFIG_CHIP_MASK_VAL 0x7E0
#define MEMBASECONFIG_CHIP_MASK_OFFSET 0
#define MEMBASECONFIG0_CHIP_BASE_VAL 0x20
#define MEMBASECONFIG1_CHIP_BASE_VAL 0x40
#define CHIP_BASE_OFFSET 16
#define MEMCONFIG_VAL 0x1323
#define PRECHCONFIG_DEFAULT_VAL 0xFF000000
#define PWRDNCONFIG_DEFAULT_VAL 0xFFFF00FF
#define TIMINGAREF_VAL 0x5d
#define TIMINGROW_VAL 0x345A8692
#define TIMINGDATA_VAL 0x3630065C
#define TIMINGPOWER_VAL 0x50380336
#define DFI_INIT_COMPLETE (1 << 3)
#define BRBRSVCONTROL_VAL 0x00000033
#define BRBRSVCONFIG_VAL 0x88778877
/* Clock Gating Control (CGCONTROL) register */
#define MEMIF_CG_EN (1 << 3) /* Memory interface clock gating */
#define SCG_CG_EN (1 << 2) /* Scheduler clock gating */
#define BUSIF_WR_CG_EN (1 << 1) /* Bus interface write channel clock gating */
#define BUSIF_RD_CG_EN (1 << 0) /* Bus interface read channel clock gating */
#define DMC_INTERNAL_CG (MEMIF_CG_EN | SCG_CG_EN | \
BUSIF_WR_CG_EN | BUSIF_RD_CG_EN)
/* DMC PHY Control0 register */
#define PHY_CONTROL0_RESET_VAL 0x0
#define MEM_TERM_EN (1 << 31) /* Termination enable for memory */
#define PHY_TERM_EN (1 << 30) /* Termination enable for PHY */
#define DMC_CTRL_SHGATE (1 << 29) /* Duration of DQS gating signal */
#define FP_RSYNC (1 << 3) /* Force DLL resyncronization */
/* Driver strength for CK, CKE, CS & CA */
#define IMP_OUTPUT_DRV_40_OHM 0x5
#define IMP_OUTPUT_DRV_30_OHM 0x7
#define DA_3_DS_OFFSET 25
#define DA_2_DS_OFFSET 22
#define DA_1_DS_OFFSET 19
#define DA_0_DS_OFFSET 16
#define CA_CK_DRVR_DS_OFFSET 9
#define CA_CKE_DRVR_DS_OFFSET 6
#define CA_CS_DRVR_DS_OFFSET 3
#define CA_ADR_DRVR_DS_OFFSET 0
#define PHY_CON42_CTRL_BSTLEN_SHIFT 8
#define PHY_CON42_CTRL_RDLAT_SHIFT 0
/*
* Definitions that differ with SoC's.
* Below is the part defining macros for Exynos5250.
* Else part introduces macros for Exynos5420.
*/
#ifndef CONFIG_EXYNOS5420
/* APLL_CON1 */
#define APLL_CON1_VAL (0x00203800)
/* MPLL_CON1 */
#define MPLL_CON1_VAL (0x00203800)
/* CPLL_CON1 */
#define CPLL_CON1_VAL (0x00203800)
/* DPLL_CON1 */
#define DPLL_CON1_VAL (NOT_AVAILABLE)
/* GPLL_CON1 */
#define GPLL_CON1_VAL (0x00203800)
/* EPLL_CON1, CON2 */
#define EPLL_CON1_VAL 0x00000000
#define EPLL_CON2_VAL 0x00000080
/* VPLL_CON1, CON2 */
#define VPLL_CON1_VAL 0x00000000
#define VPLL_CON2_VAL 0x00000080
/* RPLL_CON1, CON2 */
#define RPLL_CON1_VAL NOT_AVAILABLE
#define RPLL_CON2_VAL NOT_AVAILABLE
