mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-30 00:21:06 +00:00
1a4596601f
Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
472 lines
11 KiB
C
472 lines
11 KiB
C
/*
|
|
* Faraday 10/100Mbps Ethernet Controller
|
|
*
|
|
* (C) Copyright 2010 Faraday Technology
|
|
* Dante Su <dantesu@faraday-tech.com>
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <command.h>
|
|
#include <malloc.h>
|
|
#include <net.h>
|
|
#include <asm/errno.h>
|
|
#include <asm/io.h>
|
|
#include <asm/dma-mapping.h>
|
|
|
|
#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
|
|
#include <miiphy.h>
|
|
#endif
|
|
|
|
#include "ftmac110.h"
|
|
|
|
#define CFG_RXDES_NUM 8
|
|
#define CFG_TXDES_NUM 2
|
|
#define CFG_XBUF_SIZE 1536
|
|
|
|
#define CFG_MDIORD_TIMEOUT (CONFIG_SYS_HZ >> 1) /* 500 ms */
|
|
#define CFG_MDIOWR_TIMEOUT (CONFIG_SYS_HZ >> 1) /* 500 ms */
|
|
#define CFG_LINKUP_TIMEOUT (CONFIG_SYS_HZ << 2) /* 4 sec */
|
|
|
|
/*
|
|
* FTMAC110 DMA design issue
|
|
*
|
|
* Its DMA engine has a weird restriction that its Rx DMA engine
|
|
* accepts only 16-bits aligned address, 32-bits aligned is not
|
|
* acceptable. However this restriction does not apply to Tx DMA.
|
|
*
|
|
* Conclusion:
|
|
* (1) Tx DMA Buffer Address:
|
|
* 1 bytes aligned: Invalid
|
|
* 2 bytes aligned: O.K
|
|
* 4 bytes aligned: O.K (-> u-boot ZeroCopy is possible)
|
|
* (2) Rx DMA Buffer Address:
|
|
* 1 bytes aligned: Invalid
|
|
* 2 bytes aligned: O.K
|
|
* 4 bytes aligned: Invalid
|
|
*/
|
|
|
|
struct ftmac110_chip {
|
|
void __iomem *regs;
|
|
uint32_t imr;
|
|
uint32_t maccr;
|
|
uint32_t lnkup;
|
|
uint32_t phy_addr;
|
|
|
|
struct ftmac110_rxd *rxd;
|
|
ulong rxd_dma;
|
|
uint32_t rxd_idx;
|
|
|
|
struct ftmac110_txd *txd;
|
|
ulong txd_dma;
|
|
uint32_t txd_idx;
|
|
};
|
|
|
|
static int ftmac110_reset(struct eth_device *dev);
|
|
|
|
static uint16_t mdio_read(struct eth_device *dev,
|
|
uint8_t phyaddr, uint8_t phyreg)
|
|
{
|
|
struct ftmac110_chip *chip = dev->priv;
|
|
struct ftmac110_regs __iomem *regs = chip->regs;
|
|
uint32_t tmp, ts;
|
|
uint16_t ret = 0xffff;
|
|
|
|
tmp = PHYCR_READ
|
|
| (phyaddr << PHYCR_ADDR_SHIFT)
|
|
| (phyreg << PHYCR_REG_SHIFT);
|
|
|
|
writel(tmp, ®s->phycr);
|
|
|
|
for (ts = get_timer(0); get_timer(ts) < CFG_MDIORD_TIMEOUT; ) {
|
|
tmp = readl(®s->phycr);
|
|
if (tmp & PHYCR_READ)
|
|
continue;
|
|
break;
|
|
}
|
|
|
|
if (tmp & PHYCR_READ)
|
|
printf("ftmac110: mdio read timeout\n");
|
|
else
|
|
ret = (uint16_t)(tmp & 0xffff);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static void mdio_write(struct eth_device *dev,
