u-boot/board/gdsys/mpc8308/hrcon.c
Tom Rini 83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00

498 lines
9.9 KiB
C

// SPDX-License-Identifier: GPL-2.0+
/*
* (C) Copyright 2014
* Dirk Eibach, Guntermann & Drunck GmbH, dirk.eibach@gdsys.cc
*/
#include <common.h>
#include <hwconfig.h>
#include <i2c.h>
#include <spi.h>
#include <linux/libfdt.h>
#include <fdt_support.h>
#include <pci.h>
#include <mpc83xx.h>
#include <fsl_esdhc.h>
#include <asm/io.h>
#include <asm/fsl_serdes.h>
#include <asm/fsl_mpc83xx_serdes.h>
#include "mpc8308.h"
#include <gdsys_fpga.h>
#include "../common/ioep-fpga.h"
#include "../common/osd.h"
#include "../common/mclink.h"
#include "../common/phy.h"
#include "../common/fanctrl.h"
#include <pca953x.h>
#include <pca9698.h>
#include <miiphy.h>
#define MAX_MUX_CHANNELS 2
enum {
MCFPGA_DONE = 1 << 0,
MCFPGA_INIT_N = 1 << 1,
MCFPGA_PROGRAM_N = 1 << 2,
MCFPGA_UPDATE_ENABLE_N = 1 << 3,
MCFPGA_RESET_N = 1 << 4,
};
enum {
GPIO_MDC = 1 << 14,
GPIO_MDIO = 1 << 15,
};
unsigned int mclink_fpgacount;
struct ihs_fpga *fpga_ptr[] = CONFIG_SYS_FPGA_PTR;
struct {
u8 bus;
u8 addr;
} hrcon_fans[] = CONFIG_HRCON_FANS;
int fpga_set_reg(u32 fpga, u16 *reg, off_t regoff, u16 data)
{
int res;
switch (fpga) {
case 0:
out_le16(reg, data);
break;
default:
res = mclink_send(fpga - 1, regoff, data);
if (res < 0) {
printf("mclink_send reg %02lx data %04x returned %d\n",
regoff, data, res);
return res;
}
break;
}
return 0;
}
int fpga_get_reg(u32 fpga, u16 *reg, off_t regoff, u16 *data)
{
int res;
switch (fpga) {
case 0:
*data = in_le16(reg);
break;
default:
if (fpga > mclink_fpgacount)
return -EINVAL;
res = mclink_receive(fpga - 1, regoff, data);
if (res < 0) {
printf("mclink_receive reg %02lx returned %d\n",
regoff, res);
return res;
}
}
return 0;
}
int checkboard(void)
{
char *s = env_get("serial#");
bool hw_type_cat = pca9698_get_value(0x20, 20);
puts("Board: ");
printf("HRCon %s", hw_type_cat ? "CAT" : "Fiber");
if (s != NULL) {
puts(", serial# ");
puts(s);
}
puts("\n");
return 0;
}
int last_stage_init(void)
{
int slaves;
unsigned int k;
unsigned int mux_ch;
unsigned char mclink_controllers[] = { 0x3c, 0x3d, 0x3e };
u16 fpga_features;
bool hw_type_cat = pca9698_get_value(0x20, 20);
bool ch0_rgmii2_present = false;
FPGA_GET_REG(0, fpga_features, &fpga_features);
/* Turn on Parade DP501 */
pca9698_direction_output(0x20, 10, 1);
pca9698_direction_output(0x20, 11, 1);
ch0_rgmii2_present = !pca9698_get_value(0x20, 30);
/* wait for FPGA done, then reset FPGA */
for (k = 0; k < ARRAY_SIZE(mclink_controllers); ++k) {
unsigned int ctr = 0;
if (i2c_probe(mclink_controllers[k]))
continue;
while (!(pca953x_get_val(mclink_controllers[k])
& MCFPGA_DONE)) {
udelay(100000);
if (ctr++ > 5) {
printf("no done for mclink_controller %d\n", k);
break;
}
}
pca953x_set_dir(mclink_controllers[k], MCFPGA_RESET_N, 0);
pca953x_set_val(mclink_controllers[k], MCFPGA_RESET_N, 0);
udelay(10);
pca953x_set_val(mclink_controllers[k], MCFPGA_RESET_N,
MCFPGA_RESET_N);
}
if (hw_type_cat) {
int retval;
struct mii_dev *mdiodev = mdio_alloc();
if (!mdiodev)
return -ENOMEM;
strncpy(mdiodev->name, bb_miiphy_buses[0].name, MDIO_NAME_LEN);
mdiodev->read = bb_miiphy_read;
mdiodev->write = bb_miiphy_write;
retval = mdio_register(mdiodev);
if (retval < 0)