/* BPLL_CON1 */
#define BPLL_CON1_VAL 0x00203800
/* SPLL_CON1 */
#define SPLL_CON1_VAL NOT_AVAILABLE
/* IPLL_CON1 */
#define IPLL_CON1_VAL NOT_AVAILABLE
/* KPLL_CON1 */
#define KPLL_CON1_VAL NOT_AVAILABLE
/* CLK_SRC_ISP */
#define CLK_SRC_ISP_VAL NOT_AVAILABLE
#define CLK_DIV_ISP0_VAL 0x31
#define CLK_DIV_ISP1_VAL 0x0
/* CLK_FSYS */
#define CLK_SRC_FSYS0_VAL 0x66666
#define CLK_DIV_FSYS0_VAL 0x0BB00000
#define CLK_DIV_FSYS1_VAL NOT_AVAILABLE
#define CLK_DIV_FSYS2_VAL NOT_AVAILABLE
/* CLK_SRC_CPU */
/* 0 = MOUTAPLL, 1 = SCLKMPLL */
#define MUX_HPM_SEL 0
#define MUX_CPU_SEL 0
#define MUX_APLL_SEL 1
#define CLK_SRC_CPU_VAL ((MUX_HPM_SEL << 20) \
| (MUX_CPU_SEL << 16) \
| (MUX_APLL_SEL))
/* CLK_SRC_CDREX */
#define CLK_SRC_CDREX_VAL 0x1
/* CLK_DIV_CDREX */
#define CLK_DIV_CDREX0_VAL NOT_AVAILABLE
#define CLK_DIV_CDREX1_VAL NOT_AVAILABLE
/* CLK_DIV_CPU0_VAL */
#define CLK_DIV_CPU0_VAL NOT_AVAILABLE
#define MCLK_CDREX2_RATIO 0x0
#define ACLK_EFCON_RATIO 0x1
#define MCLK_DPHY_RATIO 0x1
#define MCLK_CDREX_RATIO 0x1
#define ACLK_C2C_200_RATIO 0x1
#define C2C_CLK_400_RATIO 0x1
#define PCLK_CDREX_RATIO 0x1
#define ACLK_CDREX_RATIO 0x1
#define CLK_DIV_CDREX_VAL ((MCLK_DPHY_RATIO << 24) \
| (C2C_CLK_400_RATIO << 6) \
| (PCLK_CDREX_RATIO << 4) \
| (ACLK_CDREX_RATIO))
/* CLK_SRC_TOP0 */
#define MUX_ACLK_300_GSCL_SEL 0x0
#define MUX_ACLK_300_GSCL_MID_SEL 0x0
#define MUX_ACLK_400_G3D_MID_SEL 0x0
#define MUX_ACLK_333_SEL 0x0
#define MUX_ACLK_300_DISP1_SEL 0x0
#define MUX_ACLK_300_DISP1_MID_SEL 0x0
#define MUX_ACLK_200_SEL 0x0
#define MUX_ACLK_166_SEL 0x0
#define CLK_SRC_TOP0_VAL ((MUX_ACLK_300_GSCL_SEL << 25) \
| (MUX_ACLK_300_GSCL_MID_SEL << 24) \
| (MUX_ACLK_400_G3D_MID_SEL << 20) \
| (MUX_ACLK_333_SEL << 16) \
| (MUX_ACLK_300_DISP1_SEL << 15) \
| (MUX_ACLK_300_DISP1_MID_SEL << 14) \
| (MUX_ACLK_200_SEL << 12) \
| (MUX_ACLK_166_SEL << 8))
/* CLK_SRC_TOP1 */
#define MUX_ACLK_400_G3D_SEL 0x1
#define MUX_ACLK_400_ISP_SEL 0x0
#define MUX_ACLK_400_IOP_SEL 0x0
#define MUX_ACLK_MIPI_HSI_TXBASE_SEL 0x0
#define MUX_ACLK_300_GSCL_MID1_SEL 0x0
#define MUX_ACLK_300_DISP1_MID1_SEL 0x0
#define CLK_SRC_TOP1_VAL ((MUX_ACLK_400_G3D_SEL << 28) \
|(MUX_ACLK_400_ISP_SEL << 24) \
|(MUX_ACLK_400_IOP_SEL << 20) \
|(MUX_ACLK_MIPI_HSI_TXBASE_SEL << 16) \
|(MUX_ACLK_300_GSCL_MID1_SEL << 12) \
|(MUX_ACLK_300_DISP1_MID1_SEL << 8))
/* CLK_SRC_TOP2 */
