u-boot/drivers/mtd/spi
Siarhei Siamashka 19e99fb4ff sunxi: Support booting from SPI flash
Allwinner devices support SPI flash as one of the possible
bootable media type. The SPI flash chip needs to be connected
to SPI0 pins (port C) to make this work. More information is
available at:

    https://linux-sunxi.org/Bootable_SPI_flash

This patch adds the initial support for booting from SPI flash.
The existing SPI frameworks are not used in order to reduce the
SPL code size. Right now the SPL size grows by ~370 bytes when
CONFIG_SPL_SPI_SUNXI option is enabled.

While there are no popular Allwinner devices with SPI flash at
the moment, testing can be done using a SPI flash module (it
can be bought for ~2$ on ebay) and jumper wires with the boards,
which expose relevant pins on the expansion header. The SPI flash
chips themselves are very cheap (some prices are even listed as
low as 4 cents) and should not cost much if somebody decides to
design a development board with an SPI flash chip soldered on
the PCB.

Another nice feature of the SPI flash is that it can be safely
accessed in a device-independent way (since we know that the
boot ROM is already probing these pins during the boot time).
And if, for example, Olimex boards opted to use SPI flash instead
of EEPROM, then they would have been able to have U-Boot installed
in the SPI flash now and boot the rest of the system from the SATA
hard drive. Hopefully we may see new interesting Allwinner based
development boards in the future, now that the software support
for the SPI flash is in a better shape :-)

Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option
in a board defconfig, then building U-Boot and finally flashing
the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with
a help of the sunxi-fel tool:

   sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin

The device needs to be switched into FEL (USB recovery) mode first.
The most suitable boards for testing are Orange Pi PC and Pine64.
Because these boards are cheap, have no built-in NAND/eMMC and
expose SPI0 pins on the Raspberry Pi compatible expansion header.
The A13-OLinuXino-Micro board also can be used.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-15 08:34:34 +02:00
..
fsl_espi_spl.c driver: Add support of image load for MMC & SPI in SPL 2014-04-22 17:58:50 -07:00
Kconfig sunxi: Support booting from SPI flash 2016-07-15 08:34:34 +02:00
Makefile sunxi: Support booting from SPI flash 2016-07-15 08:34:34 +02:00
sandbox.c sandbox: spi: Remove an incorrect free() 2016-02-26 08:53:10 -07:00
sf-uclass.c dm: spi_flash: Allow the uclass to work without printf() 2016-01-15 05:39:27 -07:00
sf.c sf: Add CONFIG_SF_DUAL_FLASH 2014-01-12 21:40:22 +05:30
sf_dataflash.c dm: Rename dev_get_parentdata() to dev_get_parent_priv() 2015-10-23 09:42:28 -06:00
sf_internal.h spi: fsl_qspi: Enable Spansion S25FS-S family flashes 2016-05-18 08:51:16 -07:00
sf_mtd.c mtd, spi: Add MTD layer driver 2015-06-30 00:40:11 +05:30
sf_params.c driver: mtd: spi: Adding support for QSPI flash 2016-06-03 14:12:49 -07:00
sf_probe.c spi: Correct two error return values 2016-02-26 08:53:10 -07:00
spi_flash.c driver: mtd: spi: Adding support for QSPI flash 2016-06-03 14:12:49 -07:00
spi_spl_load.c spl: Support loading a FIT from SPI 2016-05-27 15:41:40 -04:00
sunxi_spi_spl.c sunxi: Support booting from SPI flash 2016-07-15 08:34:34 +02:00