u-boot/arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts
Marek Vasut 9b36b7dc96 ARM: dts: stm32: Add USB OTG ID pin on DH AV96
Add USB OTG ID pin mux and switch the USB OTG port
from peripheral to OTG mode.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2020-12-09 10:57:50 +01:00

212 lines
4.1 KiB
Text

// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
/*
* Copyright (C) Linaro Ltd 2019 - All Rights Reserved
* Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
* Copyright (C) 2020 Marek Vasut <marex@denx.de>
*/
/dts-v1/;
#include "stm32mp15xx-dhcor-io1v8.dtsi"
#include "stm32mp15xx-dhcor-avenger96-u-boot.dtsi"
/ {
model = "Arrow Electronics STM32MP15xx Avenger96 board";
compatible = "arrow,stm32mp15xx-avenger96", "st,stm32mp15x";
aliases {
eeprom0 = &eeprom0;
ethernet0 = &ethernet0;
mmc0 = &sdmmc1;
serial0 = &uart4;
serial1 = &uart7;
};
chosen {
stdout-path = "serial0:115200n8";
};
led {
compatible = "gpio-leds";
led1 {
label = "green:user0";
gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
default-state = "off";
};
led2 {
label = "green:user1";
gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "mmc0";
default-state = "off";
};
led3 {
label = "green:user2";
gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "mmc1";
default-state = "off";
};
led4 {
label = "green:user3";
gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "none";
default-state = "off";
panic-indicator;
};
led5 {
label = "yellow:wifi";
gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "phy0tx";
default-state = "off";
};
led6 {
label = "blue:bt";
gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "bluetooth-power";
default-state = "off";
};
};
sd_switch: regulator-sd_switch {
compatible = "regulator-gpio";
regulator-name = "sd_switch";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <2900000>;
regulator-type = "voltage";
regulator-always-on;
gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>;
gpios-states = <0>;
states = <1800000 0x1>,
<2900000 0x0>;
};
};
&ethernet0 {
status = "okay";
pinctrl-0 = <&ethernet0_rgmii_pins_c>;
pinctrl-1 = <&ethernet0_rgmii_sleep_pins_c>;
pinctrl-names = "default", "sleep";
phy-mode = "rgmii";
max-speed = <1000>;
phy-handle = <&phy0>;
phy-reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
mdio0 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "snps,dwmac-mdio";
phy0: ethernet-phy@7 {
reg = <7>;
};
};
};
&i2c1 { /* X6 I2C1 */
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins_b>;
i2c-scl-rising-time-ns = <185>;
i2c-scl-falling-time-ns = <20>;
status = "okay";
/delete-property/dmas;
/delete-property/dma-names;
};
&i2c2 { /* X6 I2C2 */
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins_c>;
i2c-scl-rising-time-ns = <185>;
i2c-scl-falling-time-ns = <20>;
status = "okay";
/delete-property/dmas;
/delete-property/dma-names;
};
&i2c4 {
eeprom0: eeprom@53 {
compatible = "atmel,24c02";
reg = <0x53>;
pagesize = <16>;
};
};
&sdmmc1 {
pinctrl-names = "default", "opendrain", "sleep";
pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>;
pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>;
pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>;
disable-wp;
st,sig-dir;
st,neg-edge;
st,use-ckin;
bus-width = <4>;
vmmc-supply = <&vdd_sd>;
vqmmc-supply = <&sd_switch>;
status = "okay";
};
&sdmmc2 {
pinctrl-names = "default";
pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>;
non-removable;
no-sd;
no-sdio;
st,neg-edge;
bus-width = <8>;
vmmc-supply = <&v3v3>;
mmc-ddr-3_3v;
status = "okay";
};
&spi2 {
pinctrl-names = "default";
pinctrl-0 = <&spi2_pins_a>;
status = "okay";
};
&uart4 {
/* On Low speed expansion header */
label = "LS-UART1";
pinctrl-names = "default";
pinctrl-0 = <&uart4_pins_b>;
status = "okay";
};
&uart7 {
/* On Low speed expansion header */
label = "LS-UART0";
pinctrl-names = "default";
pinctrl-0 = <&uart7_pins_a>;
status = "okay";
};
&usbh_ehci {
phys = <&usbphyc_port0>;
phy-names = "usb";
status = "okay";
};
&usbotg_hs {
pinctrl-0 = <&usbotg_hs_pins_a>;
pinctrl-names = "default";
phys = <&usbphyc_port1 0>;
phy-names = "usb2-phy";
status = "okay";
};
&usbphyc {
status = "okay";
};
&usbphyc_port0 {
phy-supply = <&vdd_usb>;
};
&usbphyc_port1 {
phy-supply = <&vdd_usb>;
};