mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-11 22:03:15 +00:00
dfd4861c22
The DIGPROG register map: 23 ------- 16 | 15 ------ 8 | 7 --- 0 | Major upper | Major Lower | Minor | We also need to account for Major Lower. Signed-off-by: Ye.Li <B37916@freescale.com> Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
665 lines
16 KiB
C
665 lines
16 KiB
C
/*
|
|
* (C) Copyright 2007
|
|
* Sascha Hauer, Pengutronix
|
|
*
|
|
* (C) Copyright 2009 Freescale Semiconductor, Inc.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <asm/armv7.h>
|
|
#include <asm/bootm.h>
|
|
#include <asm/pl310.h>
|
|
#include <asm/errno.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/imx-regs.h>
|
|
#include <asm/arch/clock.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <asm/imx-common/boot_mode.h>
|
|
#include <asm/imx-common/dma.h>
|
|
#include <stdbool.h>
|
|
#include <asm/arch/mxc_hdmi.h>
|
|
#include <asm/arch/crm_regs.h>
|
|
#include <dm.h>
|
|
#include <imx_thermal.h>
|
|
|
|
enum ldo_reg {
|
|
LDO_ARM,
|
|
LDO_SOC,
|
|
LDO_PU,
|
|
};
|
|
|
|
struct scu_regs {
|
|
u32 ctrl;
|
|
u32 config;
|
|
u32 status;
|
|
u32 invalidate;
|
|
u32 fpga_rev;
|
|
};
|
|
|
|
#if defined(CONFIG_IMX6_THERMAL)
|
|
static const struct imx_thermal_plat imx6_thermal_plat = {
|
|
.regs = (void *)ANATOP_BASE_ADDR,
|
|
.fuse_bank = 1,
|
|
.fuse_word = 6,
|
|
};
|
|
|
|
U_BOOT_DEVICE(imx6_thermal) = {
|
|
.name = "imx_thermal",
|
|
.platdata = &imx6_thermal_plat,
|
|
};
|
|
#endif
|
|
|
|
u32 get_nr_cpus(void)
|
|
{
|
|
struct scu_regs *scu = (struct scu_regs *)SCU_BASE_ADDR;
|
|
return readl(&scu->config) & 3;
|
|
}
|
|
|
|
u32 get_cpu_rev(void)
|
|
{
|
|
struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR;
|
|
u32 reg = readl(&anatop->digprog_sololite);
|
|
u32 type = ((reg >> 16) & 0xff);
|
|
u32 major;
|
|
|
|
if (type != MXC_CPU_MX6SL) {
|
|
reg = readl(&anatop->digprog);
|
|
struct scu_regs *scu = (struct scu_regs *)SCU_BASE_ADDR;
|
|
u32 cfg = readl(&scu->config) & 3;
|
|
type = ((reg >> 16) & 0xff);
|
|
if (type == MXC_CPU_MX6DL) {
|
|
if (!cfg)
|
|
type = MXC_CPU_MX6SOLO;
|
|
}
|
|
|
|
if (type == MXC_CPU_MX6Q) {
|
|
if (cfg == 1)
|
|
type = MXC_CPU_MX6D;
|
|
}
|
|
|
|
}
|
|
major = ((reg >> 8) & 0xff);
|
|
reg &= 0xff; /* mx6 silicon revision */
|
|
return (type << 12) | (reg + (0x10 * (major + 1)));
|
|
}
|
|
|
|
/*
|
|
* OCOTP_CFG3[17:16] (see Fusemap Description Table offset 0x440)
|
|
* defines a 2-bit SPEED_GRADING
|
|
*/
|
|
#define OCOTP_CFG3_SPEED_SHIFT 16
|
|
#define OCOTP_CFG3_SPEED_800MHZ 0
|
|
#define OCOTP_CFG3_SPEED_850MHZ 1
|
|
#define OCOTP_CFG3_SPEED_1GHZ 2
|
|