#define MUX_GPLL_SEL 0x1
#define MUX_BPLL_USER_SEL 0x0
#define MUX_MPLL_USER_SEL 0x0
#define MUX_VPLL_SEL 0x1
#define MUX_EPLL_SEL 0x1
#define MUX_CPLL_SEL 0x1
#define VPLLSRC_SEL 0x0
#define CLK_SRC_TOP2_VAL ((MUX_GPLL_SEL << 28) \
| (MUX_BPLL_USER_SEL << 24) \
| (MUX_MPLL_USER_SEL << 20) \
| (MUX_VPLL_SEL << 16) \
| (MUX_EPLL_SEL << 12) \
| (MUX_CPLL_SEL << 8) \
| (VPLLSRC_SEL))
/* CLK_SRC_TOP3 */
#define MUX_ACLK_333_SUB_SEL 0x1
#define MUX_ACLK_400_SUB_SEL 0x1
#define MUX_ACLK_266_ISP_SUB_SEL 0x1
#define MUX_ACLK_266_GPS_SUB_SEL 0x0
#define MUX_ACLK_300_GSCL_SUB_SEL 0x1
#define MUX_ACLK_266_GSCL_SUB_SEL 0x1
#define MUX_ACLK_300_DISP1_SUB_SEL 0x1
#define MUX_ACLK_200_DISP1_SUB_SEL 0x1
#define CLK_SRC_TOP3_VAL ((MUX_ACLK_333_SUB_SEL << 24) \
| (MUX_ACLK_400_SUB_SEL << 20) \
| (MUX_ACLK_266_ISP_SUB_SEL << 16) \
| (MUX_ACLK_266_GPS_SUB_SEL << 12) \
| (MUX_ACLK_300_GSCL_SUB_SEL << 10) \
| (MUX_ACLK_266_GSCL_SUB_SEL << 8) \
| (MUX_ACLK_300_DISP1_SUB_SEL << 6) \
| (MUX_ACLK_200_DISP1_SUB_SEL << 4))
#define CLK_SRC_TOP4_VAL NOT_AVAILABLE
#define CLK_SRC_TOP5_VAL NOT_AVAILABLE
#define CLK_SRC_TOP6_VAL NOT_AVAILABLE
#define CLK_SRC_TOP7_VAL NOT_AVAILABLE
/* CLK_DIV_TOP0 */
#define ACLK_300_DISP1_RATIO 0x2
#define ACLK_400_G3D_RATIO 0x0
#define ACLK_333_RATIO 0x0
#define ACLK_266_RATIO 0x2
#define ACLK_200_RATIO 0x3
#define ACLK_166_RATIO 0x1
#define ACLK_133_RATIO 0x1
#define ACLK_66_RATIO 0x5
#define CLK_DIV_TOP0_VAL ((ACLK_300_DISP1_RATIO << 28) \
| (ACLK_400_G3D_RATIO << 24) \
| (ACLK_333_RATIO << 20) \
| (ACLK_266_RATIO << 16) \
| (ACLK_200_RATIO << 12) \
| (ACLK_166_RATIO << 8) \
| (ACLK_133_RATIO << 4) \
| (ACLK_66_RATIO))
/* CLK_DIV_TOP1 */
#define ACLK_MIPI_HSI_TX_BASE_RATIO 0x3
#define ACLK_66_PRE_RATIO 0x1
#define ACLK_400_ISP_RATIO 0x1
#define ACLK_400_IOP_RATIO 0x1
#define ACLK_300_GSCL_RATIO 0x2
#define CLK_DIV_TOP1_VAL ((ACLK_MIPI_HSI_TX_BASE_RATIO << 28) \
| (ACLK_66_PRE_RATIO << 24) \
| (ACLK_400_ISP_RATIO << 20) \
| (ACLK_400_IOP_RATIO << 16) \
| (ACLK_300_GSCL_RATIO << 12))
#define CLK_DIV_TOP2_VAL NOT_AVAILABLE
/* PLL Lock Value Factor */
#define PLL_LOCK_FACTOR 250
#define PLL_X_LOCK_FACTOR 3000
/* CLK_SRC_PERIC0 */
#define PWM_SEL 6
#define UART3_SEL 6
#define UART2_SEL 6
#define UART1_SEL 6
#define UART0_SEL 6
/* SRC_CLOCK = SCLK_MPLL */
#define CLK_SRC_PERIC0_VAL ((PWM_SEL << 24) \
| (UART3_SEL << 12) \
| (UART2_SEL << 8) \
