mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-10 23:24:38 +00:00
0f89c54be9
The individual i2c commands imd, imm, inm, imw, icrc32, iprobe, iloop, and isdram are no longer available so all references to them have been updated to the new form of "i2c <cmd>". Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
82 lines
2.4 KiB
Text
82 lines
2.4 KiB
Text
XES XPedite1000 Board
|
|
|
|
Last Update: December 29, 2003
|
|
=======================================================================
|
|
|
|
This file contains some handy info regarding U-Boot and the XES
|
|
XPedite1000 PPC440GX PrPMC board. See the README.ppc440 for additional
|
|
information.
|
|
|
|
|
|
SWITCH SETTINGS & JUMPERS
|
|
==========================
|
|
|
|
Jumpers selected for AMD29LV040B flash part as the boot flash.
|
|
|
|
|
|
I2C Strap EEPROM & Environment Settings
|
|
=======================================
|
|
|
|
The XPedite1000 uses a single I2C eeprom for the 440 strappings and for
|
|
the environment variables. The first page (256 bytes) contains the
|
|
strappings and the 2 EMAC HW Ethernet addresses. Be careful not to
|
|
change the 1st page of the EEPROM! Unpopulated jumper J560 can get you
|
|
out of trouble as it disables the strapping read from EEPROM.
|
|
|
|
I2C probe
|
|
=====================
|
|
|
|
The i2c utilities work and have been tested on Rev B. of the 440GX. See
|
|
README.ebony for more information about i2c probing with the 440.
|
|
|
|
|
|
GETTING OUT OF I2C TROUBLE
|
|
===========================
|
|
|
|
(Direct quote from README.ebony)
|
|
If you're like me ... you may have screwed up your bootstrap serial
|
|
eeprom ... or worse, your SPD eeprom when experimenting with the
|
|
i2c commands. If so, here are some ideas on how to get out of
|
|
trouble:
|
|
|
|
Serial bootstrap eeprom corruption:
|
|
-----------------------------------
|
|
Power down the board and set the following straps:
|
|
|
|
J560 - closed
|
|
|
|
This will select the default sys0 and sys1 settings (the serial
|
|
eeproms are not used). Then power up the board and fix the serial
|
|
eeprom using the 'i2c mm' command. Here are the values I currently
|
|
use:
|
|
|
|
=> i2c md 50 0 10
|
|
|
|
0000: 85 7d 42 06 07 80 11 00 00 00 00 00 00 00 00 00 .}B.............
|
|
|
|
Once you have the eeproms set correctly change the
|
|
J560 straps as you desire.
|
|
|
|
|
|
PPC440GX Ethernet EMACs
|
|
=======================
|
|
|
|
The XES XPedite1000 uses emac 2 & 3 and ignores emac 0 & 1. PHYs are connected
|
|
only to emac 2 & 3. The HW Ethernet addresses are read from the i2c eeprom and
|
|
placed in the bd info structure for enet2addr and enet3addr. The ethernet driver
|
|
senses that enetaddr and enet1addr are 0's and does not use them.
|
|
|
|
As of this writing gigabit ethernet and the TCPIP acceleration hardware is not
|
|
supported.
|
|
|
|
|
|
Flash Support
|
|
=============
|
|
|
|
As of this writing, there is support for the 1/2mb boot flash only. User flash
|
|
is not yet supported.
|
|
|
|
|
|
Regards,
|
|
--Travis
|
|
<travis.sawyer@sandburst.com>
|