#define OCOTP_CFG3_SPEED_1P2GHZ 3
|
|
|
|
u32 get_cpu_speed_grade_hz(void)
|
|
{
|
|
struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR;
|
|
struct fuse_bank *bank = &ocotp->bank[0];
|
|
struct fuse_bank0_regs *fuse =
|
|
(struct fuse_bank0_regs *)bank->fuse_regs;
|
|
uint32_t val;
|
|
|
|
val = readl(&fuse->cfg3);
|
|
val >>= OCOTP_CFG3_SPEED_SHIFT;
|
|
val &= 0x3;
|
|
|
|
switch (val) {
|
|
/* Valid for IMX6DQ */
|
|
case OCOTP_CFG3_SPEED_1P2GHZ:
|
|
if (is_cpu_type(MXC_CPU_MX6Q) || is_cpu_type(MXC_CPU_MX6D))
|
|
return 1200000000;
|
|
/* Valid for IMX6SX/IMX6SDL/IMX6DQ */
|
|
case OCOTP_CFG3_SPEED_1GHZ:
|
|
return 996000000;
|
|
/* Valid for IMX6DQ */
|
|
case OCOTP_CFG3_SPEED_850MHZ:
|
|
if (is_cpu_type(MXC_CPU_MX6Q) || is_cpu_type(MXC_CPU_MX6D))
|
|
return 852000000;
|
|
/* Valid for IMX6SX/IMX6SDL/IMX6DQ */
|
|
case OCOTP_CFG3_SPEED_800MHZ:
|
|
return 792000000;
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* OCOTP_MEM0[7:6] (see Fusemap Description Table offset 0x480)
|
|
* defines a 2-bit Temperature Grade
|
|
*
|
|
* return temperature grade and min/max temperature in celcius
|
|
*/
|
|
#define OCOTP_MEM0_TEMP_SHIFT 6
|
|
|
|
u32 get_cpu_temp_grade(int *minc, int *maxc)
|
|
{
|
|
struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR;
|
|
struct fuse_bank *bank = &ocotp->bank[1];
|
|
struct fuse_bank1_regs *fuse =
|
|
(struct fuse_bank1_regs *)bank->fuse_regs;
|
|
uint32_t val;
|
|
|
|
val = readl(&fuse->mem0);
|
|
val >>= OCOTP_MEM0_TEMP_SHIFT;
|
|
val &= 0x3;
|
|
|
|
if (minc && maxc) {
|
|
if (val == TEMP_AUTOMOTIVE) {
|
|
*minc = -40;
|
|
*maxc = 125;
|
|
} else if (val == TEMP_INDUSTRIAL) {
|
|
*minc = -40;
|
|
*maxc = 105;
|
|
} else if (val == TEMP_EXTCOMMERCIAL) {
|
|
*minc = -20;
|
|
*maxc = 105;
|
|
} else {
|
|
*minc = 0;
|
|
*maxc = 95;
|
|
}
|
|
}
|
|
return val;
|
|
}
|
|
|
|
#ifdef CONFIG_REVISION_TAG
|
|
u32 __weak get_board_rev(void)
|
|
{
|
|
u32 cpurev = get_cpu_rev();
|
|
u32 type = ((cpurev >> 12) & 0xff);
|
|
if (type == MXC_CPU_MX6SOLO)
|
|
cpurev = (MXC_CPU_MX6DL) << 12 | (cpurev & 0xFFF);
|
|
|
|
if (type == MXC_CPU_MX6D)
|
|
cpurev = (MXC_CPU_MX6Q) << 12 | (cpurev & 0xFFF);
|
|
|
|
return cpurev;
|
|
}
|
|
#endif
|
|
|
|
void init_aips(void)
|
|
{
|
|
struct aipstz_regs *aips1, *aips2;
|
|
#ifdef CONFIG_MX6SX
|
|
struct aipstz_regs *aips3;
|
|
#endif
|
|
|
|
aips1 = (struct aipstz_regs *)AIPS1_BASE_ADDR;
|
|
aips2 = (struct aipstz_regs *)AIPS2_BASE_ADDR;
|
|
#ifdef CONFIG_MX6SX
|
|
aips3 = (struct aipstz_regs *)AIPS3_CONFIG_BASE_ADDR;
|
|
#endif
|
|
|
|
/*
|
|
* Set all MPROTx to be non-bufferable, trusted for R/W,
|
|
* not forced to user-mode.
