u-boot/drivers/net/phy/mv88e61xx.c
Prafulla Wadaskar 443ce4ac9d net: phy: bugfixes: mv88E61xx multichip addressing support
With these fixes, this driver works properly for multi chip
addressging mode

Bugfixes:
1. Build error fixed for function mv88e61xx_busychk_multic-fixed
2. PHY dev address error detection- fixed
3. wrong busy bit was refered in function mv88e61xx_busychk -fixed
4. invalid data read ptr was refered for RD_PHY in case of
	multichip addressing mode -fixed

The Multichip Address mode is tested with RD6281A board having
MV88E6165 switch on it

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-07-22 22:53:45 -07:00

413 lines
11 KiB
C

/*
* (C) Copyright 2009
* Marvell Semiconductor <www.marvell.com>
* Prafulla Wadaskar <prafulla@marvell.com>
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
* MA 02110-1301 USA
*/
#include <common.h>
#include <netdev.h>
#include "mv88e61xx.h"
#ifdef CONFIG_MV88E61XX_MULTICHIP_ADRMODE
/* Chip Address mode
* The Switch support two modes of operation
* 1. single chip mode and
* 2. Multi-chip mode
* Refer section 9.2 &9.3 in chip datasheet-02 for more details
*
* By default single chip mode is configured
* multichip mode operation can be configured in board header
*/
static int mv88e61xx_busychk_multic(char *name, u32 devaddr)
{
u32 reg = 0;
u32 timeout = MV88E61XX_PHY_TIMEOUT;
/* Poll till SMIBusy bit is clear */
do {
miiphy_read(name, devaddr, 0x0, &reg);
if (timeout-- == 0) {
printf("SMI busy timeout\n");
return -1;
}
} while (reg & (1 << 15));
return 0;
}
static void mv88e61xx_wr_phy(char *name, u32 phy_adr, u32 reg_ofs, u16 data)
{
u16 reg;
u32 mii_dev_addr;
/* command to read PHY dev address */
if (miiphy_read(name, 0xEE, 0xEE, &mii_dev_addr)) {
printf("Error..could not read PHY dev address\n");
return;
}
mv88e61xx_busychk_multic(name, mii_dev_addr);
/* Write data to Switch indirect data register */
miiphy_write(name, mii_dev_addr, 0x1, data);
/* Write command to Switch indirect command register (write) */
miiphy_write(name, mii_dev_addr, 0x0,
reg_ofs | (phy_adr << 5) | (1 << 10) | (1 << 12) | (1 <<
15));
}
static void mv88e61xx_rd_phy(char *name, u32 phy_adr, u32 reg_ofs, u16 * data)
{
u16 reg;
u32 mii_dev_addr;
/* command to read PHY dev address */
if (miiphy_read(name, 0xEE, 0xEE, &mii_dev_addr)) {
printf("Error..could not read PHY dev address\n");
return;
}
mv88e61xx_busychk_multic(name, mii_dev_addr);
/* Write command to Switch indirect command register (read) */
miiphy_write(name, mii_dev_addr, 0x0,
reg_ofs | (phy_adr << 5) | (1 << 11) | (1 << 12) | (1 <<
15));
mv88e61xx_busychk_multic(name, mii_dev_addr);
/* Read data from Switch indirect data register */
miiphy_read(name, mii_dev_addr, 0x1, data);
}
#endif /* CONFIG_MV88E61XX_MULTICHIP_ADRMODE */
static void mv88e61xx_port_vlan_config(struct mv88e61xx_config *swconfig,
u32 max_prtnum, u32 ports_ofs)
{
u32 prt;
u16 reg;
char *name = swconfig->name;
u32 cpu_port = swconfig->cpuport;
u32 port_mask = swconfig->ports_enabled;
enum mv88e61xx_cfg_vlan vlancfg = swconfig->vlancfg;
/* be sure all ports are disabled */
for (prt = 0; prt < max_prtnum; prt++) {
RD_PHY(name, ports_ofs + prt, MV88E61XX_PRT_CTRL_REG, &reg);
reg &= ~0x3;
WR_PHY(name, ports_ofs + prt, MV88E61XX_PRT_CTRL_REG, reg);
if (!(cpu_port & (1 << prt)))
continue;
/* Set CPU port VID to 0x1 */
RD_PHY(name, (ports_ofs + prt), MV88E61XX_PRT_VID_REG, &reg);
reg &= ~0xfff;
reg |= 0x1;
WR_PHY(name, (ports_ofs + prt), MV88E61XX_PRT_VID_REG, reg);
}
/* Setting Port default priority for all ports to zero */
