mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-13 14:53:06 +00:00
a3c252d6d6
Introudce a new function lcdif_power_down. 1. Waits for a VSYNC interrupt to guarantee the reset is done at the VSYNC edge, which somehow makes the LCDIF consume the display FIFO(?) and helps the LCDIF work normally at the kernel stage. 2. Add power down function to stop lcdif. The reason to introduce lcdif_power_down is that we want lcdif to be in initial state when doing uboot reset or before kernel boot to make system stable, otherwise system may hang. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Anatolij Gustschin <agust@denx.de> Acked-by: Anatolij Gustschin <agust@denx.de>
241 lines
6.3 KiB
C
241 lines
6.3 KiB
C
/*
|
|
* Freescale i.MX23/i.MX28 LCDIF driver
|
|
*
|
|
* Copyright (C) 2011-2013 Marek Vasut <marex@denx.de>
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
#include <common.h>
|
|
#include <malloc.h>
|
|
#include <video_fb.h>
|
|
|
|
#include <asm/arch/imx-regs.h>
|
|
#include <asm/arch/clock.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <asm/errno.h>
|
|
#include <asm/io.h>
|
|
|
|
#include <asm/imx-common/dma.h>
|
|
|
|
#include "videomodes.h"
|
|
|
|
#define PS2KHZ(ps) (1000000000UL / (ps))
|
|
|
|
static GraphicDevice panel;
|
|
struct mxs_dma_desc desc;
|
|
|
|
/**
|
|
* mxsfb_system_setup() - Fine-tune LCDIF configuration
|
|
*
|
|
* This function is used to adjust the LCDIF configuration. This is usually
|
|
* needed when driving the controller in System-Mode to operate an 8080 or
|
|
* 6800 connected SmartLCD.
|
|
*/
|
|
__weak void mxsfb_system_setup(void)
|
|
{
|
|
}
|
|
|
|
/*
|
|
* DENX M28EVK:
|
|
* setenv videomode
|
|
* video=ctfb:x:800,y:480,depth:18,mode:0,pclk:30066,
|
|
* le:0,ri:256,up:0,lo:45,hs:1,vs:1,sync:100663296,vmode:0
|
|
*
|
|
* Freescale mx23evk/mx28evk with a Seiko 4.3'' WVGA panel:
|
|
* setenv videomode
|
|
* video=ctfb:x:800,y:480,depth:24,mode:0,pclk:29851,
|
|
* le:89,ri:164,up:23,lo:10,hs:10,vs:10,sync:0,vmode:0
|
|
*/
|
|
|
|
static void mxs_lcd_init(GraphicDevice *panel,
|
|
struct ctfb_res_modes *mode, int bpp)
|
|
{
|
|
struct mxs_lcdif_regs *regs = (struct mxs_lcdif_regs *)MXS_LCDIF_BASE;
|
|
uint32_t word_len = 0, bus_width = 0;
|
|
uint8_t valid_data = 0;
|
|
|
|
/* Kick in the LCDIF clock */
|
|
mxs_set_lcdclk(MXS_LCDIF_BASE, PS2KHZ(mode->pixclock));
|
|
|
|
/* Restart the LCDIF block */
|
|
mxs_reset_block(®s->hw_lcdif_ctrl_reg);
|
|
|
|
switch (bpp) {
|
|
case 24:
|
|
word_len = LCDIF_CTRL_WORD_LENGTH_24BIT;
|
|
bus_width = LCDIF_CTRL_LCD_DATABUS_WIDTH_24BIT;
|
|
valid_data = 0x7;
|
|
break;
|