|
|
*/
|
|
writel(0x77777777, &aips1->mprot0);
|
|
writel(0x77777777, &aips1->mprot1);
|
|
writel(0x77777777, &aips2->mprot0);
|
|
writel(0x77777777, &aips2->mprot1);
|
|
|
|
/*
|
|
* Set all OPACRx to be non-bufferable, not require
|
|
* supervisor privilege level for access,allow for
|
|
* write access and untrusted master access.
|
|
*/
|
|
writel(0x00000000, &aips1->opacr0);
|
|
writel(0x00000000, &aips1->opacr1);
|
|
writel(0x00000000, &aips1->opacr2);
|
|
writel(0x00000000, &aips1->opacr3);
|
|
writel(0x00000000, &aips1->opacr4);
|
|
writel(0x00000000, &aips2->opacr0);
|
|
writel(0x00000000, &aips2->opacr1);
|
|
writel(0x00000000, &aips2->opacr2);
|
|
writel(0x00000000, &aips2->opacr3);
|
|
writel(0x00000000, &aips2->opacr4);
|
|
|
|
#ifdef CONFIG_MX6SX
|
|
/*
|
|
* Set all MPROTx to be non-bufferable, trusted for R/W,
|
|
* not forced to user-mode.
|
|
*/
|
|
writel(0x77777777, &aips3->mprot0);
|
|
writel(0x77777777, &aips3->mprot1);
|
|
|
|
/*
|
|
* Set all OPACRx to be non-bufferable, not require
|
|
* supervisor privilege level for access,allow for
|
|
* write access and untrusted master access.
|
|
*/
|
|
writel(0x00000000, &aips3->opacr0);
|
|
writel(0x00000000, &aips3->opacr1);
|
|
writel(0x00000000, &aips3->opacr2);
|
|
writel(0x00000000, &aips3->opacr3);
|
|
writel(0x00000000, &aips3->opacr4);
|
|
#endif
|
|
}
|
|
|
|
static void clear_ldo_ramp(void)
|
|
{
|
|
struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR;
|
|
int reg;
|
|
|
|
/* ROM may modify LDO ramp up time according to fuse setting, so in
|
|
* order to be in the safe side we neeed to reset these settings to
|
|
* match the reset value: 0'b00
|
|
*/
|
|
reg = readl(&anatop->ana_misc2);
|
|
reg &= ~(0x3f << 24);
|
|
writel(reg, &anatop->ana_misc2);
|
|
}
|
|
|
|
/*
|
|
* Set the PMU_REG_CORE register
|
|
*
|
|
* Set LDO_SOC/PU/ARM regulators to the specified millivolt level.
|
|
* Possible values are from 0.725V to 1.450V in steps of
|
|
* 0.025V (25mV).
|
|
*/
|
|
static int set_ldo_voltage(enum ldo_reg ldo, u32 mv)
|
|
{
|
|
struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR;
|
|
u32 val, step, old, reg = readl(&anatop->reg_core);
|
|
u8 shift;
|
|
|
|
if (mv < 725)
|
|
val = 0x00; /* Power gated off */
|
|
else if (mv > 1450)
|
|
val = 0x1F; /* Power FET switched full on. No regulation */
|
|
else
|
|
val = (mv - 700) / 25;
|
|
|
|
clear_ldo_ramp();
|
|
|
|
switch (ldo) {
|
|
case LDO_SOC:
|
|
shift = 18;
|
|
break;
|
|
case LDO_PU:
|
|
shift = 9;
|
|
break;
|
|
case LDO_ARM:
|
|
shift = 0;
|
|
break;
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
|
|
old = (reg & (0x1F << shift)) >> shift;
|
|
step = abs(val - old);
|
|
if (step == 0)
|
|
return 0;
|
|
|
|
reg = (reg & ~(0x1F << shift)) | (val << shift);
|
|
writel(reg, &anatop->reg_core);