for (prt = 0; prt < max_prtnum; prt++) {
RD_PHY(name, ports_ofs + prt, MV88E61XX_PRT_VID_REG, &reg);
reg &= ~0xc000;
WR_PHY(name, ports_ofs + prt, MV88E61XX_PRT_VID_REG, reg);
}
/* Setting VID and VID map for all ports except CPU port */
for (prt = 0; prt < max_prtnum; prt++) {
/* only for enabled ports */
if ((1 << prt) & port_mask) {
/* skip CPU port */
if ((1 << prt) & cpu_port) {
/*
* Set Vlan map table for cpu_port to see
* all ports
*/
RD_PHY(name, (ports_ofs + prt),
MV88E61XX_PRT_VMAP_REG, &reg);
reg &= ~((1 << max_prtnum) - 1);
reg |= port_mask & ~(1 << prt);
WR_PHY(name, (ports_ofs + prt),
MV88E61XX_PRT_VMAP_REG, reg);
} else {
/*
* set Ports VLAN Mapping.
* port prt <--> cpu_port VLAN #prt+1.
*/
RD_PHY(name, ports_ofs + prt,
MV88E61XX_PRT_VID_REG, &reg);
reg &= ~0x0fff;
reg |= (prt + 1);
WR_PHY(name, ports_ofs + prt,
MV88E61XX_PRT_VID_REG, reg);
RD_PHY(name, ports_ofs + prt,
MV88E61XX_PRT_VMAP_REG, &reg);
if (vlancfg == MV88E61XX_VLANCFG_DEFAULT) {
/*
* all any port can send frames to all other ports
* ref: sec 3.2.1.1 of datasheet
*/
reg |= 0x03f;
reg &= ~(1 << prt);
} else if (vlancfg == MV88E61XX_VLANCFG_ROUTER) {
/*
* all other ports can send frames to CPU port only
* ref: sec 3.2.1.2 of datasheet
*/
reg &= ~((1 << max_prtnum) - 1);
reg |= cpu_port;
}
WR_PHY(name, ports_ofs + prt,
MV88E61XX_PRT_VMAP_REG, reg);
}
}
}
/*
* enable only appropriate ports to forwarding mode
* and disable the others
*/
for (prt = 0; prt < max_prtnum; prt++) {
if ((1 << prt) & port_mask) {
RD_PHY(name, ports_ofs + prt,
MV88E61XX_PRT_CTRL_REG, &reg);
reg |= 0x3;
WR_PHY(name, ports_ofs + prt,
MV88E61XX_PRT_CTRL_REG, reg);
} else {
/* Disable port */
RD_PHY(name, ports_ofs + prt,
MV88E61XX_PRT_CTRL_REG, &reg);
reg &= ~0x3;
WR_PHY(name, ports_ofs + prt,
MV88E61XX_PRT_CTRL_REG, reg);
}
}
}
/*
* Make sure SMIBusy bit cleared before another
* SMI operation can take place
*/
static int mv88e61xx_busychk(char *name)
{
u32 reg = 0;
u32 timeout = MV88E61XX_PHY_TIMEOUT;
do {
RD_PHY(name, MV88E61XX_GLB2REG_DEVADR,
MV88E61XX_PHY_CMD, (u16 *) & reg);
if (timeout-- == 0) {
printf("SMI busy timeout\n");
return -1;
}
} while (reg & 1 << 15); /* busy mask */
return 0;
}
/*
* Power up the specified port and reset PHY
*/
static int mv88361xx_powerup(struct mv88e61xx_config *swconfig, u32 prt)
{
char *name = swconfig->name;
/* Write Copper Specific control reg1 (0x14) for-
* Enable Phy power up
* Energy Detect on (sense&Xmit NLP Periodically
* reset other settings default
*/
WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, 0x3360);
WR_PHY(name, MV88E61XX_GLB2REG_DEVADR,
MV88E61XX_PHY_CMD, (0x9410 | (prt << 5)));
if (mv88e61xx_busychk(name))
return -1;
/* Write PHY ctrl reg (0x0) to apply
* Phy reset (set bit 15 low)
* reset other default values
*/
WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, 0x1140);
WR_PHY(name, MV88E61XX_GLB2REG_DEVADR,
MV88E61XX_PHY_CMD, (0x9400 | (prt << 5)));
if (mv88e61xx_busychk(name))
return -1;
return 0;
}
/*
* Default Setup for LED[0]_Control (ref: Table 46 Datasheet-3)
* is set to "On-1000Mb/s Link, Off Else"
* This function sets it to "On-Link, Blink-Activity, Off-NoLink"
*
* This is optional settings may be needed on some boards
* to setup PHY LEDs default configuration to detect 10/100/1000Mb/s
* Link status
*/
static int mv88361xx_led_init(struct mv88e61xx_config *swconfig, u32 prt)
{
char *name = swconfig->name;
u16 reg;
if (swconfig->led_init != MV88E61XX_LED_INIT_EN)
return 0;
/* set page address to 3 */
reg = 3;
WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, reg);
WR_PHY(name, MV88E61XX_GLB2REG_DEVADR,
MV88E61XX_PHY_CMD, (1 << MV88E61XX_BUSY_OFST |
1 << MV88E61XX_MODE_OFST |
1 << MV88E61XX_OP_OFST |
prt << MV88E61XX_ADDR_OFST | 22));
if (mv88e61xx_busychk(name))
return -1;
/* set LED Func Ctrl reg */
reg = 1; /* LED[0] On-Link, Blink-Activity, Off-NoLink */
WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, reg);
WR_PHY(name, MV88E61XX_GLB2REG_DEVADR,
MV88E61XX_PHY_CMD, (1 << MV88E61XX_BUSY_OFST |
1 << MV88E61XX_MODE_OFST |
1 << MV88E61XX_OP_OFST |
prt << MV88E61XX_ADDR_OFST | 16));
if (mv88e61xx_busychk(name))
return -1;
/* set page address to 0 */
reg = 0;
WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, reg);
WR_PHY(name, MV88E61XX_GLB2REG_DEVADR,
MV88E61XX_PHY_CMD, (1 << MV88E61XX_BUSY_OFST |
1 << MV88E61XX_MODE_OFST |
1 << MV88E61XX_OP_OFST |
prt << MV88E61XX_ADDR_OFST | 22));
if (mv88e61xx_busychk(name))
return -1;
return 0;
}
/*
* Reverse Transmit polarity for Media Dependent Interface
* Pins (MDIP) bits in Copper Specific Control Register 3
* (Page 0, Reg 20 for each phy (except cpu port)
* Reference: Section 1.1 Switch datasheet-3
*
* This is optional settings may be needed on some boards
* for PHY<->magnetics h/w tuning
*/
static int mv88361xx_reverse_mdipn(struct mv88e61xx_config *swconfig, u32 prt)
{
char *name = swconfig->name;
u16 reg;
if (swconfig->mdip != MV88E61XX_MDIP_REVERSE)
return 0;
reg = 0x0f; /*Reverse MDIP/N[3:0] bits */
WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, reg);
WR_PHY(name, MV88E61XX_GLB2REG_DEVADR,
MV88E61XX_PHY_CMD, (1 << MV88E61XX_BUSY_OFST |
1 << MV88E61XX_MODE_OFST |
1 << MV88E61XX_OP_OFST |
prt << MV88E61XX_ADDR_OFST | 20));
if (mv88e61xx_busychk(name))
return -1;
return 0;
}
/*
* Marvell 88E61XX Switch initialization
*/
int mv88e61xx_switch_initialize(struct mv88e61xx_config *swconfig)
{
u32 prt;
u16 reg;
char *idstr;
char *name = swconfig->name;
if (miiphy_set_current_dev(name)) {
printf("%s failed\n", __FUNCTION__);
return -1;
}
if (!(swconfig->cpuport & ((1 << 4) | (1 << 5)))) {
swconfig->cpuport = (1 << 5);
printf("Invalid cpu port config, using default port5\n");
}
RD_PHY(name, MV88E61XX_PRT_OFST, PHY_PHYIDR2, &reg);
reg &= 0xfff0;
if (reg == 0x1610)
idstr = "88E6161";
if (reg == 0x1650)
idstr = "88E6165";
if (reg == 0x1210) {
idstr = "88E6123";
/* ports 2,3,4 not available */
swconfig->ports_enabled &= 0x023;
}
/* Port based VLANs configuration */
if ((swconfig->vlancfg == MV88E61XX_VLANCFG_DEFAULT)
|| (swconfig->vlancfg == MV88E61XX_VLANCFG_ROUTER))
mv88e61xx_port_vlan_config(swconfig, MV88E61XX_MAX_PORTS_NUM,
MV88E61XX_PRT_OFST);
else {
printf("Unsupported mode %s failed\n", __FUNCTION__);
return -1;
}
if (swconfig->rgmii_delay == MV88E61XX_RGMII_DELAY_EN) {
/*
* Enable RGMII delay on Tx and Rx for CPU port
* Ref: sec 9.5 of chip datasheet-02
*/
WR_PHY(name, MV88E61XX_PRT_OFST + 5,
MV88E61XX_RGMII_TIMECTRL_REG, 0x18);
WR_PHY(name, MV88E61XX_PRT_OFST + 4,
MV88E61XX_RGMII_TIMECTRL_REG, 0xc1e7);
}
for (prt = 0; prt < MV88E61XX_MAX_PORTS_NUM; prt++) {
if (!((1 << prt) & swconfig->cpuport)) {
if (mv88361xx_led_init(swconfig, prt))
return -1;
if (mv88361xx_reverse_mdipn(swconfig, prt))
return -1;
if (mv88361xx_powerup(swconfig, prt))
return -1;
}
/*Program port state */
RD_PHY(name, MV88E61XX_PRT_OFST + prt,
MV88E61XX_PRT_CTRL_REG, &reg);
WR_PHY(name, MV88E61XX_PRT_OFST + prt,
MV88E61XX_PRT_CTRL_REG,
reg | (swconfig->portstate & 0x03));
}
printf("%s Initialized on %s\n", idstr, name);
return 0;
}