mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-11 07:34:31 +00:00
835a5559bd
In commit bb1f327 we removed the UHH reset to fix NFS root (over usb
ethernet) problems with Beagleboard (3530 ES1.0). However, this
seems to cause USB detection problems for Pandaboard, about (3/8).
On further investigation, it seems that doing the UHH reset is not
the cause of the original Beagleboard problem, but in the way the reset
was done.
This patch adds proper UHH RESET mechanism for OMAP3 and OMAP4/5 based
on the UHH_REVISION register. This should fix the Beagleboard NFS
problem as well as the Pandaboard USB detection problem.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
CC: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Roger Quadros <rogerq@ti.com>
295 lines
7.4 KiB
C
295 lines
7.4 KiB
C
/*
|
|
* (C) Copyright 2011 Ilya Yanok, Emcraft Systems
|
|
* (C) Copyright 2004-2008
|
|
* Texas Instruments, <www.ti.com>
|
|
*
|
|
* Derived from Beagle Board code by
|
|
* Sunil Kumar <sunilsaini05@gmail.com>
|
|
* Shashi Ranjan <shashiranjanmca05@gmail.com>
|
|
*
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <usb.h>
|
|
#include <usb/ulpi.h>
|
|
#include <errno.h>
|
|
#include <asm/io.h>
|
|
#include <asm/gpio.h>
|
|
#include <asm/arch/ehci.h>
|
|
#include <asm/ehci-omap.h>
|
|
|
|
#include "ehci.h"
|
|
|
|
static struct omap_uhh *const uhh = (struct omap_uhh *)OMAP_UHH_BASE;
|
|
static struct omap_usbtll *const usbtll = (struct omap_usbtll *)OMAP_USBTLL_BASE;
|
|
static struct omap_ehci *const ehci = (struct omap_ehci *)OMAP_EHCI_BASE;
|
|
|
|
static int omap_uhh_reset(void)
|
|
{
|
|
int timeout = 0;
|
|
u32 rev;
|
|
|
|
rev = readl(&uhh->rev);
|
|
|
|
/* Soft RESET */
|
|
writel(OMAP_UHH_SYSCONFIG_SOFTRESET, &uhh->sysc);
|
|
|
|
switch (rev) {
|
|
case OMAP_USBHS_REV1:
|
|
/* Wait for soft RESET to complete */
|
|
while (!(readl(&uhh->syss) & 0x1)) {
|
|
if (timeout > 100) {
|
|
printf("%s: RESET timeout\n", __func__);
|
|
return -1;
|
|
}
|
|
udelay(10);
|
|
timeout++;
|
|
}
|
|
|
|
/* Set No-Idle, No-Standby */
|
|
writel(OMAP_UHH_SYSCONFIG_VAL, &uhh->sysc);
|
|
break;
|
|
|
|
default: /* Rev. 2 onwards */
|
|
|
|
udelay(2); /* Need to wait before accessing SYSCONFIG back */
|
|
|
|
/* Wait for soft RESET to complete */
|
|
while ((readl(&uhh->sysc) & 0x1)) {
|
|
if (timeout > 100) {
|
|
printf("%s: RESET timeout\n", __func__);
|
|
return -1;
|
|
}
|
|
udelay(10);
|
|
timeout++;
|
|
}
|
|
|
|
writel(OMAP_UHH_SYSCONFIG_VAL, &uhh->sysc);
|
|
break;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int omap_ehci_tll_reset(void)
|
|
{
|
|
unsigned long init = get_timer(0);
|
|
|
|
/* perform TLL soft reset, and wait until reset is complete */
|
|
writel(OMAP_USBTLL_SYSCONFIG_SOFTRESET, &usbtll->sysc);
|
|
|
|