|
|
|
|
/*
|
|
* The LDO ramp-up is based on 64 clock cycles of 24 MHz = 2.6 us per
|
|
* step
|
|
*/
|
|
udelay(3 * step);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void imx_set_wdog_powerdown(bool enable)
|
|
{
|
|
struct wdog_regs *wdog1 = (struct wdog_regs *)WDOG1_BASE_ADDR;
|
|
struct wdog_regs *wdog2 = (struct wdog_regs *)WDOG2_BASE_ADDR;
|
|
|
|
#ifdef CONFIG_MX6SX
|
|
struct wdog_regs *wdog3 = (struct wdog_regs *)WDOG3_BASE_ADDR;
|
|
writew(enable, &wdog3->wmcr);
|
|
#endif
|
|
|
|
/* Write to the PDE (Power Down Enable) bit */
|
|
writew(enable, &wdog1->wmcr);
|
|
writew(enable, &wdog2->wmcr);
|
|
}
|
|
|
|
static void set_ahb_rate(u32 val)
|
|
{
|
|
struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
|
|
u32 reg, div;
|
|
|
|
div = get_periph_clk() / val - 1;
|
|
reg = readl(&mxc_ccm->cbcdr);
|
|
|
|
writel((reg & (~MXC_CCM_CBCDR_AHB_PODF_MASK)) |
|
|
(div << MXC_CCM_CBCDR_AHB_PODF_OFFSET), &mxc_ccm->cbcdr);
|
|
}
|
|
|
|
static void clear_mmdc_ch_mask(void)
|
|
{
|
|
struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
|
|
|
|
/* Clear MMDC channel mask */
|
|
writel(0, &mxc_ccm->ccdr);
|
|
}
|
|
|
|
static void init_bandgap(void)
|
|
{
|
|
struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR;
|
|
/*
|
|
* Ensure the bandgap has stabilized.
|
|
*/
|
|
while (!(readl(&anatop->ana_misc0) & 0x80))
|
|
;
|
|
/*
|
|
* For best noise performance of the analog blocks using the
|
|
* outputs of the bandgap, the reftop_selfbiasoff bit should
|
|
* be set.
|
|
*/
|
|
writel(BM_ANADIG_ANA_MISC0_REFTOP_SELBIASOFF, &anatop->ana_misc0_set);
|
|
}
|
|
|
|
|
|
#ifdef CONFIG_MX6SL
|
|
static void set_preclk_from_osc(void)
|
|
{
|
|
struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
|
|
u32 reg;
|
|
|
|
reg = readl(&mxc_ccm->cscmr1);
|
|
reg |= MXC_CCM_CSCMR1_PER_CLK_SEL_MASK;
|
|
writel(reg, &mxc_ccm->cscmr1);
|
|
}
|
|
#endif
|
|
|
|
#define SRC_SCR_WARM_RESET_ENABLE 0
|
|
|
|
static void init_src(void)
|
|
{
|
|
struct src *src_regs = (struct src *)SRC_BASE_ADDR;
|
|
u32 val;
|
|
|
|
/*
|
|
* force warm reset sources to generate cold reset
|
|
* for a more reliable restart
|
|
*/
|
|
val = readl(&src_regs->scr);
|
|
val &= ~(1 << SRC_SCR_WARM_RESET_ENABLE);
|
|
writel(val, &src_regs->scr);
|
|
}
|
|
|
|
int arch_cpu_init(void)
|
|
{
|
|
init_aips();
|
|
|
|
/* Need to clear MMDC_CHx_MASK to make warm reset work. */
|
|
clear_mmdc_ch_mask();
|
|
|
|
/*
|
|
* Disable self-bias circuit in the analog bandap.
|
|
* The self-bias circuit is used by the bandgap during startup.
|
|
* This bit should be set after the bandgap has initialized.
|
|
*/
|
|
init_bandgap();
|
|
|
|
/*
|
|
* When low freq boot is enabled, ROM will not set AHB
|
|
* freq, so we need to ensure AHB freq is 132MHz in such
|
|
* scenario.
