mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-08 22:24:32 +00:00
35f9d9bdd0
In legacy CONFIG_HARD_SPI initalizing spi_init code, which was removed during dm conversion cleanup. So remove the dead instances of CONFIG_HARD_SPI, and related code. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
322 lines
9.1 KiB
C
322 lines
9.1 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* Configuation settings for the Freescale MCF54418 TWR board.
|
|
*
|
|
* Copyright 2010-2012 Freescale Semiconductor, Inc.
|
|
* TsiChung Liew (Tsi-Chung.Liew@freescale.com)
|
|
*/
|
|
|
|
/*
|
|
* board/config.h - configuration options, board specific
|
|
*/
|
|
|
|
#ifndef _M54418TWR_H
|
|
#define _M54418TWR_H
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
* (easy to change)
|
|
*/
|
|
|
|
#define CONFIG_MCFUART
|
|
#define CONFIG_SYS_UART_PORT (0)
|
|
#define CONFIG_SYS_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
|
|
|
|
#define LDS_BOARD_TEXT board/freescale/m54418twr/sbf_dram_init.o (.text*)
|
|
|
|
#undef CONFIG_WATCHDOG
|
|
|
|
#define CONFIG_TIMESTAMP /* Print image info with timestamp */
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
|
|
/*
|
|
* NAND FLASH
|
|
*/
|
|
#ifdef CONFIG_CMD_NAND
|
|
#define CONFIG_JFFS2_NAND
|
|
#define CONFIG_NAND_FSL_NFC
|
|
#define CONFIG_SYS_NAND_BASE 0xFC0FC000
|
|
#define CONFIG_SYS_MAX_NAND_DEVICE 1
|
|
#define NAND_MAX_CHIPS CONFIG_SYS_MAX_NAND_DEVICE
|
|
#define CONFIG_SYS_NAND_SELECT_DEVICE
|
|
#endif
|
|
|
|
/* Network configuration */
|
|
#define CONFIG_MCFFEC
|
|
#ifdef CONFIG_MCFFEC
|
|
#define CONFIG_MII_INIT 1
|
|
#define CONFIG_SYS_DISCOVER_PHY
|
|
#define CONFIG_SYS_RX_ETH_BUFFER 2
|
|
#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
|
|
#define CONFIG_SYS_TX_ETH_BUFFER 2
|
|
#define CONFIG_HAS_ETH1
|
|
|
|
#define CONFIG_SYS_FEC0_PINMUX 0
|
|
#define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE
|
|
#define CONFIG_SYS_FEC1_PINMUX 0
|
|
#define CONFIG_SYS_FEC1_MIIBASE CONFIG_SYS_FEC0_MIIBASE
|
|
#define MCFFEC_TOUT_LOOP 50000
|
|
#define CONFIG_SYS_FEC0_PHYADDR 0
|
|
#define CONFIG_SYS_FEC1_PHYADDR 1
|
|
|
|
#define CONFIG_ETHPRIME "FEC0"
|
|
#define CONFIG_IPADDR 192.168.1.2
|
|
#define CONFIG_NETMASK 255.255.255.0
|
|
#define CONFIG_SERVERIP 192.168.1.1
|
|
#define CONFIG_GATEWAYIP 192.168.1.1
|
|
|
|
#define CONFIG_SYS_FEC_BUF_USE_SRAM
|
|
/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
|
|
#ifndef CONFIG_SYS_DISCOVER_PHY
|
|
#define FECDUPLEX FULL
|
|
#define FECSPEED _100BASET
|
|
#define LINKSTATUS 1
|
|
#else
|
|
#define LINKSTATUS 0
|
|
#ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
|
|
#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
|
|
#endif
|
|
#endif /* CONFIG_SYS_DISCOVER_PHY */
|
|
#endif
|
|
|
|
#define CONFIG_HOSTNAME "M54418TWR"
|
|
|
|
#if defined(CONFIG_CF_SBF)
|
|
/* ST Micro serial flash */
|
|
#define CONFIG_SYS_LOAD_ADDR2 0x40010007
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"netdev=eth0\0" \
|
|
"inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \
|
|
"loadaddr=0x40010000\0" \
|
|
"sbfhdr=sbfhdr.bin\0" \
|
|
"uboot=u-boot.bin\0" \
|
|
"load=tftp ${loadaddr} ${sbfhdr};" \
|
|
"tftp " __stringify(CONFIG_SYS_LOAD_ADDR2) " ${uboot} \0" \
|
|
"upd=run load; run prog\0" \
|
|
"prog=sf probe 0:1 1000000 3;" \
|
|
"sf erase 0 40000;" \
|
|
"sf write ${loadaddr} 0 40000;" \
|
|
"save\0" \
|
|
""
|
|
#elif defined(CONFIG_SYS_NAND_BOOT)
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"netdev=eth0\0" \
|
|
"inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \
|
|
"loadaddr=0x40010000\0" \
|
|
"u-boot=u-boot.bin\0" \
|
|
"load=tftp ${loadaddr} ${u-boot};\0" \
|
|
