u-boot/board/karo/tk71/kwbimage.cfg
Wolfgang Denk 1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00

158 lines
5.2 KiB
INI

#
# (C) Copyright 2009
# Marvell Semiconductor <www.marvell.com>
# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
#
# adopted to TK71 by
# Nils Faerber <nils.faerber@kernelconcepts.de>
#
# SPDX-License-Identifier: GPL-2.0+
#
# Refer doc/README.kwbimage for more details about how-to configure
# and create kirkwood boot image
#
# Boot Media configurations
BOOT_FROM nand
NAND_ECC_MODE default
NAND_PAGE_SIZE 0x0800
# SOC registers configuration using bootrom header extension
# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
# Configure RGMII-0 interface pad voltage to 1.8V
DATA 0xFFD100e0 0x1b1b1b9b
#Dram initalization for SINGLE x16 CL=5 @ 400MHz
DATA 0xFFD01400 0x43000c30 # DDR Configuration register
# bit13-0: 0xc30 (3120 DDR2 clks refresh rate)
# bit23-14: zero
# bit24: 1= enable exit self refresh mode on DDR access
# bit25: 1 required
# bit29-26: zero
# bit31-30: 01
DATA 0xFFD01404 0x36543000 # DDR Controller Control Low
# bit 4: 0=addr/cmd in smame cycle
# bit 5: 0=clk is driven during self refresh, we don't care for APX
# bit 6: 0=use recommended falling edge of clk for addr/cmd
# bit14: 0=input buffer always powered up
# bit18: 1=cpu lock transaction enabled
# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
# bit30-28: 3 required
# bit31: 0=no additional STARTBURST delay
DATA 0xFFD01408 0x1101355b # DDR Timing (Low) (active cycles value +1)
# bit3-0: TRAS lsbs
# bit7-4: TRCD
# bit11- 8: TRP
# bit15-12: TWR
# bit19-16: TWTR
# bit20: TRAS msb
# bit23-21: 0x0
# bit27-24: TRRD
# bit31-28: TRTP
DATA 0xFFD0140C 0x00000034 # DDR Timing (High)
# bit6-0: TRFC
# bit8-7: TR2R
# bit10-9: TR2W
# bit12-11: TW2W
# bit31-13: zero required
DATA 0xFFD01410 0x00000000 # DDR Address Control
# bit1-0: 01, Cs0width=x16
# bit3-2: 10, Cs0size=512Mb
# bit5-4: 01, Cs1width=x16
# bit7-6: 10, Cs1size=512Mb
# bit9-8: 00, Cs2width=nonexistent
# bit11-10: 00, Cs2size =nonexistent
# bit13-12: 00, Cs3width=nonexistent
# bit15-14: 00, Cs3size =nonexistent
# bit16: 0, Cs0AddrSel
# bit17: 0, Cs1AddrSel
# bit18: 0, Cs2AddrSel
# bit19: 0, Cs3AddrSel
# bit31-20: 0 required
DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
# bit0: 0, OpenPage enabled
# bit31-1: 0 required
DATA 0xFFD01418 0x00000000 # DDR Operation
# bit3-0: 0x0, DDR cmd
# bit31-4: 0 required
DATA 0xFFD0141C 0x00000652 # DDR Mode
# bit2-0: 2, BurstLen=2 required
# bit3: 0, BurstType=0 required
# bit6-4: 4, CL=5
# bit7: 0, TestMode=0 normal
# bit8: 0, DLL reset=0 normal
# bit11-9: 6, auto-precharge write recovery ????????????
# bit12: 0, PD must be zero
# bit31-13: 0 required
DATA 0xFFD01420 0x00000042 # DDR Extended Mode
# bit0: 0, DDR DLL enabled
# bit1: 0, DDR drive strenght normal
# bit2: 0, DDR ODT control lsd (disabled)
# bit5-3: 000, required
# bit6: 1, DDR ODT control msb, (disabled)
# bit9-7: 000, required
# bit10: 0, differential DQS enabled
# bit11: 0, required
# bit12: 0, DDR output buffer enabled
# bit31-13: 0 required
DATA 0xFFD01424 0x0000F17F # DDR Controller Control High
# bit2-0: 111, required
# bit3 : 1 , MBUS Burst Chop disabled
# bit6-4: 111, required
# bit7 : 0
# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
# bit9 : 0 , no half clock cycle addition to dataout
# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
# bit15-12: 1111 required
# bit31-16: 0 required
DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
DATA 0xFFD01504 0x1FFFFFF1 # CS[0]n Size
# bit0: 1, Window enabled
# bit1: 0, Write Protect disabled
# bit3-2: 00, CS0 hit selected
# bit23-4: ones, required
# bit31-24: 0x0F, Size (i.e. 256MB)
DATA 0xFFD01508 0x00000000 # CS[1]n Base address to 256Mb
DATA 0xFFD0150C 0x00000000 # CS[1]n Size 256Mb Window enabled for CS1
DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
DATA 0xFFD01494 0x00110000 # DDR ODT Control (Low)
# bit3-0: 0010, (read) M_ODT[0] is asserted during read from DRAM CS1
# bit7-4: 0001, (read) M_ODT[1] is asserted during read from DRAM CS0
# bit19-16: 0010, (write) M_ODT[0] is asserted during write to DRAM CS1.
# bit23-20: 0001, (write) M_ODT[1] is asserted during write to DRAM CS0.
DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
# bit1-0: 00, ODT0 controlled by ODT Control (low) register above
# bit3-2: 01, ODT1 active NEVER!
# bit31-4: zero, required
DATA 0xFFD0149C 0x0000F80F # CPU ODT Control
# bit3-0: 1111, internal ODT is asserted during read from DRAM bank 0-3
# bit11-10: 01, M_DQ, M_DM, and M_DQS I/O buffer ODT Select: 150 ohm
# bit13-12: 10, M_STARTBURST_IN I/O buffer ODT Select: 75 ohm
# bit14: 1, M_STARTBURST_IN ODT: Enabled
# bit15: 1, DDR IO ODT Unit: Use ODT block
DATA 0xFFD01480 0x00000001 # DDR Initialization Control
#bit0=1, enable DDR init upon this register write
# End of Header extension
DATA 0x0 0x0