mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-15 15:53:02 +00:00
59a72caba9
fdt_addr variable is the location in flash of the device tree blob [1], it does not exist for verdin-imx8mm. Because of this the bootefi command fails unless the optional `[fdt address]` parameter is passed on the command line, bootefi.c:efi_install_fdt() assumes that `fdt_addr` is valid when present. Fix this removing fdt_addr from the U-Boot environment. [1] doc/usage/environment.rst Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
70 lines
2 KiB
C
70 lines
2 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* Copyright 2020-2021 Toradex
|
|
*/
|
|
|
|
#ifndef __VERDIN_IMX8MM_H
|
|
#define __VERDIN_IMX8MM_H
|
|
|
|
#include <asm/arch/imx-regs.h>
|
|
#include <linux/sizes.h>
|
|
|
|
#define CFG_SYS_UBOOT_BASE \
|
|
(QSPI0_AMBA_BASE + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512)
|
|
|
|
#ifdef CONFIG_SPL_BUILD
|
|
/* malloc f used before GD_FLG_FULL_MALLOC_INIT set */
|
|
#define CFG_MALLOC_F_ADDR 0x930000
|
|
/* For RAW image gives a error info not panic */
|
|
#endif
|
|
|
|
#define MEM_LAYOUT_ENV_SETTINGS \
|
|
"fdt_addr_r=0x50200000\0" \
|
|
"kernel_addr_r=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
|
|
"kernel_comp_addr_r=0x40200000\0" \
|
|
"kernel_comp_size=0x08000000\0" \
|
|
"ramdisk_addr_r=0x50300000\0" \
|
|
"scriptaddr=0x50280000\0"
|
|
|
|
/* Enable Distro Boot */
|
|
#define BOOT_TARGET_DEVICES(func) \
|
|
func(MMC, mmc, 1) \
|
|
func(MMC, mmc, 0) \
|
|
func(DHCP, dhcp, na)
|
|
#include <config_distro_bootcmd.h>
|
|
|
|
/* Initial environment variables */
|
|
#define CFG_EXTRA_ENV_SETTINGS \
|
|
BOOTENV \
|
|
MEM_LAYOUT_ENV_SETTINGS \
|
|
"boot_file=Image\0" \
|
|
"boot_script_dhcp=boot.scr\0" \
|
|
"console=ttymxc0\0" \
|
|
"fdt_board=dev\0" \
|
|
"initrd_addr=0x43800000\0" \
|
|
"initrd_high=0xffffffffffffffff\0" \
|
|
"setup=setenv setupargs console=tty1 console=${console},${baudrate} " \
|
|
"consoleblank=0 earlycon\0" \
|
|
"update_uboot=askenv confirm Did you load flash.bin (y/N)?; " \
|
|
"if test \"$confirm\" = \"y\"; then " \
|
|
"setexpr blkcnt ${filesize} + 0x1ff && setexpr blkcnt " \
|
|
"${blkcnt} / 0x200; mmc dev 0 1; mmc write ${loadaddr} 0x2 " \
|
|
"${blkcnt}; fi\0"
|
|
|
|
#define CFG_SYS_INIT_RAM_ADDR 0x40000000
|
|
#define CFG_SYS_INIT_RAM_SIZE SZ_2M
|
|
|
|
#if defined(CONFIG_ENV_IS_IN_MMC)
|
|
/* Environment in eMMC, before config block at the end of 1st "boot sector" */
|
|
#endif
|
|
|
|
#define CFG_SYS_SDRAM_BASE 0x40000000
|
|
|
|
/* SDRAM configuration */
|
|
#define PHYS_SDRAM 0x40000000
|
|
#define PHYS_SDRAM_SIZE SZ_2G /* 2GB DDR */
|
|
|
|
/* USB Configs */
|
|
#define CFG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
|
|
|
|
#endif /* __VERDIN_IMX8MM_H */
|