|
case 18:
|
|
word_len = LCDIF_CTRL_WORD_LENGTH_24BIT;
|
|
bus_width = LCDIF_CTRL_LCD_DATABUS_WIDTH_18BIT;
|
|
valid_data = 0x7;
|
|
break;
|
|
case 16:
|
|
word_len = LCDIF_CTRL_WORD_LENGTH_16BIT;
|
|
bus_width = LCDIF_CTRL_LCD_DATABUS_WIDTH_16BIT;
|
|
valid_data = 0xf;
|
|
break;
|
|
case 8:
|
|
word_len = LCDIF_CTRL_WORD_LENGTH_8BIT;
|
|
bus_width = LCDIF_CTRL_LCD_DATABUS_WIDTH_8BIT;
|
|
valid_data = 0xf;
|
|
break;
|
|
}
|
|
|
|
writel(bus_width | word_len | LCDIF_CTRL_DOTCLK_MODE |
|
|
LCDIF_CTRL_BYPASS_COUNT | LCDIF_CTRL_LCDIF_MASTER,
|
|
®s->hw_lcdif_ctrl);
|
|
|
|
writel(valid_data << LCDIF_CTRL1_BYTE_PACKING_FORMAT_OFFSET,
|
|
®s->hw_lcdif_ctrl1);
|
|
|
|
mxsfb_system_setup();
|
|
|
|
writel((mode->yres << LCDIF_TRANSFER_COUNT_V_COUNT_OFFSET) | mode->xres,
|
|
®s->hw_lcdif_transfer_count);
|
|
|
|
writel(LCDIF_VDCTRL0_ENABLE_PRESENT | LCDIF_VDCTRL0_ENABLE_POL |
|
|
LCDIF_VDCTRL0_VSYNC_PERIOD_UNIT |
|
|
LCDIF_VDCTRL0_VSYNC_PULSE_WIDTH_UNIT |
|
|
mode->vsync_len, ®s->hw_lcdif_vdctrl0);
|
|
writel(mode->upper_margin + mode->lower_margin +
|
|
mode->vsync_len + mode->yres,
|
|
®s->hw_lcdif_vdctrl1);
|
|
writel((mode->hsync_len << LCDIF_VDCTRL2_HSYNC_PULSE_WIDTH_OFFSET) |
|
|
(mode->left_margin + mode->right_margin +
|
|
mode->hsync_len + mode->xres),
|
|
®s->hw_lcdif_vdctrl2);
|
|
writel(((mode->left_margin + mode->hsync_len) <<
|
|
LCDIF_VDCTRL3_HORIZONTAL_WAIT_CNT_OFFSET) |
|
|
(mode->upper_margin + mode->vsync_len),
|
|
®s->hw_lcdif_vdctrl3);
|
|
writel((0 << LCDIF_VDCTRL4_DOTCLK_DLY_SEL_OFFSET) | mode->xres,
|
|
®s->hw_lcdif_vdctrl4);
|
|
|
|
writel(panel->frameAdrs, ®s->hw_lcdif_cur_buf);
|
|
writel(panel->frameAdrs, ®s->hw_lcdif_next_buf);
|
|
|
|
/* Flush FIFO first */
|
|
writel(LCDIF_CTRL1_FIFO_CLEAR, ®s->hw_lcdif_ctrl1_set);
|
|
|
|
#ifndef CONFIG_VIDEO_MXS_MODE_SYSTEM
|
|
/* Sync signals ON */
|
|
setbits_le32(®s->hw_lcdif_vdctrl4, LCDIF_VDCTRL4_SYNC_SIGNALS_ON);
|
|
#endif
|
|
|
|
/* FIFO cleared */
|
|
writel(LCDIF_CTRL1_FIFO_CLEAR, ®s->hw_lcdif_ctrl1_clr);
|
|
|
|
/* RUN! */
|
|
writel(LCDIF_CTRL_RUN, ®s->hw_lcdif_ctrl_set);
|
|
}
|
|
|
|
void lcdif_power_down(void)
|
|
{
|
|
struct mxs_lcdif_regs *regs = (struct mxs_lcdif_regs *)MXS_LCDIF_BASE;
|
|
int timeout = 1000000;
|
|
|
|
writel(panel.frameAdrs, ®s->hw_lcdif_cur_buf_reg);
|
|
writel(panel.frameAdrs, ®s->hw_lcdif_next_buf_reg);
|
|
writel(LCDIF_CTRL1_VSYNC_EDGE_IRQ, ®s->hw_lcdif_ctrl1_clr);
|
|
while (--timeout) {
|
|
if (readl(®s->hw_lcdif_ctrl1_reg) &
|
|
LCDIF_CTRL1_VSYNC_EDGE_IRQ)
|
|
break;
|
|
udelay(1);
|
|
}
|
|
mxs_reset_block((struct mxs_register_32 *)®s->hw_lcdif_ctrl_reg);
