mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-13 23:02:59 +00:00
6bacc73621
Spam detection software, running on the system "lists.denx.de",
has identified this incoming email as possible spam. The original
message has been attached to this so you can view it or label
similar future email. If you have any questions, see
@@CONTACT_ADDRESS@@ for details.
Content preview: Previous change to create _printch causes the stack to be
used, breaking printch before stack is available. Inline _printch to prevent
this happening. Signed-off-by: Tim Chick <tim.chick@mediatek.com> --- [...]
Content analysis details: (6.3 points, 5.0 required)
pts rule name description
---- ---------------------- --------------------------------------------------
0.7 RCVD_IN_XBL RBL: Received via a relay in Spamhaus XBL
[188.29.165.105 listed in zen.spamhaus.org]
3.6 RCVD_IN_PBL RBL: Received via a relay in Spamhaus PBL
1.6 RCVD_IN_BRBL_LASTEXT RBL: No description available.
[188.29.165.105 listed in bb.barracudacentral.org]
0.4 RDNS_DYNAMIC Delivered to internal network by host with
dynamic-looking rDNS
Previous change to create _printch causes the stack to be used,
breaking printch before stack is available. Inline _printch to
prevent this happening.
Signed-off-by: Tim Chick <tim.chick@mediatek.com>
171 lines
3.9 KiB
C
171 lines
3.9 KiB
C
/*
|
|
* Early debug UART support
|
|
*
|
|
* (C) Copyright 2014 Google, Inc
|
|
* Writte by Simon Glass <sjg@chromium.org>
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#ifndef _DEBUG_UART_H
|
|
#define _DEBUG_UART_H
|
|
|
|
/*
|
|
* The debug UART is intended for use very early in U-Boot to debug problems
|
|
* when an ICE or other debug mechanism is not available.
|
|
*
|
|
* To use it you should:
|
|
* - Make sure your UART supports this interface
|
|
* - Enable CONFIG_DEBUG_UART
|
|
* - Enable the CONFIG for your UART to tell it to provide this interface
|
|
* (e.g. CONFIG_DEBUG_UART_NS16550)
|
|
* - Define the required settings as needed (see below)
|
|
* - Call debug_uart_init() before use
|
|
* - Call printch() to output a character
|
|
*
|
|
* Depending on your platform it may be possible to use this UART before a
|
|
* stack is available.
|
|
*
|
|
* If your UART does not support this interface you can probably add support
|
|
* quite easily. Remember that you cannot use driver model and it is preferred
|
|
* to use no stack.
|
|
*
|
|
* You must not use this UART once driver model is working and the serial
|
|
* drivers are up and running (done in serial_init()). Otherwise the drivers
|
|
* may conflict and you will get strange output.
|
|
*
|
|
*
|
|
* To enable the debug UART in your serial driver:
|
|
*
|
|
* - #include <debug_uart.h>
|
|
* - Define _debug_uart_init(), trying to avoid using the stack
|
|
* - Define _debug_uart_putc() as static inline (avoiding stack usage)
|
|
* - Immediately afterwards, add DEBUG_UART_FUNCS to define the rest of the
|
|
* functionality (printch(), etc.)
|
|
*
|
|
* If your board needs additional init for the UART to work, enable
|
|
* CONFIG_DEBUG_UART_BOARD_INIT and write a function called
|
|
* board_debug_uart_init() to perform that init. When debug_uart_init() is
|
|
* called, the init will happen automatically.
|
|
*/
|
|
|
|
/**
|
|
* debug_uart_init() - Set up the debug UART ready for use
|
|
*
|
|
* This sets up the UART with the correct baud rate, etc.
|
|
*
|
|
* Available CONFIG is:
|
|
*
|
|
* - CONFIG_DEBUG_UART_BASE: Base address of UART
|
|
* - CONFIG_BAUDRATE: Requested baud rate
|
|
* - CONFIG_DEBUG_UART_CLOCK: Input clock for UART
|
|
*/
|
|
void debug_uart_init(void);
|
|
|
|
#ifdef CONFIG_DEBUG_UART_BOARD_INIT
|
|
void board_debug_uart_init(void);
|
|
#else
|
|
static inline void board_debug_uart_init(void)
|
|
{
|
|
}
|
|
#endif
|
|
|
|
/**
|
|
* printch() - Output a character to the debug UART
|
|
*
|
|
* @ch: Character to output
|
|
*/
|
|
void printch(int ch);
|
|
|
|
/**
|
|
* printascii() - Output an ASCII string to the debug UART
|
|
*
|
|
* @str: String to output
|
|
*/
|
|
void printascii(const char *str);
|
|
|
|
/**
|
|
* printhex2() - Output a 2-digit hex value
|
|
*
|
|
* @value: Value to output
|
|
*/
|
|
void printhex2(uint value);
|
|
|
|
/**
|
|
* printhex4() - Output a 4-digit hex value
|
|
*
|
|
* @value: Value to output
|
|
*/
|
|
void printhex4(uint value);
|
|
|
|
/**
|
|
* printhex8() - Output a 8-digit hex value
|
|
*
|
|
* @value: Value to output
|
|
*/
|
|
void printhex8(uint value);
|
|
|
|
#ifdef CONFIG_DEBUG_UART_ANNOUNCE
|
|
#define _DEBUG_UART_ANNOUNCE printascii("<debug_uart> ");
|
|
#else
|
|
#define _DEBUG_UART_ANNOUNCE
|
|
#endif
|
|
|
|
/*
|
|
* Now define some functions - this should be inserted into the serial driver
|
|
*/
|
|
#define DEBUG_UART_FUNCS \
|
|
\
|
|
static inline void _printch(int ch) \
|
|
{ \
|
|
if (ch == '\n') \
|
|
_debug_uart_putc('\r'); \
|
|
_debug_uart_putc(ch); \
|
|
} \
|
|
\
|
|
void printch(int ch) \
|
|
{ \
|
|
_printch(ch); \
|
|
} \
|
|
\
|
|
void printascii(const char *str) \
|
|
{ \
|
|
while (*str) \
|
|
_printch(*str++); \
|
|
} \
|
|
\
|
|
static inline void printhex1(uint digit) \
|
|
{ \
|
|
digit &= 0xf; \
|
|
_debug_uart_putc(digit > 9 ? digit - 10 + 'a' : digit + '0'); \
|
|
} \
|
|
\
|
|
static inline void printhex(uint value, int digits) \
|
|
{ \
|
|
while (digits-- > 0) \
|
|
printhex1(value >> (4 * digits)); \
|
|
} \
|
|
\
|
|
void printhex2(uint value) \
|
|
{ \
|
|
printhex(value, 2); \
|
|
} \
|
|
\
|
|
void printhex4(uint value) \
|
|
{ \
|
|
printhex(value, 4); \
|
|
} \
|
|
\
|
|
void printhex8(uint value) \
|
|
{ \
|
|
printhex(value, 8); \
|
|
} \
|
|
\
|
|
void debug_uart_init(void) \
|
|
{ \
|
|
board_debug_uart_init(); \
|
|
_debug_uart_init(); \
|
|
_DEBUG_UART_ANNOUNCE \
|
|
} \
|
|
|
|
#endif
|