|
|
uint8_t phyaddr, uint8_t phyreg, uint16_t phydata)
|
|
{
|
|
struct ftmac110_chip *chip = dev->priv;
|
|
struct ftmac110_regs __iomem *regs = chip->regs;
|
|
uint32_t tmp, ts;
|
|
|
|
tmp = PHYCR_WRITE
|
|
| (phyaddr << PHYCR_ADDR_SHIFT)
|
|
| (phyreg << PHYCR_REG_SHIFT);
|
|
|
|
writel(phydata, ®s->phydr);
|
|
writel(tmp, ®s->phycr);
|
|
|
|
for (ts = get_timer(0); get_timer(ts) < CFG_MDIOWR_TIMEOUT; ) {
|
|
if (readl(®s->phycr) & PHYCR_WRITE)
|
|
continue;
|
|
break;
|
|
}
|
|
|
|
if (readl(®s->phycr) & PHYCR_WRITE)
|
|
printf("ftmac110: mdio write timeout\n");
|
|
}
|
|
|
|
static uint32_t ftmac110_phyqry(struct eth_device *dev)
|
|
{
|
|
ulong ts;
|
|
uint32_t maccr;
|
|
uint16_t pa, tmp, bmsr, bmcr;
|
|
struct ftmac110_chip *chip = dev->priv;
|
|
|
|
/* Default = 100Mbps Full */
|
|
maccr = MACCR_100M | MACCR_FD;
|
|
|
|
/* 1. find the phy device */
|
|
for (pa = 0; pa < 32; ++pa) {
|
|
tmp = mdio_read(dev, pa, MII_PHYSID1);
|
|
if (tmp == 0xFFFF || tmp == 0x0000)
|
|
continue;
|
|
chip->phy_addr = pa;
|
|
break;
|
|
}
|
|
if (pa >= 32) {
|
|
puts("ftmac110: phy device not found!\n");
|
|
goto exit;
|
|
}
|
|
|
|
/* 2. wait until link-up & auto-negotiation complete */
|
|
chip->lnkup = 0;
|
|
bmcr = mdio_read(dev, chip->phy_addr, MII_BMCR);
|
|
ts = get_timer(0);
|
|
do {
|
|
bmsr = mdio_read(dev, chip->phy_addr, MII_BMSR);
|
|
chip->lnkup = (bmsr & BMSR_LSTATUS) ? 1 : 0;
|
|
if (!chip->lnkup)
|
|
continue;
|
|
if (!(bmcr & BMCR_ANENABLE) || (bmsr & BMSR_ANEGCOMPLETE))
|
|
break;
|
|
} while (get_timer(ts) < CFG_LINKUP_TIMEOUT);
|
|
if (!chip->lnkup) {
|
|
puts("ftmac110: link down\n");
|
|
goto exit;
|
|
}
|
|
if (!(bmcr & BMCR_ANENABLE))
|
|
puts("ftmac110: auto negotiation disabled\n");
|
|
else if (!(bmsr & BMSR_ANEGCOMPLETE))
|
|
puts("ftmac110: auto negotiation timeout\n");
|
|
|
|
/* 3. derive MACCR */
|
|
if ((bmcr & BMCR_ANENABLE) && (bmsr & BMSR_ANEGCOMPLETE)) {
|
|
tmp = mdio_read(dev, chip->phy_addr, MII_ADVERTISE);
|
|
tmp &= mdio_read(dev, chip->phy_addr, MII_LPA);
|
|
if (tmp & LPA_100FULL) /* 100Mbps full-duplex */
|
|
maccr = MACCR_100M | MACCR_FD;
|
|
else if (tmp & LPA_100HALF) /* 100Mbps half-duplex */
|
|
maccr = MACCR_100M;
|
|
else if (tmp & LPA_10FULL) /* 10Mbps full-duplex */
|
|
maccr = MACCR_FD;
|
|
else if (tmp & LPA_10HALF) /* 10Mbps half-duplex */
|
|
maccr = 0;
|
|
} else {
|
|
if (bmcr & BMCR_SPEED100)
|
|
maccr = MACCR_100M;
|
|
else
|
|
maccr = 0;
|
|
if (bmcr & BMCR_FULLDPLX)
|
|
maccr |= MACCR_FD;
|
|
}
|
|
|
|
exit:
|
|
printf("ftmac110: %d Mbps, %s\n",
|
|
(maccr & MACCR_100M) ? 100 : 10,
