mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-17 00:33:06 +00:00
647ba68841
This is a preliminary documentation introducing different boot sequences, and notably the recovery mode. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> Reviewed-by: Simon Glass <sjg@chromium.org> Link: https://lore.kernel.org/r/20220706093649.3261229-1-narmstrong@baylibre.com
134 lines
6.6 KiB
ReStructuredText
134 lines
6.6 KiB
ReStructuredText
.. SPDX-License-Identifier: GPL-2.0+
|
|
|
|
Amlogic SoC Boot Flow
|
|
=====================
|
|
|
|
The Amlogic SoCs have a pre-defined boot sequence in the SoC ROM code. Here are
|
|
the possible boot sources of different SoC families supported by U-Boot:
|
|
|
|
GX* & AXG family
|
|
----------------
|
|
|
|
+----------+--------------------+-------+-------+---------------+---------------+
|
|
| | 1 | 2 | 3 | 4 | 5 |
|
|
+==========+====================+=======+=======+===============+===============+
|
|
| S905 | POC=0: SPI NOR | eMMC | NAND | SD Card | USB Device |
|
|
| S905X | | | | | |
|
|
| S905L | | | | | |
|
|
| S905W | | | | | |
|
|
| S912 | | | | | |
|
|
+----------+--------------------+-------+-------+---------------+---------------+
|
|
| S805X | POC=0: SPI NOR | eMMC | NAND | USB Device | - |
|
|
| A113D | | | | | |
|
|
| A113X | | | | | |
|
|
+----------+--------------------+-------+-------+---------------+---------------+
|
|
|
|
POC pin: `NAND_CLE`
|
|
|
|
Some boards provide a button to force USB BOOT which disables the eMMC clock signal
|
|
to bypass the eMMC stage. Others have removable eMMC modules; removing the eMMC and
|
|
SDCard will allow boot from USB.
|
|
|
|
An exception is the lafrite board (aml-s805x-xx) which has no SDCard slot and boots
|
|
from SPI. The only ways to boot the lafrite board from USB are:
|
|
|
|
- Erase the first sectors of SPI NOR flash
|
|
- Insert an HDMI boot plug forcing boot over USB
|
|
|
|
The VIM1 and initial VIM2 boards provide a test point on the eMMC signals to block
|
|
the storage from answering and continue to the next boot step.
|
|
|
|
The USB Device boot uses the first USB interface. On some boards this port is only
|
|
available on an USB-A type connector and needs an special Type-A to Type-A cable to
|
|
communicate with the BootROM.
|
|
|
|
G12* & SM1 family
|
|
-----------------
|
|
|
|
+-------+-------+-------+---------------+---------------+---------------+---------------+
|
|
| POC0 | POC1 | POC2 | 1 | 2 | 3 | 4 |
|
|
+=======+=======+=======+===============+===============+===============+===============+
|
|
| 0 | 0 | 0 | USB Device | SPI NOR | NAND/eMMC | SDCard |
|
|
+-------+-------+-------+---------------+---------------+---------------+---------------+
|
|
| 0 | 0 | 1 | USB Device | NAND/eMMC | SDCard | - |
|
|
+-------+-------+-------+---------------+---------------+---------------+---------------+
|
|
| 0 | 1 | 0 | SPI NOR | NAND/eMMC | SDCard | USB Device |
|
|
+-------+-------+-------+---------------+---------------+---------------+---------------+
|
|
| 0 | 1 | 1 | SPI NAND | NAND/eMMC | USB Device | - |
|
|
+-------+-------+-------+---------------+---------------+---------------+---------------+
|
|
| 1 | 0 | 0 | USB Device | SPI NOR | NAND/eMMC | SDCard |
|
|
+-------+-------+-------+---------------+---------------+---------------+---------------+
|
|
| 1 | 0 | 1 | USB Device | NAND/eMMC | SDCard | - |
|
|
+-------+-------+-------+---------------+---------------+---------------+---------------+
|
|
| 1 | 1 | 0 | SPI NOR | NAND/eMMC | SDCard | USB Device |
|
|
+-------+-------+-------+---------------+---------------+---------------+---------------+
|
|
| 1 | 1 | 1 | NAND/eMMC | SDCard | USB Device | - |
|
|
+-------+-------+-------+---------------+---------------+---------------+---------------+
|
|
|
|
The last option (1/1/1) is the normal default seen on production devices.