return retval;
for (mux_ch = 0; mux_ch < MAX_MUX_CHANNELS; ++mux_ch) {
if ((mux_ch == 1) && !ch0_rgmii2_present)
continue;
setup_88e1514(bb_miiphy_buses[0].name, mux_ch);
}
}
/* give slave-PLLs and Parade DP501 some time to be up and running */
udelay(500000);
mclink_fpgacount = CONFIG_SYS_MCLINK_MAX;
slaves = mclink_probe();
mclink_fpgacount = 0;
ioep_fpga_print_info(0);
osd_probe(0);
#ifdef CONFIG_SYS_OSD_DH
osd_probe(4);
#endif
if (slaves <= 0)
return 0;
mclink_fpgacount = slaves;
for (k = 1; k <= slaves; ++k) {
FPGA_GET_REG(k, fpga_features, &fpga_features);
ioep_fpga_print_info(k);
osd_probe(k);
#ifdef CONFIG_SYS_OSD_DH
osd_probe(k + 4);
#endif
if (hw_type_cat) {
int retval;
struct mii_dev *mdiodev = mdio_alloc();
if (!mdiodev)
return -ENOMEM;
strncpy(mdiodev->name, bb_miiphy_buses[k].name,
MDIO_NAME_LEN);
mdiodev->read = bb_miiphy_read;
mdiodev->write = bb_miiphy_write;
retval = mdio_register(mdiodev);
if (retval < 0)
return retval;
setup_88e1514(bb_miiphy_buses[k].name, 0);
}
}
for (k = 0; k < ARRAY_SIZE(hrcon_fans); ++k) {
i2c_set_bus_num(hrcon_fans[k].bus);
init_fan_controller(hrcon_fans[k].addr);
}
return 0;
}
/*
* provide access to fpga gpios and controls (for I2C bitbang)
* (these may look all too simple but make iocon.h much more readable)
*/
void fpga_gpio_set(unsigned int bus, int pin)
{
FPGA_SET_REG(bus >= 4 ? (bus - 4) : bus, gpio.set, pin);
}
void fpga_gpio_clear(unsigned int bus, int pin)
{
FPGA_SET_REG(bus >= 4 ? (bus - 4) : bus, gpio.clear, pin);
}
int fpga_gpio_get(unsigned int bus, int pin)
{
u16 val;
FPGA_GET_REG(bus >= 4 ? (bus - 4) : bus, gpio.read, &val);
return val & pin;
}
void fpga_control_set(unsigned int bus, int pin)
{
u16 val;
FPGA_GET_REG(bus >= 4 ? (bus - 4) : bus, control, &val);
FPGA_SET_REG(bus >= 4 ? (bus - 4) : bus, control, val | pin);
}
void fpga_control_clear(unsigned int bus, int pin)
{
u16 val;
FPGA_GET_REG(bus >= 4 ? (bus - 4) : bus, control, &val);
FPGA_SET_REG(bus >= 4 ? (bus - 4) : bus, control, val & ~pin);
}
void mpc8308_init(void)
{
pca9698_direction_output(0x20, 4, 1);
}
void mpc8308_set_fpga_reset(unsigned state)
{
pca9698_set_value(0x20, 4, state ? 0 : 1);
}
void mpc8308_setup_hw(void)
{
immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
/*
* set "startup-finished"-gpios
*/
setbits_be32(&immr->gpio[0].dir, (1 << (31-11)) | (1 << (31-12)));
setbits_be32(&immr->gpio[0].dat, 1 << (31-12));
}
int mpc8308_get_fpga_done(unsigned fpga)
{
return pca9698_get_value(0x20, 19);
}
#ifdef CONFIG_FSL_ESDHC
int board_mmc_init(bd_t *bd)
{
immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
sysconf83xx_t *sysconf = &immr->sysconf;
/* Enable cache snooping in eSDHC system configuration register */
out_be32(&sysconf->sdhccr, 0x02000000);
return fsl_esdhc_mmc_init(bd);
}
#endif
static struct pci_region pcie_regions_0[] = {
{
.bus_start = CONFIG_SYS_PCIE1_MEM_BASE,
.phys_start = CONFIG_SYS_PCIE1_MEM_PHYS,
.size = CONFIG_SYS_PCIE1_MEM_SIZE,
.flags = PCI_REGION_MEM,
},
{
.bus_start = CONFIG_SYS_PCIE1_IO_BASE,
.phys_start = CONFIG_SYS_PCIE1_IO_PHYS,
.size = CONFIG_SYS_PCIE1_IO_SIZE,
.flags = PCI_REGION_IO,
},
};
void pci_init_board(void)
{
immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
sysconf83xx_t *sysconf = &immr->sysconf;
law83xx_t *pcie_law = sysconf->pcielaw;