/* Wait for TLL reset to complete */
|
|
while (!(readl(&usbtll->syss) & OMAP_USBTLL_SYSSTATUS_RESETDONE))
|
|
if (get_timer(init) > CONFIG_SYS_HZ) {
|
|
debug("OMAP EHCI error: timeout resetting TLL\n");
|
|
return -EL3RST;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void omap_usbhs_hsic_init(int port)
|
|
{
|
|
unsigned int reg;
|
|
|
|
/* Enable channels now */
|
|
reg = readl(&usbtll->channel_conf + port);
|
|
|
|
setbits_le32(®, (OMAP_TLL_CHANNEL_CONF_CHANMODE_TRANSPARENT_UTMI
|
|
| OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF
|
|
| OMAP_TLL_CHANNEL_CONF_DRVVBUS
|
|
| OMAP_TLL_CHANNEL_CONF_CHRGVBUS
|
|
| OMAP_TLL_CHANNEL_CONF_CHANEN));
|
|
|
|
writel(reg, &usbtll->channel_conf + port);
|
|
}
|
|
|
|
#ifdef CONFIG_USB_ULPI
|
|
static void omap_ehci_soft_phy_reset(int port)
|
|
{
|
|
struct ulpi_viewport ulpi_vp;
|
|
|
|
ulpi_vp.viewport_addr = (u32)&ehci->insreg05_utmi_ulpi;
|
|
ulpi_vp.port_num = port;
|
|
|
|
ulpi_reset(&ulpi_vp);
|
|
}
|
|
#else
|
|
static void omap_ehci_soft_phy_reset(int port)
|
|
{
|
|
return;
|
|
}
|
|
#endif
|
|
|
|
#if defined(CONFIG_OMAP_EHCI_PHY1_RESET_GPIO) || \
|
|
defined(CONFIG_OMAP_EHCI_PHY2_RESET_GPIO) || \
|
|
defined(CONFIG_OMAP_EHCI_PHY3_RESET_GPIO)
|
|
/* controls PHY(s) reset signal(s) */
|
|
static inline void omap_ehci_phy_reset(int on, int delay)
|
|
{
|
|
/*
|
|
* Refer ISSUE1:
|
|
* Hold the PHY in RESET for enough time till
|
|
* PHY is settled and ready
|
|
*/
|
|
if (delay && !on)
|
|
udelay(delay);
|
|
#ifdef CONFIG_OMAP_EHCI_PHY1_RESET_GPIO
|
|
gpio_request(CONFIG_OMAP_EHCI_PHY1_RESET_GPIO, "USB PHY1 reset");
|
|
gpio_direction_output(CONFIG_OMAP_EHCI_PHY1_RESET_GPIO, !on);
|
|
#endif
|
|
#ifdef CONFIG_OMAP_EHCI_PHY2_RESET_GPIO
|
|
gpio_request(CONFIG_OMAP_EHCI_PHY2_RESET_GPIO, "USB PHY2 reset");
|
|
gpio_direction_output(CONFIG_OMAP_EHCI_PHY2_RESET_GPIO, !on);
|
|
#endif
|
|
#ifdef CONFIG_OMAP_EHCI_PHY3_RESET_GPIO
|
|
gpio_request(CONFIG_OMAP_EHCI_PHY3_RESET_GPIO, "USB PHY3 reset");
|
|
gpio_direction_output(CONFIG_OMAP_EHCI_PHY3_RESET_GPIO, !on);
|
|
#endif
|
|
|
|
/* Hold the PHY in RESET for enough time till DIR is high */
|
|
/* Refer: ISSUE1 */
|
|
if (delay && on)
|
|
udelay(delay);
|
|
}
|
|
#else
|
|
#define omap_ehci_phy_reset(on, delay) do {} while (0)
|
|
#endif
|
|
|
|
/* Reset is needed otherwise the kernel-driver will throw an error. */
|
|
int omap_ehci_hcd_stop(void)
|
|
{
|
|
debug("Resetting OMAP EHCI\n");
|
|
omap_ehci_phy_reset(1, 0);
|
|
|
|
if (omap_uhh_reset() < 0)
|
|
return -1;
|
|
|
|
if (omap_ehci_tll_reset() < 0)
|
|
return -1;
|
|
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* Initialize the OMAP EHCI controller and PHY.
|
|
* Based on "drivers/usb/host/ehci-omap.c" from Linux 3.1
|
|
* See there for additional Copyrights.