|
|
|
|
* POC0 pin: `BOOT_4` (0 and all other 1 means SPI NAND boot first)
|
|
* POC1 pin: `BOOT_5` (0 and all other 1 means USB Device boot first
|
|
* POC2 pin: `BOOT_6` (0 and all other 1 means SPI NOR boot first)
|
|
|
|
Most boards provide a button to force USB BOOT which lowers `BOOT_5` to 0. Some boards
|
|
provide a test point on the eMMC or SPI NOR clock signals to block the storage from
|
|
answering and continue to the next boot step.
|
|
|
|
The Khadas VIM3/3L boards embed a microcontroller which sets POC signals according
|
|
to its configuration or a specific key press sequence to either boot from SPI NOR
|
|
or eMMC then SDCard, or boot as an USB Device.
|
|
|
|
The Odroid N2/N2+ has a hardware switch to select between SPI NOR or eMMC boot.
|
|
|
|
Boot Modes
|
|
----------
|
|
|
|
* SDCard
|
|
|
|
The BootROM fetches the first SDCard sectors in one sequence, then checks the content
|
|
of the data. The BootROM expects to find the FIP binary in sector 1, 512 bytes offset
|
|
from the start.
|
|
|
|
* eMMC
|
|
|
|
The BootROM fetches the first sectors in one sequence, first on the main partition,
|
|
and then on the Boot0 followed by Boot1 HW partitions. After each read, the BootROM
|
|
checks the data and looks to the next partition if it fails. The BootROM expects to
|
|
find the FIP binary in sector 1, 512 bytes offset from the start.
|
|
|
|
* SPI NOR
|
|
|
|
The BootROM fetches the first SPI NOR sectors in one sequence, then checks the content
|
|
of the data. The BootROM expects to find the FIP binary in sector 1, 512 bytes offset
|
|
from the start.
|
|
|
|
* NAND & SPI NAND
|
|
|
|
These modes are rarely used in open platforms and no details are available.
|
|
|
|
* USB Device
|
|
|
|
The BootROM sets the USB Gadget interface to serve a custom USB protocol with the
|
|
USB ID 1b8e:c003. The Amlogic `update` utility is designed to use this protocol. It
|
|
is also implemented in the Amlogic Vendor U-Boot.
|
|
|
|
The open-source `pyamlboot` utility https://github.com/superna9999/pyamlboot also
|
|
implements this protocol and can load U-Boot in memory in order to start the SoC
|
|
without any attached storage or to recover from a failed/incorrect image flash.
|
|
|
|
HDMI Recovery
|
|
-------------
|
|
|
|
The BootROM also briefly reads 8 bytes at address I2C 0x52 offset 0xf8 (248) on the
|
|
HDMI DDC bus. If the content is `boot@USB` it will force USB boot mode. If the content
|
|
is `boot@SDC` it will force SDCard boot mode.
|
|
|
|
If USB Device doesn't enumerate or SD Card boot step doesn't work, the BootROM will
|
|
continue with the normal boot sequence.
|
|
|
|
Special boot dongles can be built by connecting a 256bytes EEPROM set to answer on
|
|
address 0x52, and program `boot@USB` or `boot@SDC` at offset 0xf8 (248).
|
|
|
|
Note: If the SoC is booted with USB Device forced at first step, it will keep the boot
|
|
order on warm reboot. Only cold reboot (power removed) will reset the boot order.
|