|
|
(maccr & MACCR_FD) ? "Full" : "half");
|
|
return maccr;
|
|
}
|
|
|
|
static int ftmac110_reset(struct eth_device *dev)
|
|
{
|
|
uint8_t *a;
|
|
uint32_t i, maccr;
|
|
struct ftmac110_chip *chip = dev->priv;
|
|
struct ftmac110_regs __iomem *regs = chip->regs;
|
|
|
|
/* 1. MAC reset */
|
|
writel(MACCR_RESET, ®s->maccr);
|
|
for (i = get_timer(0); get_timer(i) < 1000; ) {
|
|
if (readl(®s->maccr) & MACCR_RESET)
|
|
continue;
|
|
break;
|
|
}
|
|
if (readl(®s->maccr) & MACCR_RESET) {
|
|
printf("ftmac110: reset failed\n");
|
|
return -ENXIO;
|
|
}
|
|
|
|
/* 1-1. Init tx ring */
|
|
for (i = 0; i < CFG_TXDES_NUM; ++i) {
|
|
/* owned by SW */
|
|
chip->txd[i].ct[0] = 0;
|
|
}
|
|
chip->txd_idx = 0;
|
|
|
|
/* 1-2. Init rx ring */
|
|
for (i = 0; i < CFG_RXDES_NUM; ++i) {
|
|
/* owned by HW */
|
|
chip->rxd[i].ct[0] = cpu_to_le32(FTMAC110_RXCT0_OWNER);
|
|
}
|
|
chip->rxd_idx = 0;
|
|
|
|
/* 2. PHY status query */
|
|
maccr = ftmac110_phyqry(dev);
|
|
|
|
/* 3. Fix up the MACCR value */
|
|
chip->maccr = maccr | MACCR_CRCAPD | MACCR_RXALL | MACCR_RXRUNT
|
|
| MACCR_RXEN | MACCR_TXEN | MACCR_RXDMAEN | MACCR_TXDMAEN;
|
|
|
|
/* 4. MAC address setup */
|
|
a = dev->enetaddr;
|
|
writel(a[1] | (a[0] << 8), ®s->mac[0]);
|
|
writel(a[5] | (a[4] << 8) | (a[3] << 16)
|
|
| (a[2] << 24), ®s->mac[1]);
|
|
|
|
/* 5. MAC registers setup */
|
|
writel(chip->rxd_dma, ®s->rxba);
|
|
writel(chip->txd_dma, ®s->txba);
|
|
/* interrupt at each tx/rx */
|
|
writel(ITC_DEFAULT, ®s->itc);
|
|
/* no tx pool, rx poll = 1 normal cycle */
|
|
writel(APTC_DEFAULT, ®s->aptc);
|
|
/* rx threshold = [6/8 fifo, 2/8 fifo] */
|
|
writel(DBLAC_DEFAULT, ®s->dblac);
|
|
/* disable & clear all interrupt status */
|
|
chip->imr = 0;
|
|
writel(ISR_ALL, ®s->isr);
|
|
writel(chip->imr, ®s->imr);
|
|
/* enable mac */
|
|
writel(chip->maccr, ®s->maccr);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int ftmac110_probe(struct eth_device *dev, bd_t *bis)
|
|
{
|
|
debug("ftmac110: probe\n");
|
|
|
|
if (ftmac110_reset(dev))
|
|
return -1;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void ftmac110_halt(struct eth_device *dev)
|
|
{
|
|
struct ftmac110_chip *chip = dev->priv;
|
|
struct ftmac110_regs __iomem *regs = chip->regs;
|
|
|
|
writel(0, ®s->imr);
|
|
writel(0, ®s->maccr);
|
|
|
|
debug("ftmac110: halt\n");
|
|
}
|
|
|
|
static int ftmac110_send(struct eth_device *dev, void *pkt, int len)
|
|
{
|
|
struct ftmac110_chip *chip = dev->priv;
|
|
struct ftmac110_regs __iomem *regs = chip->regs;
|
|
struct ftmac110_txd *des;
|
|
|
|
if (!chip->lnkup)