| (UART1_SEL << 4) \
| (UART0_SEL))
/* CLK_SRC_PERIC1 */
/* SRC_CLOCK = SCLK_MPLL */
#define SPI0_SEL 6
#define SPI1_SEL 6
#define SPI2_SEL 6
#define CLK_SRC_PERIC1_VAL ((SPI2_SEL << 24) \
| (SPI1_SEL << 20) \
| (SPI0_SEL << 16))
/* CLK_DIV_PERIL0 */
#define UART5_RATIO 7
#define UART4_RATIO 7
#define UART3_RATIO 7
#define UART2_RATIO 7
#define UART1_RATIO 7
#define UART0_RATIO 7
#define CLK_DIV_PERIC0_VAL ((UART3_RATIO << 12) \
| (UART2_RATIO << 8) \
| (UART1_RATIO << 4) \
| (UART0_RATIO))
/* CLK_DIV_PERIC1 */
#define SPI1_RATIO 0x7
#define SPI0_RATIO 0xf
#define SPI1_SUB_RATIO 0x0
#define SPI0_SUB_RATIO 0x0
#define CLK_DIV_PERIC1_VAL ((SPI1_SUB_RATIO << 24) \
| ((SPI1_RATIO << 16) \
| (SPI0_SUB_RATIO << 8) \
| (SPI0_RATIO << 0)))
/* CLK_DIV_PERIC2 */
#define SPI2_RATIO 0xf
#define SPI2_SUB_RATIO 0x0
#define CLK_DIV_PERIC2_VAL ((SPI2_SUB_RATIO << 8) \
| (SPI2_RATIO << 0))
/* CLK_DIV_PERIC3 */
#define PWM_RATIO 8
#define CLK_DIV_PERIC3_VAL (PWM_RATIO << 0)
/* CLK_DIV_PERIC4 */
#define CLK_DIV_PERIC4_VAL NOT_AVAILABLE
/* CLK_SRC_DISP1_0 */
#define CLK_SRC_DISP1_0_VAL 0x6
#define CLK_DIV_DISP1_0_VAL NOT_AVAILABLE
#define APLL_FOUT (1 << 0)
#define KPLL_FOUT NOT_AVAILABLE
#define CLK_DIV_CPERI1_VAL NOT_AVAILABLE
#else
#define CPU_CONFIG_STATUS_OFFSET 0x80
#define CPU_RST_FLAG_VAL 0xFCBA0D10
#define PAD_RETENTION_DRAM_COREBLK_VAL 0x10000000
/* APLL_CON1 */
#define APLL_CON1_VAL (0x0020F300)
/* MPLL_CON1 */
#define MPLL_CON1_VAL (0x0020F300)
/* CPLL_CON1 */
#define CPLL_CON1_VAL 0x0020f300
/* DPLL_CON1 */
#define DPLL_CON1_VAL (0x0020F300)
/* GPLL_CON1 */
#define GPLL_CON1_VAL (NOT_AVAILABLE)
/* EPLL_CON1, CON2 */
#define EPLL_CON1_VAL 0x00000000
#define EPLL_CON2_VAL 0x00000080
/* VPLL_CON1, CON2 */
#define VPLL_CON1_VAL 0x0020f300
#define VPLL_CON2_VAL NOT_AVAILABLE
/* RPLL_CON1, CON2 */
#define RPLL_CON1_VAL 0x00000000
#define RPLL_CON2_VAL 0x00000080
/* BPLL_CON1 */
#define BPLL_CON1_VAL 0x0020f300
/* SPLL_CON1 */
#define SPLL_CON1_VAL 0x0020f300
/* IPLL_CON1 */
#define IPLL_CON1_VAL 0x00000080
/* KPLL_CON1 */
#define KPLL_CON1_VAL 0x200000
/* CLK_SRC_ISP */
#define CLK_SRC_ISP_VAL 0x33366000
#define CLK_DIV_ISP0_VAL 0x13131300
#define CLK_DIV_ISP1_VAL 0xbb110202
/* CLK_FSYS */
#define CLK_SRC_FSYS0_VAL 0x33033300
#define CLK_DIV_FSYS0_VAL 0x0
#define CLK_DIV_FSYS1_VAL 0x04f13c4f
#define CLK_DIV_FSYS2_VAL 0x041d0000