"upd=run load; run prog\0" \
|
|
"prog=nand device 0;" \
|
|
"nand erase 0 40000;" \
|
|
"nb_update ${loadaddr} ${filesize};" \
|
|
"save\0" \
|
|
""
|
|
#else
|
|
#define CONFIG_SYS_UBOOT_END 0x3FFFF
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"netdev=eth0\0" \
|
|
"inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \
|
|
"loadaddr=40010000\0" \
|
|
"u-boot=u-boot.bin\0" \
|
|
"load=tftp ${loadaddr) ${u-boot}\0" \
|
|
"upd=run load; run prog\0" \
|
|
"prog=prot off mram" " ;" \
|
|
"cp.b ${loadaddr} 0 ${filesize};" \
|
|
"save\0" \
|
|
""
|
|
#endif
|
|
|
|
/* Realtime clock */
|
|
#undef CONFIG_MCFRTC
|
|
#define CONFIG_RTC_MCFRRTC
|
|
#define CONFIG_SYS_MCFRRTC_BASE 0xFC0A8000
|
|
|
|
/* Timer */
|
|
#define CONFIG_MCFTMR
|
|
#undef CONFIG_MCFPIT
|
|
|
|
/* I2c */
|
|
#undef CONFIG_SYS_FSL_I2C
|
|
#undef CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
|
|
/* I2C speed and slave address */
|
|
#define CONFIG_SYS_I2C_SPEED 80000
|
|
#define CONFIG_SYS_I2C_SLAVE 0x7F
|
|
#define CONFIG_SYS_I2C_OFFSET 0x58000
|
|
#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
|
|
|
|
/* DSPI and Serial Flash */
|
|
#define CONFIG_CF_DSPI
|
|
#define CONFIG_SERIAL_FLASH
|
|
#define CONFIG_SYS_SBFHDR_SIZE 0x7
|
|
#ifdef CONFIG_CMD_SPI
|
|
|
|
# define CONFIG_SYS_DSPI_CTAR0 (DSPI_CTAR_TRSZ(7) | \
|
|
DSPI_CTAR_PCSSCK_1CLK | \
|
|
DSPI_CTAR_PASC(0) | \
|
|
DSPI_CTAR_PDT(0) | \
|
|
DSPI_CTAR_CSSCK(0) | \
|
|
DSPI_CTAR_ASC(0) | \
|
|
DSPI_CTAR_DT(1))
|
|
# define CONFIG_SYS_DSPI_CTAR1 (CONFIG_SYS_DSPI_CTAR0)
|
|
# define CONFIG_SYS_DSPI_CTAR2 (CONFIG_SYS_DSPI_CTAR0)
|
|
#endif
|
|
|
|
/* Input, PCI, Flexbus, and VCO */
|
|
#define CONFIG_EXTRA_CLOCK
|
|
|
|
#define CONFIG_PRAM 2048 /* 2048 KB */
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x10000)
|
|
|
|
#define CONFIG_SYS_MBAR 0xFC000000
|
|
|
|
/*
|
|
* Low Level Configuration Settings
|
|
* (address mappings, register initial values, etc.)
|
|
* You should know what you are doing if you make changes here.
|
|
*/
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Definitions for initial stack pointer and data area (in DPRAM)
|
|
*/
|
|
#define CONFIG_SYS_INIT_RAM_ADDR 0x80000000
|
|
/* End of used area in internal SRAM */
|
|
#define CONFIG_SYS_INIT_RAM_SIZE 0x10000
|
|
#define CONFIG_SYS_INIT_RAM_CTRL 0x221
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - \
|
|
GENERATED_GBL_DATA_SIZE) - 32)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
#define CONFIG_SYS_SBFHDR_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - 32)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Start addresses for the final memory configuration
|
|
* (Set up by the startup code)
|
|
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
|
|
*/
|
|
#define CONFIG_SYS_SDRAM_BASE 0x40000000
|
|
#define CONFIG_SYS_SDRAM_SIZE 128 /* SDRAM size in MB */
|
|
|
|
#define CONFIG_SYS_MEMTEST_START (CONFIG_SYS_SDRAM_BASE + 0x400)
|
|
#define CONFIG_SYS_MEMTEST_END ((CONFIG_SYS_SDRAM_SIZE - 3) << 20)
|
|
#define CONFIG_SYS_DRAM_TEST
|
|
|
|
#if defined(CONFIG_CF_SBF) || defined(CONFIG_SYS_NAND_BOOT)
|
|
#define CONFIG_SERIAL_BOOT
|
|
#endif
|
|
|
|
#if defined(CONFIG_SERIAL_BOOT)
|
|
#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_TEXT_BASE + 0x400)
|
|
#else
|
|
#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
|
|
#endif
|
|
|
|
#define CONFIG_SYS_BOOTPARAMS_LEN (64 * 1024)
|
|
/* Reserve 256 kB for Monitor */
|
|
#define CONFIG_SYS_MONITOR_LEN (256 << 10)
|
|
/* Reserve 256 kB for malloc() */
|
|
#define CONFIG_SYS_MALLOC_LEN (256 << 10)
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 8 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization ??
