u-boot/include/configs/cm_t335.h
Tom Rini 871fd508fc Convert CONFIG_SYS_NAND_U_BOOT_LOCATIONS et al to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_NAND_U_BOOT_LOCATIONS
   CONFIG_SYS_NAND_U_BOOT_OFFS

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-06 09:16:24 -04:00

124 lines
3.2 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Config file for Compulab CM-T335 board
*
* Copyright (C) 2013, Compulab Ltd - http://compulab.co.il/
*
* Author: Ilya Ledvich <ilya@compulab.co.il>
*/
#ifndef __CONFIG_CM_T335_H
#define __CONFIG_CM_T335_H
#include <configs/ti_am335x_common.h>
#undef CONFIG_MAX_RAM_BANK_SIZE
#define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* 512MB */
/* Clock Defines */
#define V_OSCK 25000000 /* Clock output from T2 */
#define V_SCLK (V_OSCK)
#ifndef CONFIG_SPL_BUILD
#define MMCARGS \
"mmcdev=0\0" \
"mmcroot=/dev/mmcblk0p2 rw rootwait\0" \
"mmcrootfstype=ext4\0" \
"mmcargs=setenv bootargs console=${console} " \
"root=${mmcroot} " \
"rootfstype=${mmcrootfstype}\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"bootm ${loadaddr}\0"
#define NANDARGS \
"mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
"mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
"nandroot=ubi0:rootfs rw\0" \
"nandrootfstype=ubifs\0" \
"nandargs=setenv bootargs console=${console} " \
"root=${nandroot} " \
"rootfstype=${nandrootfstype} " \
"ubi.mtd=${rootfs_name}\0" \
"nandboot=echo Booting from nand ...; " \
"run nandargs; " \
"nboot ${loadaddr} nand0 900000; " \
"bootm ${loadaddr}\0"
#define CONFIG_EXTRA_ENV_SETTINGS \
"loadaddr=82000000\0" \
"console=ttyO0,115200n8\0" \
"rootfs_name=rootfs\0" \
"loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
"bootscript=echo Running bootscript from mmc ...; " \
"source ${loadaddr}\0" \
"loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
MMCARGS \
NANDARGS
#define CONFIG_BOOTCOMMAND \
"mmc dev ${mmcdev}; if mmc rescan; then " \
"if run loadbootscript; then " \
"run bootscript; " \
"else " \
"if run loaduimage; then " \
"run mmcboot; " \
"else run nandboot; " \
"fi; " \
"fi; " \
"else run nandboot; fi"
#endif /* CONFIG_SPL_BUILD */
#define CONFIG_TIMESTAMP
#define CONFIG_SYS_AUTOLOAD "no"
/* Serial console configuration */
/* NS16550 Configuration */
#define CONFIG_SYS_NS16550_COM1 0x44e09000 /* UART0 */
#define CONFIG_SYS_NS16550_COM2 0x48022000 /* UART1 */
/* I2C Configuration */
/* SPL */
/* Network. */
/* NAND support */
#define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, \
10, 11, 12, 13, 14, 15, 16, 17, \
18, 19, 20, 21, 22, 23, 24, 25, \
26, 27, 28, 29, 30, 31, 32, 33, \
34, 35, 36, 37, 38, 39, 40, 41, \
42, 43, 44, 45, 46, 47, 48, 49, \
50, 51, 52, 53, 54, 55, 56, 57, }
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 14
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
#ifdef CONFIG_SPL_OS_BOOT
#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x500000
#endif
/* GPIO pin + bank to pin ID mapping */
#define GPIO_PIN(_bank, _pin) ((_bank << 5) + _pin)
/* Status LED */
/* Status LED polarity is inversed, so init it in the "off" state */
/* EEPROM */
#ifndef CONFIG_SPL_BUILD
/*
* Enable PCA9555 at I2C0-0x26.
* First select the I2C0 bus with "i2c dev 0", then use "pca953x" command.
*/
#define CONFIG_PCA953X
#define CONFIG_SYS_I2C_PCA953X_ADDR 0x26
#define CONFIG_SYS_I2C_PCA953X_WIDTH { {0x26, 16} }
#endif /* CONFIG_SPL_BUILD */
#endif /* __CONFIG_CM_T335_H */