u-boot/board/actux3/actux3.c
Wolfgang Denk 1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00

149 lines
3.3 KiB
C

/*
* (C) Copyright 2007
* Michael Schwingen, michael@schwingen.org
*
* (C) Copyright 2006
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
* (C) Copyright 2002
* Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
*
* (C) Copyright 2002
* Sysgo Real-Time Solutions, GmbH <www.elinos.com>
* Marius Groeger <mgroeger@sysgo.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <command.h>
#include <malloc.h>
#include <asm/arch/ixp425.h>
#include <asm/io.h>
#include <miiphy.h>
#include "actux3_hw.h"
DECLARE_GLOBAL_DATA_PTR;
int board_early_init_f(void)
{
/* CS1: IPAC-X */
writel(0x94d10013, IXP425_EXP_CS1);
/* CS5: Debug port */
writel(0x9d520003, IXP425_EXP_CS5);
/* CS6: Release/Option register */
writel(0x81860001, IXP425_EXP_CS6);
/* CS7: LEDs */
writel(0x80900003, IXP425_EXP_CS7);
return 0;
}
int board_init(void)
{
/* adress of boot parameters */
gd->bd->bi_boot_params = 0x00000100;
GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_IORST);
GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_ETHRST);
GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_DSR);
GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_DCD);
GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_LED5_GN);
GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_LED6_RT);
GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_LED6_GN);
GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST);
GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_ETHRST);
GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_DSR);
GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_DCD);
GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_LED5_GN);
GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_LED6_RT);
GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_LED6_GN);
/*
* Setup GPIO's for Interrupt inputs
*/
GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_DBGINT);
GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_ETHINT);
/*
* Setup GPIO's for 33MHz clock output
*/
GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK);
GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK);
writel(0x011001FF, IXP425_GPIO_GPCLKR);
/* we need a minimum PCI reset pulse width after enabling the clock */
udelay(533);
GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST);
GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_ETHRST);
ACTUX3_LED1_RT(1);
ACTUX3_LED1_GN(0);
ACTUX3_LED2_RT(0);
ACTUX3_LED2_GN(0);
ACTUX3_LED3_RT(0);
ACTUX3_LED3_GN(0);
ACTUX3_LED4_GN(0);
ACTUX3_LED5_RT(0);
return 0;
}
/*
* Check Board Identity
*/
int checkboard(void)
{
char buf[64];
int i = getenv_f("serial#", buf, sizeof(buf));
puts("Board: AcTux-3 rev.");
putc(ACTUX3_BOARDREL + 'A' - 1);
if (i > 0) {
puts (", serial# ");
puts (buf);
}
putc('\n');
return 0;
}
/*************************************************************************
* get_board_rev() - setup to pass kernel board revision information
* 0 = reserved
* 1 = Rev. A
* 2 = Rev. B
*************************************************************************/
u32 get_board_rev(void)
{
return ACTUX3_BOARDREL;
}
int dram_init(void)
{
gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, 128<<20);
return 0;
}
void reset_phy(void)
{
int i;
/* initialize the PHY */
miiphy_reset("NPE0", CONFIG_PHY_ADDR);
/* all LED outputs = Link/Act */
miiphy_write("NPE0", CONFIG_PHY_ADDR, 0x16, 0x0AAA);
/*
* The Marvell 88E6060 switch comes up with all ports disabled.
* set all ethernet switch ports to forwarding state
*/
for (i = 1; i <= 5; i++)
miiphy_write("NPE0", CONFIG_PHY_ADDR + 8 + i, 0x04, 0x03);
}