|
|
*/
|
|
int omap_ehci_hcd_init(int index, struct omap_usbhs_board_data *usbhs_pdata,
|
|
struct ehci_hccr **hccr, struct ehci_hcor **hcor)
|
|
{
|
|
int ret;
|
|
unsigned int i, reg = 0, rev = 0;
|
|
|
|
debug("Initializing OMAP EHCI\n");
|
|
|
|
ret = board_usb_init(index, USB_INIT_HOST);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
/* Put the PHY in RESET */
|
|
omap_ehci_phy_reset(1, 10);
|
|
|
|
ret = omap_uhh_reset();
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
ret = omap_ehci_tll_reset();
|
|
if (ret)
|
|
return ret;
|
|
|
|
writel(OMAP_USBTLL_SYSCONFIG_ENAWAKEUP |
|
|
OMAP_USBTLL_SYSCONFIG_SIDLEMODE |
|
|
OMAP_USBTLL_SYSCONFIG_CACTIVITY, &usbtll->sysc);
|
|
|
|
/* Put UHH in NoIdle/NoStandby mode */
|
|
writel(OMAP_UHH_SYSCONFIG_VAL, &uhh->sysc);
|
|
|
|
/* setup ULPI bypass and burst configurations */
|
|
clrsetbits_le32(®, OMAP_UHH_HOSTCONFIG_INCRX_ALIGN_EN,
|
|
(OMAP_UHH_HOSTCONFIG_INCR4_BURST_EN |
|
|
OMAP_UHH_HOSTCONFIG_INCR8_BURST_EN |
|
|
OMAP_UHH_HOSTCONFIG_INCR16_BURST_EN));
|
|
|
|
rev = readl(&uhh->rev);
|
|
if (rev == OMAP_USBHS_REV1) {
|
|
if (is_ehci_phy_mode(usbhs_pdata->port_mode[0]))
|
|
clrbits_le32(®, OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS);
|
|
else
|
|
setbits_le32(®, OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS);
|
|
|
|
if (is_ehci_phy_mode(usbhs_pdata->port_mode[1]))
|
|
clrbits_le32(®, OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS);
|
|
else
|
|
setbits_le32(®, OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS);
|
|
|
|
if (is_ehci_phy_mode(usbhs_pdata->port_mode[2]))
|
|
clrbits_le32(®, OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS);
|
|
else
|
|
setbits_le32(®, OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS);
|
|
} else if (rev == OMAP_USBHS_REV2) {
|
|
|
|
clrsetbits_le32(®, (OMAP_P1_MODE_CLEAR | OMAP_P2_MODE_CLEAR),
|
|
OMAP4_UHH_HOSTCONFIG_APP_START_CLK);
|
|
|
|
/* Clear port mode fields for PHY mode */
|
|
|
|
if (is_ehci_hsic_mode(usbhs_pdata->port_mode[0]))
|
|
setbits_le32(®, OMAP_P1_MODE_HSIC);
|
|
|
|
if (is_ehci_hsic_mode(usbhs_pdata->port_mode[1]))
|
|
setbits_le32(®, OMAP_P2_MODE_HSIC);
|
|
|
|
} else if (rev == OMAP_USBHS_REV2_1) {
|
|
|
|
clrsetbits_le32(®,
|
|
(OMAP_P1_MODE_CLEAR |
|
|
OMAP_P2_MODE_CLEAR |
|
|
OMAP_P3_MODE_CLEAR),
|
|
OMAP4_UHH_HOSTCONFIG_APP_START_CLK);
|
|
|
|
/* Clear port mode fields for PHY mode */
|
|
|
|
if (is_ehci_hsic_mode(usbhs_pdata->port_mode[0]))
|
|
setbits_le32(®, OMAP_P1_MODE_HSIC);
|
|
|
|
if (is_ehci_hsic_mode(usbhs_pdata->port_mode[1]))
|
|
setbits_le32(®, OMAP_P2_MODE_HSIC);
|
|
|
|
if (is_ehci_hsic_mode(usbhs_pdata->port_mode[2]))
|
|
setbits_le32(®, OMAP_P3_MODE_HSIC);
|
|
}
|
|
|
|
debug("OMAP UHH_REVISION 0x%x\n", rev);
|
|
writel(reg, &uhh->hostconfig);
|
|
|
|
for (i = 0; i < OMAP_HS_USB_PORTS; i++)
|
|
if (is_ehci_hsic_mode(usbhs_pdata->port_mode[i]))
|
|
omap_usbhs_hsic_init(i);
|
|
|
|
omap_ehci_phy_reset(0, 10);
|
|
|
|
/*
|
|
* An undocumented "feature" in the OMAP3 EHCI controller,
|
|
* causes suspended ports to be taken out of suspend when
|
|
* the USBCMD.Run/Stop bit is cleared (for example when
|
|
* we do ehci_bus_suspend).
|
|
* This breaks suspend-resume if the root-hub is allowed
|
|
* to suspend. Writing 1 to this undocumented register bit
|
|
* disables this feature and restores normal behavior.
|
|
*/
|
|
writel(EHCI_INSNREG04_DISABLE_UNSUSPEND, &ehci->insreg04);
|
|
|
|
for (i = 0; i < OMAP_HS_USB_PORTS; i++)
|
|
if (is_ehci_phy_mode(usbhs_pdata->port_mode[i]))
|
|
omap_ehci_soft_phy_reset(i);
|
|
|
|
*hccr = (struct ehci_hccr *)(OMAP_EHCI_BASE);
|
|
*hcor = (struct ehci_hcor *)(OMAP_EHCI_BASE + 0x10);
|
|
|
|
debug("OMAP EHCI init done\n");
|
|
return 0;
|
|
}
|