|
|
*/
|
|
if (mxc_get_clock(MXC_ARM_CLK) == 396000000)
|
|
set_ahb_rate(132000000);
|
|
|
|
/* Set perclk to source from OSC 24MHz */
|
|
#if defined(CONFIG_MX6SL)
|
|
set_preclk_from_osc();
|
|
#endif
|
|
|
|
imx_set_wdog_powerdown(false); /* Disable PDE bit of WMCR register */
|
|
|
|
#ifdef CONFIG_APBH_DMA
|
|
/* Start APBH DMA */
|
|
mxs_dma_init();
|
|
#endif
|
|
|
|
init_src();
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_postclk_init(void)
|
|
{
|
|
set_ldo_voltage(LDO_SOC, 1175); /* Set VDDSOC to 1.175V */
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifndef CONFIG_SYS_DCACHE_OFF
|
|
void enable_caches(void)
|
|
{
|
|
#if defined(CONFIG_SYS_ARM_CACHE_WRITETHROUGH)
|
|
enum dcache_option option = DCACHE_WRITETHROUGH;
|
|
#else
|
|
enum dcache_option option = DCACHE_WRITEBACK;
|
|
#endif
|
|
|
|
/* Avoid random hang when download by usb */
|
|
invalidate_dcache_all();
|
|
|
|
/* Enable D-cache. I-cache is already enabled in start.S */
|
|
dcache_enable();
|
|
|
|
/* Enable caching on OCRAM and ROM */
|
|
mmu_set_region_dcache_behaviour(ROMCP_ARB_BASE_ADDR,
|
|
ROMCP_ARB_END_ADDR,
|
|
option);
|
|
mmu_set_region_dcache_behaviour(IRAM_BASE_ADDR,
|
|
IRAM_SIZE,
|
|
option);
|
|
}
|
|
#endif
|
|
|
|
#if defined(CONFIG_FEC_MXC)
|
|
void imx_get_mac_from_fuse(int dev_id, unsigned char *mac)
|
|
{
|
|
struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR;
|
|
struct fuse_bank *bank = &ocotp->bank[4];
|
|
struct fuse_bank4_regs *fuse =
|
|
(struct fuse_bank4_regs *)bank->fuse_regs;
|
|
|
|
u32 value = readl(&fuse->mac_addr_high);
|
|
mac[0] = (value >> 8);
|
|
mac[1] = value ;
|
|
|
|
value = readl(&fuse->mac_addr_low);
|
|
mac[2] = value >> 24 ;
|
|
mac[3] = value >> 16 ;
|
|
mac[4] = value >> 8 ;
|
|
mac[5] = value ;
|
|
|
|
}
|
|
#endif
|
|
|
|
void boot_mode_apply(unsigned cfg_val)
|
|
{
|
|
unsigned reg;
|
|
struct src *psrc = (struct src *)SRC_BASE_ADDR;
|
|
writel(cfg_val, &psrc->gpr9);
|
|
reg = readl(&psrc->gpr10);
|
|
if (cfg_val)
|
|
reg |= 1 << 28;
|
|
else
|
|
reg &= ~(1 << 28);
|
|
writel(reg, &psrc->gpr10);
|
|
}
|
|
/*
|
|
* cfg_val will be used for
|
|
* Boot_cfg4[7:0]:Boot_cfg3[7:0]:Boot_cfg2[7:0]:Boot_cfg1[7:0]
|
|
* After reset, if GPR10[28] is 1, ROM will use GPR9[25:0]
|
|
* instead of SBMR1 to determine the boot device.