|
|
*/
|
|
/* Initial Memory map for Linux */
|
|
#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + \
|
|
(CONFIG_SYS_SDRAM_SIZE << 20))
|
|
|
|
/* Configuration for environment
|
|
* Environment is embedded in u-boot in the second sector of the flash
|
|
*/
|
|
#if !defined(CONFIG_SERIAL_BOOT) /*MRAM boot*/
|
|
#define CONFIG_ENV_ADDR (0x40000 - 0x1000) /*MRAM size 40000*/
|
|
#define CONFIG_ENV_SIZE 0x1000
|
|
#endif
|
|
|
|
#if defined(CONFIG_CF_SBF)
|
|
#define CONFIG_ENV_SPI_CS 1
|
|
#define CONFIG_ENV_OFFSET 0x40000
|
|
#define CONFIG_ENV_SIZE 0x2000
|
|
#define CONFIG_ENV_SECT_SIZE 0x10000
|
|
#endif
|
|
#if defined(CONFIG_SYS_NAND_BOOT)
|
|
#define CONFIG_ENV_OFFSET 0x80000
|
|
#define CONFIG_ENV_SIZE 0x20000
|
|
#define CONFIG_ENV_SECT_SIZE 0x20000
|
|
#endif
|
|
#undef CONFIG_ENV_OVERWRITE
|
|
|
|
/* FLASH organization */
|
|
#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE
|
|
|
|
#ifdef CONFIG_SYS_FLASH_CFI
|
|
|
|
/* Max size that the board might have */
|
|
#define CONFIG_SYS_FLASH_SIZE 0x1000000
|
|
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
|
|
/* max number of memory banks */
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1
|
|
/* max number of sectors on one chip */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 270
|
|
/* "Real" (hardware) sectors protection */
|
|
#define CONFIG_SYS_FLASH_CHECKSUM
|
|
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_CS0_BASE }
|
|
#else
|
|
/* max number of sectors on one chip */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 270
|
|
/* max number of sectors on one chip */
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 0
|
|
#endif
|
|
|
|
/*
|
|
* This is setting for JFFS2 support in u-boot.
|
|
* NOTE: Enable CONFIG_CMD_JFFS2 for JFFS2 support.
|
|
*/
|
|
#ifdef CONFIG_CMD_JFFS2
|
|
#define CONFIG_JFFS2_DEV "nand0"
|
|
#define CONFIG_JFFS2_PART_OFFSET (0x800000)
|
|
|
|
#endif
|
|
|
|
/* Cache Configuration */
|
|
#define CONFIG_SYS_CACHELINE_SIZE 16
|
|
#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
|
|
CONFIG_SYS_INIT_RAM_SIZE - 8)
|
|
#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
|
|
CONFIG_SYS_INIT_RAM_SIZE - 4)
|
|
#define CONFIG_SYS_ICACHE_INV (CF_CACR_BCINVA + CF_CACR_ICINVA)
|
|
#define CONFIG_SYS_DCACHE_INV (CF_CACR_DCINVA)
|
|
#define CONFIG_SYS_CACHE_ACR2 (CONFIG_SYS_SDRAM_BASE | \
|
|
CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
|
|
CF_ACR_EN | CF_ACR_SM_ALL)
|
|
#define CONFIG_SYS_CACHE_ICACR (CF_CACR_BEC | CF_CACR_IEC | \
|
|
CF_CACR_ICINVA | CF_CACR_EUSP)
|
|
#define CONFIG_SYS_CACHE_DCACR ((CONFIG_SYS_CACHE_ICACR | \
|
|
CF_CACR_DEC | CF_CACR_DDCM_P | \
|
|
CF_CACR_DCINVA) & ~CF_CACR_ICINVA)
|
|
|
|
#define CACR_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
|
|
CONFIG_SYS_INIT_RAM_SIZE - 12)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Memory bank definitions
|
|
*/
|
|
/*
|
|
* CS0 - NOR Flash 16MB
|
|
* CS1 - Available
|
|
* CS2 - Available
|
|
* CS3 - Available
|
|
* CS4 - Available
|
|
* CS5 - Available
|
|
*/
|
|
|
|
/* Flash */
|
|
#define CONFIG_SYS_CS0_BASE 0x00000000
|
|
#define CONFIG_SYS_CS0_MASK 0x000F0101
|
|
#define CONFIG_SYS_CS0_CTRL 0x00001D60
|
|
|
|
#endif /* _M54418TWR_H */
|