u-boot/include/configs/omap3_pandora.h
Adam Ford daa0f0500f Convert CONFIG_SYS_I2C_OMAP24XX to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_I2C_OMAP24XX

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2017-08-10 12:02:32 +02:00

109 lines
2.7 KiB
C

/*
* (C) Copyright 2008-2010
* Gražvydas Ignotas <notasas@gmail.com>
*
* Configuration settings for the OMAP3 Pandora.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#define CONFIG_NAND
/* override base for compatibility with MLO the device ships with */
#define CONFIG_SYS_TEXT_BASE 0x80008000
#include <configs/ti_omap3_common.h>
#define CONFIG_MISC_INIT_R
#define CONFIG_REVISION_TAG 1
#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
#define CONFIG_SYS_DEVICE_NULLDEV 1
/*
* Hardware drivers
*/
/* TWL4030 LED */
#define CONFIG_TWL4030_LED
/*
* NS16550 Configuration
*/
#undef CONFIG_SYS_NS16550_CLK
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE (-4)
#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3
#define CONFIG_SERIAL3 3
/* commands to include */
/*
* Board NAND Info.
*/
#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
/* to access nand */
#define CONFIG_SYS_NAND_BUSWIDTH_16BIT
#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_SW
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
#define CONFIG_SYS_NAND_OOBSIZE 64
#ifdef CONFIG_NAND
#define CONFIG_MTD_PARTITIONS /* required for UBI partition support */
#define MTDIDS_DEFAULT "nand0=omap2-nand.0"
#define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:512k(xloader),"\
"1920k(uboot),128k(uboot-env),"\
"10m(boot),-(rootfs)"
#else
#define MTDPARTS_DEFAULT
#endif
#define CONFIG_BOOTCOMMAND \
"run distro_bootcmd; " \
"setenv bootargs ${bootargs_ubi}; " \
"if mmc rescan && load mmc 0:1 ${loadaddr} autoboot.scr; then " \
"source ${loadaddr}; " \
"fi; " \
"ubi part boot && ubifsmount ubi:boot && " \
"ubifsload ${loadaddr} uImage && bootm ${loadaddr}"
#define BOOT_TARGET_DEVICES(func) \
func(MMC, mmc, 0) \
#include <config_distro_bootcmd.h>
#define CONFIG_EXTRA_ENV_SETTINGS \
DEFAULT_LINUX_BOOT_ENV \
"usbtty=cdc_acm\0" \
"bootargs_ubi=ubi.mtd=4 ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs " \
"rw rootflags=bulk_read vram=6272K omapfb.vram=0:3000K\0" \
"mtdparts=" MTDPARTS_DEFAULT "\0" \
BOOTENV \
/* memtest works on */
#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0)
#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
0x01F00000) /* 31MB */
#if defined(CONFIG_NAND)
#define CONFIG_SYS_FLASH_BASE NAND_BASE
#endif
/* Monitor at start of flash */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
#endif /* __CONFIG_H */