/* CLK_SRC_CPU */
/* 0 = MOUTAPLL, 1 = SCLKMPLL */
#define MUX_HPM_SEL 1
#define MUX_CPU_SEL 0
#define MUX_APLL_SEL 1
#define CLK_SRC_CPU_VAL ((MUX_HPM_SEL << 20) \
| (MUX_CPU_SEL << 16) \
| (MUX_APLL_SEL))
/* CLK_SRC_CDREX */
#define CLK_SRC_CDREX_VAL 0x00000011
/* CLK_DIV_CDREX */
#define CLK_DIV_CDREX0_VAL 0x30010100
#define CLK_DIV_CDREX1_VAL 0x300
#define CLK_DIV_CDREX_VAL 0x17010100
/* CLK_DIV_CPU0_VAL */
#define CLK_DIV_CPU0_VAL 0x01440020
/* CLK_SRC_TOP */
#define CLK_SRC_TOP0_VAL 0x12221222
#define CLK_SRC_TOP1_VAL 0x00100200
#define CLK_SRC_TOP2_VAL 0x11101000
#define CLK_SRC_TOP3_VAL 0x11111111
#define CLK_SRC_TOP4_VAL 0x11110111
#define CLK_SRC_TOP5_VAL 0x11111101
#define CLK_SRC_TOP6_VAL 0x11110111
#define CLK_SRC_TOP7_VAL 0x00022200
/* CLK_DIV_TOP */
#define CLK_DIV_TOP0_VAL 0x23712311
#define CLK_DIV_TOP1_VAL 0x13100B00
#define CLK_DIV_TOP2_VAL 0x11101100
/* PLL Lock Value Factor */
#define PLL_LOCK_FACTOR 200
#define PLL_X_LOCK_FACTOR 3000
/* CLK_SRC_PERIC0 */
#define SPDIF_SEL 1
#define PWM_SEL 3
#define UART4_SEL 3
#define UART3_SEL 3
#define UART2_SEL 3
#define UART1_SEL 3
#define UART0_SEL 3
/* SRC_CLOCK = SCLK_RPLL */
#define CLK_SRC_PERIC0_VAL ((SPDIF_SEL << 28) \
| (PWM_SEL << 24) \
| (UART4_SEL << 20) \
| (UART3_SEL << 16) \
| (UART2_SEL << 12) \
| (UART1_SEL << 8) \
| (UART0_SEL << 4))
/* CLK_SRC_PERIC1 */
/* SRC_CLOCK = SCLK_EPLL */
#define SPI0_SEL 6
#define SPI1_SEL 6
#define SPI2_SEL 6
#define AUDIO0_SEL 6
#define AUDIO1_SEL 6
#define AUDIO2_SEL 6
#define CLK_SRC_PERIC1_VAL ((SPI2_SEL << 28) \
| (SPI1_SEL << 24) \
| (SPI0_SEL << 20) \
| (AUDIO2_SEL << 16) \
| (AUDIO2_SEL << 12) \
| (AUDIO2_SEL << 8))
/* CLK_DIV_PERIC0 */
#define PWM_RATIO 8
#define UART4_RATIO 9
#define UART3_RATIO 9
#define UART2_RATIO 9
#define UART1_RATIO 9
#define UART0_RATIO 9
#define CLK_DIV_PERIC0_VAL ((PWM_RATIO << 28) \
| (UART4_RATIO << 24) \
| (UART3_RATIO << 20) \
| (UART2_RATIO << 16) \
| (UART1_RATIO << 12) \
| (UART0_RATIO << 8))
/* CLK_DIV_PERIC1 */
#define SPI2_RATIO 0x1
#define SPI1_RATIO 0x1
#define SPI0_RATIO 0x1
#define CLK_DIV_PERIC1_VAL ((SPI2_RATIO << 28) \
| (SPI1_RATIO << 24) \
| (SPI0_RATIO << 20))
/* CLK_DIV_PERIC2 */
#define PCM2_RATIO 0x3
#define PCM1_RATIO 0x3
#define CLK_DIV_PERIC2_VAL ((PCM2_RATIO << 24) \
| (PCM1_RATIO << 16))
/* CLK_DIV_PERIC3 */
#define AUDIO2_RATIO 0x5
#define AUDIO1_RATIO 0x5
