mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-30 06:53:09 +00:00
6e73bb7e40
- In DM Ethernet, the old "egiga0" name is no longer valid, so replace it with Ethernet PHY name from device tree. Also, Ethernet PHY address is available so read it from device tree. Signed-off-by: Tony Dinh <mibodhi@gmail.com>
166 lines
3.4 KiB
C
166 lines
3.4 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright (C) 2021 Tony Dinh <mibodhi@gmail.com>
|
|
* (C) Copyright 2009
|
|
* Marvell Semiconductor <www.marvell.com>
|
|
* Written-by: Prafulla Wadaskar <prafulla@marvell.com>
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <init.h>
|
|
#include <miiphy.h>
|
|
#include <net.h>
|
|
#include <asm/global_data.h>
|
|
#include <asm/mach-types.h>
|
|
#include <asm/arch/cpu.h>
|
|
#include <asm/arch/soc.h>
|
|
#include <asm/arch/mpp.h>
|
|
#include "sheevaplug.h"
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
/*
|
|
* default gpio configuration
|
|
* There are maximum 64 gpios controlled through 2 sets of registers
|
|
* the below configuration configures mainly initial LED status
|
|
*/
|
|
mvebu_config_gpio(SHEEVAPLUG_OE_VAL_LOW,
|
|
SHEEVAPLUG_OE_VAL_HIGH,
|
|
SHEEVAPLUG_OE_LOW, SHEEVAPLUG_OE_HIGH);
|
|
|
|
/* Multi-Purpose Pins Functionality configuration */
|
|
static const u32 kwmpp_config[] = {
|
|
MPP0_NF_IO2,
|
|
MPP1_NF_IO3,
|
|
MPP2_NF_IO4,
|
|
MPP3_NF_IO5,
|
|
MPP4_NF_IO6,
|
|
MPP5_NF_IO7,
|
|
MPP6_SYSRST_OUTn,
|
|
MPP7_GPO,
|
|
MPP8_UART0_RTS,
|
|
MPP9_UART0_CTS,
|
|
MPP10_UART0_TXD,
|
|
MPP11_UART0_RXD,
|
|
MPP12_SD_CLK,
|
|
MPP13_SD_CMD,
|
|
MPP14_SD_D0,
|
|
MPP15_SD_D1,
|
|
MPP16_SD_D2,
|
|
MPP17_SD_D3,
|
|
MPP18_NF_IO0,
|
|
MPP19_NF_IO1,
|
|
MPP20_GPIO,
|
|
MPP21_GPIO,
|
|
MPP22_GPIO,
|
|
MPP23_GPIO,
|
|
MPP24_GPIO,
|
|
MPP25_GPIO,
|
|
MPP26_GPIO,
|
|
MPP27_GPIO,
|
|
MPP28_GPIO,
|
|
MPP29_TSMP9,
|
|
MPP30_GPIO,
|
|
MPP31_GPIO,
|
|
MPP32_GPIO,
|
|
MPP33_GPIO,
|
|
MPP34_GPIO,
|
|
MPP35_GPIO,
|
|
MPP36_GPIO,
|
|
MPP37_GPIO,
|
|
MPP38_GPIO,
|
|
MPP39_GPIO,
|
|
MPP40_GPIO,
|
|
MPP41_GPIO,
|
|
MPP42_GPIO,
|
|
MPP43_GPIO,
|
|
MPP44_GPIO,
|
|
MPP45_GPIO,
|
|
MPP46_GPIO,
|
|
MPP47_GPIO,
|
|
MPP48_GPIO,
|
|
MPP49_GPIO,
|
|
0
|
|
};
|
|
kirkwood_mpp_conf(kwmpp_config, NULL);
|
|
return 0;
|
|
}
|
|
|
|
int board_init(void)
|
|
{
|
|
/*
|
|
* arch number of board
|
|
*/
|
|
gd->bd->bi_arch_number = MACH_TYPE_SHEEVAPLUG;
|
|
|
|
/* adress of boot parameters */
|
|
gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int fdt_get_phy_addr(const char *path)
|
|
{
|
|
const void *fdt = gd->fdt_blob;
|
|
const u32 *reg;
|
|
const u32 *val;
|
|
int node, phandle, addr;
|
|
|
|
/* Find the node by its full path */
|
|
node = fdt_path_offset(fdt, path);
|
|
if (node >= 0) {
|
|
/* Look up phy-handle */
|
|
val = fdt_getprop(fdt, node, "phy-handle", NULL);
|
|
if (val) {
|
|
phandle = fdt32_to_cpu(*val);
|
|
if (!phandle)
|
|
return -1;
|
|
/* Follow it to its node */
|
|
node = fdt_node_offset_by_phandle(fdt, phandle);
|
|
if (node) {
|
|
/* Look up reg */
|
|
reg = fdt_getprop(fdt, node, "reg", NULL);
|
|
if (reg) {
|
|
addr = fdt32_to_cpu(*reg);
|
|
return addr;
|
|
}
|
|
}
|
|
}
|
|
}
|
|
return -1;
|
|
}
|
|
|
|
#ifdef CONFIG_RESET_PHY_R
|
|
/* Configure and enable MV88E1116 PHY */
|
|
void reset_phy(void)
|
|
{
|
|
u16 reg;
|
|
int phyaddr;
|
|
char *name = "ethernet-controller@72000";
|
|
char *eth0_path = "/ocp@f1000000/ethernet-controller@72000/ethernet0-port@0";
|
|
|
|
if (miiphy_set_current_dev(name))
|
|
return;
|
|
|
|
phyaddr = fdt_get_phy_addr(eth0_path);
|
|
if (phyaddr < 0)
|
|
return;
|
|
|
|
/*
|
|
* Enable RGMII delay on Tx and Rx for CPU port
|
|
* Ref: sec 4.7.2 of chip datasheet
|
|
*/
|
|
miiphy_write(name, phyaddr, MV88E1116_PGADR_REG, 2);
|
|
miiphy_read(name, phyaddr, MV88E1116_MAC_CTRL_REG, ®);
|
|
reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
|
|
miiphy_write(name, phyaddr, MV88E1116_MAC_CTRL_REG, reg);
|
|
miiphy_write(name, phyaddr, MV88E1116_PGADR_REG, 0);
|
|
|
|
/* reset the phy */
|
|
miiphy_reset(name, phyaddr);
|
|
|
|
printf("88E1116 Initialized on %s\n", name);
|
|
}
|
|
#endif /* CONFIG_RESET_PHY_R */
|