|
|
return 0;
|
|
|
|
if (len <= 0 || len > CFG_XBUF_SIZE) {
|
|
printf("ftmac110: bad tx pkt len(%d)\n", len);
|
|
return 0;
|
|
}
|
|
|
|
len = max(60, len);
|
|
|
|
des = &chip->txd[chip->txd_idx];
|
|
if (le32_to_cpu(des->ct[0]) & FTMAC110_TXCT0_OWNER) {
|
|
/* kick-off Tx DMA */
|
|
writel(0xffffffff, ®s->txpd);
|
|
printf("ftmac110: out of txd\n");
|
|
return 0;
|
|
}
|
|
|
|
memcpy(des->vbuf, (void *)pkt, len);
|
|
dma_map_single(des->vbuf, len, DMA_TO_DEVICE);
|
|
|
|
/* update len, fts and lts */
|
|
des->ct[1] &= cpu_to_le32(FTMAC110_TXCT1_END);
|
|
des->ct[1] |= cpu_to_le32(FTMAC110_TXCT1_LEN(len)
|
|
| FTMAC110_TXCT1_FTS | FTMAC110_TXCT1_LTS);
|
|
|
|
/* set owner bit and clear others */
|
|
des->ct[0] = cpu_to_le32(FTMAC110_TXCT0_OWNER);
|
|
|
|
/* kick-off Tx DMA */
|
|
writel(0xffffffff, ®s->txpd);
|
|
|
|
chip->txd_idx = (chip->txd_idx + 1) % CFG_TXDES_NUM;
|
|
|
|
return len;
|
|
}
|
|
|
|
static int ftmac110_recv(struct eth_device *dev)
|
|
{
|
|
struct ftmac110_chip *chip = dev->priv;
|
|
struct ftmac110_rxd *des;
|
|
uint32_t ct0, len, rlen = 0;
|
|
uint8_t *buf;
|
|
|
|
if (!chip->lnkup)
|
|
return 0;
|
|
|
|
do {
|
|
des = &chip->rxd[chip->rxd_idx];
|
|
ct0 = le32_to_cpu(des->ct[0]);
|
|
if (ct0 & FTMAC110_RXCT0_OWNER)
|
|
break;
|
|
|
|
len = FTMAC110_RXCT0_LEN(ct0);
|
|
buf = des->vbuf;
|
|
|
|
if (ct0 & FTMAC110_RXCT0_ERRMASK) {
|
|
printf("ftmac110: rx error\n");
|
|
} else {
|
|
dma_map_single(buf, len, DMA_FROM_DEVICE);
|
|
NetReceive(buf, len);
|
|
rlen += len;
|
|
}
|
|
|
|
/* owned by hardware */
|
|
des->ct[0] = cpu_to_le32(FTMAC110_RXCT0_OWNER);
|
|
|
|
chip->rxd_idx = (chip->rxd_idx + 1) % CFG_RXDES_NUM;
|
|
} while (0);
|
|
|
|
return rlen;
|
|
}
|
|
|
|
#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
|
|
|
|
static int ftmac110_mdio_read(
|
|
const char *devname, uint8_t addr, uint8_t reg, uint16_t *value)
|
|
{
|
|
int ret = 0;
|
|
struct eth_device *dev;
|
|
|
|
dev = eth_get_dev_by_name(devname);
|
|
if (dev == NULL) {
|
|
printf("%s: no such device\n", devname);
|
|
ret = -1;
|
|
} else {
|
|
*value = mdio_read(dev, addr, reg);
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int ftmac110_mdio_write(
|
|
const char *devname, uint8_t addr, uint8_t reg, uint16_t value)
|
|
{
|
|
int ret = 0;
|
|
struct eth_device *dev;
|
|
|
|
dev = eth_get_dev_by_name(devname);
|
|
if (dev == NULL) {
|
|
printf("%s: no such device\n", devname);
|
|
ret = -1;
|
|
} else {
|
|
mdio_write(dev, addr, reg, value);
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
#endif /* #if defined(CONFIG_MII) || defined(CONFIG_CMD_MII) */