#define AUDIO0_RATIO 0x5
#define CLK_DIV_PERIC3_VAL ((AUDIO2_RATIO << 28) \
| (AUDIO1_RATIO << 24) \
| (AUDIO0_RATIO << 20))
/* CLK_DIV_PERIC4 */
#define SPI2_PRE_RATIO 0x2
#define SPI1_PRE_RATIO 0x2
#define SPI0_PRE_RATIO 0x2
#define CLK_DIV_PERIC4_VAL ((SPI2_PRE_RATIO << 24) \
| (SPI1_PRE_RATIO << 16) \
| (SPI0_PRE_RATIO << 8))
/* CLK_SRC_DISP1_0 */
#define CLK_SRC_DISP1_0_VAL 0x10666600
#define CLK_DIV_DISP1_0_VAL 0x01050211
#define APLL_FOUT (1 << 0)
#define KPLL_FOUT (1 << 0)
#define CLK_DIV_CPERI1_VAL 0x3f3f0000
#endif
struct mem_timings;
/* Errors that we can encourter in low-level setup */
enum {
SETUP_ERR_OK,
SETUP_ERR_RDLV_COMPLETE_TIMEOUT = -1,
SETUP_ERR_ZQ_CALIBRATION_FAILURE = -2,
};
/*
* Memory variant specific initialization code for DDR3
*
* @param mem Memory timings for this memory type.
* @param reset Reset DDR PHY during initialization.
* @return 0 if ok, SETUP_ERR_... if there is a problem
*/
int ddr3_mem_ctrl_init(struct mem_timings *mem, int reset);
/* Memory variant specific initialization code for LPDDR3 */
void lpddr3_mem_ctrl_init(void);
/*
* Configure ZQ I/O interface
*
* @param mem Memory timings for this memory type.
* @param phy0_con16 Register address for dmc_phy0->phy_con16
* @param phy1_con16 Register address for dmc_phy1->phy_con16
* @param phy0_con17 Register address for dmc_phy0->phy_con17
* @param phy1_con17 Register address for dmc_phy1->phy_con17
* @return 0 if ok, -1 on error
*/
int dmc_config_zq(struct mem_timings *mem, uint32_t *phy0_con16,
uint32_t *phy1_con16, uint32_t *phy0_con17,
uint32_t *phy1_con17);
/*
* Send NOP and MRS/EMRS Direct commands
*
* @param mem Memory timings for this memory type.
* @param directcmd Register address for dmc_phy->directcmd
*/
void dmc_config_mrs(struct mem_timings *mem, uint32_t *directcmd);
/*
* Send PALL Direct commands
*
* @param mem Memory timings for this memory type.
* @param directcmd Register address for dmc_phy->directcmd
*/
void dmc_config_prech(struct mem_timings *mem, uint32_t *directcmd);
/*
* Reset the DLL. This function is common between DDR3 and LPDDR2.
* However, the reset value is different. So we are passing a flag
* ddr_mode to distinguish between LPDDR2 and DDR3.
*
* @param phycontrol0 Register address for dmc_phy->phycontrol0
* @param ddr_mode Type of DDR memory
*/
void update_reset_dll(uint32_t *phycontrol0, enum ddr_mode);
#endif