struct pci_region *pcie_reg[] = { pcie_regions_0 };
fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_PEX,
FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
/* Deassert the resets in the control register */
out_be32(&sysconf->pecr1, 0xE0008000);
udelay(2000);
/* Configure PCI Express Local Access Windows */
out_be32(&pcie_law[0].bar, CONFIG_SYS_PCIE1_BASE & LAWBAR_BAR);
out_be32(&pcie_law[0].ar, LBLAWAR_EN | LBLAWAR_512MB);
mpc83xx_pcie_init(1, pcie_reg);
}
ulong board_flash_get_legacy(ulong base, int banknum, flash_info_t *info)
{
info->portwidth = FLASH_CFI_16BIT;
info->chipwidth = FLASH_CFI_BY16;
info->interface = FLASH_CFI_X16;
return 1;
}
#if defined(CONFIG_OF_BOARD_SETUP)
int ft_board_setup(void *blob, bd_t *bd)
{
ft_cpu_setup(blob, bd);
fsl_fdt_fixup_dr_usb(blob, bd);
fdt_fixup_esdhc(blob, bd);
return 0;
}
#endif
/*
* FPGA MII bitbang implementation
*/
struct fpga_mii {
unsigned fpga;
int mdio;
} fpga_mii[] = {
{ 0, 1},
{ 1, 1},
{ 2, 1},
{ 3, 1},
};
static int mii_dummy_init(struct bb_miiphy_bus *bus)
{
return 0;
}
static int mii_mdio_active(struct bb_miiphy_bus *bus)
{
struct fpga_mii *fpga_mii = bus->priv;
if (fpga_mii->mdio)
FPGA_SET_REG(fpga_mii->fpga, gpio.set, GPIO_MDIO);
else
FPGA_SET_REG(fpga_mii->fpga, gpio.clear, GPIO_MDIO);
return 0;
}
static int mii_mdio_tristate(struct bb_miiphy_bus *bus)
{
struct fpga_mii *fpga_mii = bus->priv;
FPGA_SET_REG(fpga_mii->fpga, gpio.set, GPIO_MDIO);
return 0;
}
static int mii_set_mdio(struct bb_miiphy_bus *bus, int v)
{
struct fpga_mii *fpga_mii = bus->priv;
if (v)
FPGA_SET_REG(fpga_mii->fpga, gpio.set, GPIO_MDIO);
else
FPGA_SET_REG(fpga_mii->fpga, gpio.clear, GPIO_MDIO);
fpga_mii->mdio = v;
return 0;
}
static int mii_get_mdio(struct bb_miiphy_bus *bus, int *v)
{
u16 gpio;
struct fpga_mii *fpga_mii = bus->priv;
FPGA_GET_REG(fpga_mii->fpga, gpio.read, &gpio);
*v = ((gpio & GPIO_MDIO) != 0);
return 0;
}
static int mii_set_mdc(struct bb_miiphy_bus *bus, int v)
{
struct fpga_mii *fpga_mii = bus->priv;
if (v)
FPGA_SET_REG(fpga_mii->fpga, gpio.set, GPIO_MDC);
else
FPGA_SET_REG(fpga_mii->fpga, gpio.clear, GPIO_MDC);
return 0;
}
static int mii_delay(struct bb_miiphy_bus *bus)
{
udelay(1);
return 0;
}
struct bb_miiphy_bus bb_miiphy_buses[] = {
{
.name = "board0",
.init = mii_dummy_init,
.mdio_active = mii_mdio_active,
.mdio_tristate = mii_mdio_tristate,
.set_mdio = mii_set_mdio,
.get_mdio = mii_get_mdio,
.set_mdc = mii_set_mdc,
.delay = mii_delay,
.priv = &fpga_mii[0],
},
{
.name = "board1",
.init = mii_dummy_init,
.mdio_active = mii_mdio_active,
.mdio_tristate = mii_mdio_tristate,
.set_mdio = mii_set_mdio,
.get_mdio = mii_get_mdio,
.set_mdc = mii_set_mdc,
.delay = mii_delay,
.priv = &fpga_mii[1],
},
{
.name = "board2",
.init = mii_dummy_init,
.mdio_active = mii_mdio_active,
.mdio_tristate = mii_mdio_tristate,
.set_mdio = mii_set_mdio,
.get_mdio = mii_get_mdio,
.set_mdc = mii_set_mdc,
.delay = mii_delay,
.priv = &fpga_mii[2],
},
{
.name = "board3",
.init = mii_dummy_init,
.mdio_active = mii_mdio_active,
.mdio_tristate = mii_mdio_tristate,
.set_mdio = mii_set_mdio,
.get_mdio = mii_get_mdio,
.set_mdc = mii_set_mdc,
.delay = mii_delay,
.priv = &fpga_mii[3],
},
};
int bb_miiphy_buses_num = sizeof(bb_miiphy_buses) /
sizeof(bb_miiphy_buses[0]);