|
|
|
|
int ftmac110_initialize(bd_t *bis)
|
|
{
|
|
int i, card_nr = 0;
|
|
struct eth_device *dev;
|
|
struct ftmac110_chip *chip;
|
|
|
|
dev = malloc(sizeof(*dev) + sizeof(*chip));
|
|
if (dev == NULL) {
|
|
panic("ftmac110: out of memory 1\n");
|
|
return -1;
|
|
}
|
|
chip = (struct ftmac110_chip *)(dev + 1);
|
|
memset(dev, 0, sizeof(*dev) + sizeof(*chip));
|
|
|
|
sprintf(dev->name, "FTMAC110#%d", card_nr);
|
|
|
|
dev->iobase = CONFIG_FTMAC110_BASE;
|
|
chip->regs = (void __iomem *)dev->iobase;
|
|
dev->priv = chip;
|
|
dev->init = ftmac110_probe;
|
|
dev->halt = ftmac110_halt;
|
|
dev->send = ftmac110_send;
|
|
dev->recv = ftmac110_recv;
|
|
|
|
if (!eth_getenv_enetaddr_by_index("eth", card_nr, dev->enetaddr))
|
|
eth_random_enetaddr(dev->enetaddr);
|
|
|
|
/* allocate tx descriptors (it must be 16 bytes aligned) */
|
|
chip->txd = dma_alloc_coherent(
|
|
sizeof(struct ftmac110_txd) * CFG_TXDES_NUM, &chip->txd_dma);
|
|
if (!chip->txd)
|
|
panic("ftmac110: out of memory 3\n");
|
|
memset(chip->txd, 0,
|
|
sizeof(struct ftmac110_txd) * CFG_TXDES_NUM);
|
|
for (i = 0; i < CFG_TXDES_NUM; ++i) {
|
|
void *va = memalign(ARCH_DMA_MINALIGN, CFG_XBUF_SIZE);
|
|
if (!va)
|
|
panic("ftmac110: out of memory 4\n");
|
|
chip->txd[i].vbuf = va;
|
|
chip->txd[i].buf = cpu_to_le32(virt_to_phys(va));
|
|
chip->txd[i].ct[1] = 0;
|
|
chip->txd[i].ct[0] = 0; /* owned by SW */
|
|
}
|
|
chip->txd[i - 1].ct[1] |= cpu_to_le32(FTMAC110_TXCT1_END);
|
|
chip->txd_idx = 0;
|
|
|
|
/* allocate rx descriptors (it must be 16 bytes aligned) */
|
|
chip->rxd = dma_alloc_coherent(
|
|
sizeof(struct ftmac110_rxd) * CFG_RXDES_NUM, &chip->rxd_dma);
|
|
if (!chip->rxd)
|
|
panic("ftmac110: out of memory 4\n");
|
|
memset((void *)chip->rxd, 0,
|
|
sizeof(struct ftmac110_rxd) * CFG_RXDES_NUM);
|
|
for (i = 0; i < CFG_RXDES_NUM; ++i) {
|
|
void *va = memalign(ARCH_DMA_MINALIGN, CFG_XBUF_SIZE + 2);
|
|
if (!va)
|
|
panic("ftmac110: out of memory 5\n");
|
|
/* it needs to be exactly 2 bytes aligned */
|
|
va = ((uint8_t *)va + 2);
|
|
chip->rxd[i].vbuf = va;
|
|
chip->rxd[i].buf = cpu_to_le32(virt_to_phys(va));
|
|
chip->rxd[i].ct[1] = cpu_to_le32(CFG_XBUF_SIZE);
|
|
chip->rxd[i].ct[0] = cpu_to_le32(FTMAC110_RXCT0_OWNER);
|
|
}
|
|
chip->rxd[i - 1].ct[1] |= cpu_to_le32(FTMAC110_RXCT1_END);
|
|
chip->rxd_idx = 0;
|
|
|
|
eth_register(dev);
|
|
|
|
#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
|
|
miiphy_register(dev->name, ftmac110_mdio_read, ftmac110_mdio_write);
|
|
#endif
|
|
|
|
card_nr++;
|
|
|
|
return card_nr;
|
|
}
|