|
|
*/
|
|
const struct boot_mode soc_boot_modes[] = {
|
|
{"normal", MAKE_CFGVAL(0x00, 0x00, 0x00, 0x00)},
|
|
/* reserved value should start rom usb */
|
|
{"usb", MAKE_CFGVAL(0x01, 0x00, 0x00, 0x00)},
|
|
{"sata", MAKE_CFGVAL(0x20, 0x00, 0x00, 0x00)},
|
|
{"ecspi1:0", MAKE_CFGVAL(0x30, 0x00, 0x00, 0x08)},
|
|
{"ecspi1:1", MAKE_CFGVAL(0x30, 0x00, 0x00, 0x18)},
|
|
{"ecspi1:2", MAKE_CFGVAL(0x30, 0x00, 0x00, 0x28)},
|
|
{"ecspi1:3", MAKE_CFGVAL(0x30, 0x00, 0x00, 0x38)},
|
|
/* 4 bit bus width */
|
|
{"esdhc1", MAKE_CFGVAL(0x40, 0x20, 0x00, 0x00)},
|
|
{"esdhc2", MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)},
|
|
{"esdhc3", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
|
|
{"esdhc4", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)},
|
|
{NULL, 0},
|
|
};
|
|
|
|
void s_init(void)
|
|
{
|
|
struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR;
|
|
struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
|
|
u32 mask480;
|
|
u32 mask528;
|
|
u32 reg, periph1, periph2;
|
|
|
|
if (is_cpu_type(MXC_CPU_MX6SX))
|
|
return;
|
|
|
|
/* Due to hardware limitation, on MX6Q we need to gate/ungate all PFDs
|
|
* to make sure PFD is working right, otherwise, PFDs may
|
|
* not output clock after reset, MX6DL and MX6SL have added 396M pfd
|
|
* workaround in ROM code, as bus clock need it
|
|
*/
|
|
|
|
mask480 = ANATOP_PFD_CLKGATE_MASK(0) |
|
|
ANATOP_PFD_CLKGATE_MASK(1) |
|
|
ANATOP_PFD_CLKGATE_MASK(2) |
|
|
ANATOP_PFD_CLKGATE_MASK(3);
|
|
mask528 = ANATOP_PFD_CLKGATE_MASK(1) |
|
|
ANATOP_PFD_CLKGATE_MASK(3);
|
|
|
|
reg = readl(&ccm->cbcmr);
|
|
periph2 = ((reg & MXC_CCM_CBCMR_PRE_PERIPH2_CLK_SEL_MASK)
|
|
>> MXC_CCM_CBCMR_PRE_PERIPH2_CLK_SEL_OFFSET);
|
|
periph1 = ((reg & MXC_CCM_CBCMR_PRE_PERIPH_CLK_SEL_MASK)
|
|
>> MXC_CCM_CBCMR_PRE_PERIPH_CLK_SEL_OFFSET);
|
|
|
|
/* Checking if PLL2 PFD0 or PLL2 PFD2 is using for periph clock */
|
|
if ((periph2 != 0x2) && (periph1 != 0x2))
|
|
mask528 |= ANATOP_PFD_CLKGATE_MASK(0);
|
|
|
|
if ((periph2 != 0x1) && (periph1 != 0x1) &&
|
|
(periph2 != 0x3) && (periph1 != 0x3))
|
|
mask528 |= ANATOP_PFD_CLKGATE_MASK(2);
|
|
|
|
writel(mask480, &anatop->pfd_480_set);
|
|
writel(mask528, &anatop->pfd_528_set);
|
|
writel(mask480, &anatop->pfd_480_clr);
|
|
writel(mask528, &anatop->pfd_528_clr);
|
|
}
|
|
|
|
#ifdef CONFIG_IMX_HDMI
|
|
void imx_enable_hdmi_phy(void)
|
|
{
|
|
struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
|
|
u8 reg;
|
|
reg = readb(&hdmi->phy_conf0);
|
|
reg |= HDMI_PHY_CONF0_PDZ_MASK;
|
|
writeb(reg, &hdmi->phy_conf0);
|
|
udelay(3000);
|
|
reg |= HDMI_PHY_CONF0_ENTMDS_MASK;
|
|
writeb(reg, &hdmi->phy_conf0);
|
|
udelay(3000);
|
|
reg |= HDMI_PHY_CONF0_GEN2_TXPWRON_MASK;
|
|
writeb(reg, &hdmi->phy_conf0);
|
|
writeb(HDMI_MC_PHYRSTZ_ASSERT, &hdmi->mc_phyrstz);
|
|
}
|
|
|
|
void imx_setup_hdmi(void)
|
|
{
|
|
struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
|
|
struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
