mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-17 10:18:38 +00:00
27c78e06f2
The PEXHC PCIe configuration mechanism ensures that the FPGA get configured at power-up. Since all the PCIe devices should be configured when the kernel start, u-boot has to take care that the FPGA gets configured also in other reset scenarios, mostly because of possible configuration change. The used mechanism is taken from the km_kirkwood design and adapted to the kmp204x case (slightly different HW and PCIe configuration). Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
120 lines
2.5 KiB
C
120 lines
2.5 KiB
C
/*
|
|
* (C) Copyright 2013 Keymile AG
|
|
* Valentin Longchamp <valentin.longchamp@keymile.com>
|
|
*
|
|
* Copyright 2007-2011 Freescale Semiconductor, Inc.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <command.h>
|
|
#include <pci.h>
|
|
#include <asm/fsl_pci.h>
|
|
#include <libfdt.h>
|
|
#include <fdt_support.h>
|
|
#include <asm/fsl_serdes.h>
|
|
#include <asm/errno.h>
|
|
|
|
#include "kmp204x.h"
|
|
|
|
#define PROM_SEL_L 11
|
|
/* control the PROM_SEL_L signal*/
|
|
static void toggle_fpga_eeprom_bus(bool cpu_own)
|
|
{
|
|
qrio_gpio_direction_output(GPIO_A, PROM_SEL_L, !cpu_own);
|
|
}
|
|
|
|
#define CONF_SEL_L 10
|
|
#define FPGA_PROG_L 19
|
|
#define FPGA_DONE 18
|
|
#define FPGA_INIT_L 17
|
|
|
|
int trigger_fpga_config(void)
|
|
{
|
|
int ret = 0, init_l;
|
|
/* approx 10ms */
|
|
u32 timeout = 10000;
|
|
|
|
/* make sure the FPGA_can access the EEPROM */
|
|
toggle_fpga_eeprom_bus(false);
|
|
|
|
/* assert CONF_SEL_L to be able to drive FPGA_PROG_L */
|
|
qrio_gpio_direction_output(GPIO_A, CONF_SEL_L, 0);
|
|
|
|
/* trigger the config start */
|
|
qrio_gpio_direction_output(GPIO_A, FPGA_PROG_L, 0);
|
|
|
|
/* small delay for INIT_L line */
|
|
udelay(10);
|
|
|
|
/* wait for FPGA_INIT to be asserted */
|
|
do {
|
|
init_l = qrio_get_gpio(GPIO_A, FPGA_INIT_L);
|
|
if (timeout-- == 0) {
|
|
printf("FPGA_INIT timeout\n");
|
|
ret = -EFAULT;
|
|
break;
|
|
}
|
|
udelay(10);
|
|
} while (init_l);
|
|
|
|
/* deassert FPGA_PROG, config should start */
|
|
qrio_set_gpio(GPIO_A, FPGA_PROG_L, 1);
|
|
|
|
return ret;
|
|
}
|
|
|
|
/* poll the FPGA_DONE signal and give the EEPROM back to the QorIQ */
|
|
static int wait_for_fpga_config(void)
|
|
{
|
|
int ret = 0, done;
|
|
/* approx 5 s */
|
|
u32 timeout = 500000;
|
|
|
|
printf("PCIe FPGA config:");
|
|
do {
|
|
done = qrio_get_gpio(GPIO_A, FPGA_DONE);
|
|
if (timeout-- == 0) {
|
|
printf(" FPGA_DONE timeout\n");
|
|
ret = -EFAULT;
|
|
goto err_out;
|
|
}
|
|
udelay(10);
|
|
} while (!done);
|
|
|
|
printf(" done\n");
|
|
|
|
err_out:
|
|
/* deactive CONF_SEL and give the CPU conf EEPROM access */
|
|
qrio_set_gpio(GPIO_A, CONF_SEL_L, 1);
|
|
toggle_fpga_eeprom_bus(true);
|
|
|
|
return ret;
|
|
}
|
|
|
|
#define PCIE_SW_RST 14
|
|
#define PEXHC_SW_RST 13
|
|
#define HOOPER_SW_RST 12
|
|
|
|
void pci_init_board(void)
|
|
{
|
|
/* first wait for the PCIe FPGA to be configured
|
|
* it has been triggered earlier in board_early_init_r */
|
|
int ret = wait_for_fpga_config();
|
|
if (ret)
|
|
printf("error finishing PCIe FPGA config\n");
|
|
|
|
qrio_prst(PCIE_SW_RST, false, false);
|
|
qrio_prst(PEXHC_SW_RST, false, false);
|
|
qrio_prst(HOOPER_SW_RST, false, false);
|
|
/* Hooper is not direcly PCIe capable */
|
|
mdelay(50);
|
|
|
|
fsl_pcie_init_board(0);
|
|
}
|
|
|
|
void pci_of_setup(void *blob, bd_t *bd)
|
|
{
|
|
FT_FSL_PCI_SETUP;
|
|
}
|