|
|
}
|
|
|
|
void *video_hw_init(void)
|
|
{
|
|
int bpp = -1;
|
|
char *penv;
|
|
void *fb;
|
|
struct ctfb_res_modes mode;
|
|
|
|
puts("Video: ");
|
|
|
|
/* Suck display configuration from "videomode" variable */
|
|
penv = getenv("videomode");
|
|
if (!penv) {
|
|
puts("MXSFB: 'videomode' variable not set!\n");
|
|
return NULL;
|
|
}
|
|
|
|
bpp = video_get_params(&mode, penv);
|
|
|
|
/* fill in Graphic device struct */
|
|
sprintf(panel.modeIdent, "%dx%dx%d",
|
|
mode.xres, mode.yres, bpp);
|
|
|
|
panel.winSizeX = mode.xres;
|
|
panel.winSizeY = mode.yres;
|
|
panel.plnSizeX = mode.xres;
|
|
panel.plnSizeY = mode.yres;
|
|
|
|
switch (bpp) {
|
|
case 24:
|
|
case 18:
|
|
panel.gdfBytesPP = 4;
|
|
panel.gdfIndex = GDF_32BIT_X888RGB;
|
|
break;
|
|
case 16:
|
|
panel.gdfBytesPP = 2;
|
|
panel.gdfIndex = GDF_16BIT_565RGB;
|
|
break;
|
|
case 8:
|
|
panel.gdfBytesPP = 1;
|
|
panel.gdfIndex = GDF__8BIT_INDEX;
|
|
break;
|
|
default:
|
|
printf("MXSFB: Invalid BPP specified! (bpp = %i)\n", bpp);
|
|
return NULL;
|
|
}
|
|
|
|
panel.memSize = mode.xres * mode.yres * panel.gdfBytesPP;
|
|
|
|
/* Allocate framebuffer */
|
|
fb = memalign(ARCH_DMA_MINALIGN,
|
|
roundup(panel.memSize, ARCH_DMA_MINALIGN));
|
|
if (!fb) {
|
|
printf("MXSFB: Error allocating framebuffer!\n");
|
|
return NULL;
|
|
}
|
|
|
|
/* Wipe framebuffer */
|
|
memset(fb, 0, panel.memSize);
|
|
|
|
panel.frameAdrs = (u32)fb;
|
|
|
|
printf("%s\n", panel.modeIdent);
|
|
|
|
/* Start framebuffer */
|
|
mxs_lcd_init(&panel, &mode, bpp);
|
|
|
|
#ifdef CONFIG_VIDEO_MXS_MODE_SYSTEM
|
|
/*
|
|
* If the LCD runs in system mode, the LCD refresh has to be triggered
|
|
* manually by setting the RUN bit in HW_LCDIF_CTRL register. To avoid
|
|
* having to set this bit manually after every single change in the
|
|
* framebuffer memory, we set up specially crafted circular DMA, which
|
|
* sets the RUN bit, then waits until it gets cleared and repeats this
|
|
* infinitelly. This way, we get smooth continuous updates of the LCD.
|
|
*/
|
|
struct mxs_lcdif_regs *regs = (struct mxs_lcdif_regs *)MXS_LCDIF_BASE;
|
|
|
|
memset(&desc, 0, sizeof(struct mxs_dma_desc));
|
|
desc.address = (dma_addr_t)&desc;
|
|
desc.cmd.data = MXS_DMA_DESC_COMMAND_NO_DMAXFER | MXS_DMA_DESC_CHAIN |
|
|
MXS_DMA_DESC_WAIT4END |
|
|
(1 << MXS_DMA_DESC_PIO_WORDS_OFFSET);
|
|
desc.cmd.pio_words[0] = readl(®s->hw_lcdif_ctrl) | LCDIF_CTRL_RUN;
|
|
desc.cmd.next = (uint32_t)&desc.cmd;
|
|
|
|
/* Execute the DMA chain. */
|
|
mxs_dma_circ_start(MXS_DMA_CHANNEL_AHB_APBH_LCDIF, &desc);
|
|
#endif
|
|
|
|
return (void *)&panel;
|
|
}
|