|
|
int reg;
|
|
|
|
/* Turn on HDMI PHY clock */
|
|
reg = readl(&mxc_ccm->CCGR2);
|
|
reg |= MXC_CCM_CCGR2_HDMI_TX_IAHBCLK_MASK|
|
|
MXC_CCM_CCGR2_HDMI_TX_ISFRCLK_MASK;
|
|
writel(reg, &mxc_ccm->CCGR2);
|
|
writeb(HDMI_MC_PHYRSTZ_DEASSERT, &hdmi->mc_phyrstz);
|
|
reg = readl(&mxc_ccm->chsccdr);
|
|
reg &= ~(MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK|
|
|
MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK|
|
|
MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK);
|
|
reg |= (CHSCCDR_PODF_DIVIDE_BY_3
|
|
<< MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET)
|
|
|(CHSCCDR_IPU_PRE_CLK_540M_PFD
|
|
<< MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET);
|
|
writel(reg, &mxc_ccm->chsccdr);
|
|
}
|
|
#endif
|
|
|
|
#ifndef CONFIG_SYS_L2CACHE_OFF
|
|
#define IOMUXC_GPR11_L2CACHE_AS_OCRAM 0x00000002
|
|
void v7_outer_cache_enable(void)
|
|
{
|
|
struct pl310_regs *const pl310 = (struct pl310_regs *)L2_PL310_BASE;
|
|
unsigned int val;
|
|
|
|
|
|
/*
|
|
* Set bit 22 in the auxiliary control register. If this bit
|
|
* is cleared, PL310 treats Normal Shared Non-cacheable
|
|
* accesses as Cacheable no-allocate.
|
|
*/
|
|
setbits_le32(&pl310->pl310_aux_ctrl, L310_SHARED_ATT_OVERRIDE_ENABLE);
|
|
|
|
#if defined CONFIG_MX6SL
|
|
struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
|
|
val = readl(&iomux->gpr[11]);
|
|
if (val & IOMUXC_GPR11_L2CACHE_AS_OCRAM) {
|
|
/* L2 cache configured as OCRAM, reset it */
|
|
val &= ~IOMUXC_GPR11_L2CACHE_AS_OCRAM;
|
|
writel(val, &iomux->gpr[11]);
|
|
}
|
|
#endif
|
|
|
|
/* Must disable the L2 before changing the latency parameters */
|
|
clrbits_le32(&pl310->pl310_ctrl, L2X0_CTRL_EN);
|
|
|
|
writel(0x132, &pl310->pl310_tag_latency_ctrl);
|
|
writel(0x132, &pl310->pl310_data_latency_ctrl);
|
|
|
|
val = readl(&pl310->pl310_prefetch_ctrl);
|
|
|
|
/* Turn on the L2 I/D prefetch */
|
|
val |= 0x30000000;
|
|
|
|
/*
|
|
* The L2 cache controller(PL310) version on the i.MX6D/Q is r3p1-50rel0
|
|
* The L2 cache controller(PL310) version on the i.MX6DL/SOLO/SL is r3p2
|
|
* But according to ARM PL310 errata: 752271
|
|
* ID: 752271: Double linefill feature can cause data corruption
|
|
* Fault Status: Present in: r3p0, r3p1, r3p1-50rel0. Fixed in r3p2
|
|
* Workaround: The only workaround to this erratum is to disable the
|
|
* double linefill feature. This is the default behavior.
|
|
*/
|
|
|
|
#ifndef CONFIG_MX6Q
|
|
val |= 0x40800000;
|
|
#endif
|
|
writel(val, &pl310->pl310_prefetch_ctrl);
|
|
|
|
val = readl(&pl310->pl310_power_ctrl);
|
|
val |= L2X0_DYNAMIC_CLK_GATING_EN;
|
|
val |= L2X0_STNDBY_MODE_EN;
|
|
writel(val, &pl310->pl310_power_ctrl);
|
|
|
|
setbits_le32(&pl310->pl310_ctrl, L2X0_CTRL_EN);
|
|
}
|
|
|
|
void v7_outer_cache_disable(void)
|
|
{
|
|
struct pl310_regs *const pl310 = (struct pl310_regs *)L2_PL310_BASE;
|
|
|
|
clrbits_le32(&pl310->pl310_ctrl, L2X0_CTRL_EN);
|
|
}
|
|
#endif /* !CONFIG_SYS_L2CACHE_OFF */
|