u-boot/drivers/hwmon/adm1021.c
Wolfgang Denk 1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00

164 lines
3.7 KiB
C

/*
* (C) Copyright 2003
* Murray Jensen, CSIRO-MIT, Murray.Jensen@csiro.au
*
* based on dtt/lm75.c which is ...
*
* (C) Copyright 2001
* Bill Hunter, Wave 7 Optics, williamhunter@mediaone.net
*
* SPDX-License-Identifier: GPL-2.0+
*/
/*
* Analog Devices's ADM1021
* "Low Cost Microprocessor System Temperature Monitor"
*/
#include <common.h>
#include <i2c.h>
#include <dtt.h>
#define DTT_READ_LOC_VALUE 0x00
#define DTT_READ_REM_VALUE 0x01
#define DTT_READ_STATUS 0x02
#define DTT_READ_CONFIG 0x03
#define DTT_READ_CONVRATE 0x04
#define DTT_READ_LOC_HIGHLIM 0x05
#define DTT_READ_LOC_LOWLIM 0x06
#define DTT_READ_REM_HIGHLIM 0x07
#define DTT_READ_REM_LOWLIM 0x08
#define DTT_READ_DEVID 0xfe
#define DTT_WRITE_CONFIG 0x09
#define DTT_WRITE_CONVRATE 0x0a
#define DTT_WRITE_LOC_HIGHLIM 0x0b
#define DTT_WRITE_LOC_LOWLIM 0x0c
#define DTT_WRITE_REM_HIGHLIM 0x0d
#define DTT_WRITE_REM_LOWLIM 0x0e
#define DTT_WRITE_ONESHOT 0x0f
#define DTT_STATUS_BUSY 0x80 /* 1=ADC Converting */
#define DTT_STATUS_LHIGH 0x40 /* 1=Local High Temp Limit Tripped */
#define DTT_STATUS_LLOW 0x20 /* 1=Local Low Temp Limit Tripped */
#define DTT_STATUS_RHIGH 0x10 /* 1=Remote High Temp Limit Tripped */
#define DTT_STATUS_RLOW 0x08 /* 1=Remote Low Temp Limit Tripped */
#define DTT_STATUS_OPEN 0x04 /* 1=Remote Sensor Open-Circuit */
#define DTT_CONFIG_ALERT_MASKED 0x80 /* 0=ALERT Enabled, 1=ALERT Masked */
#define DTT_CONFIG_STANDBY 0x40 /* 0=Run, 1=Standby */
#define DTT_ADM1021_DEVID 0x41
typedef
struct {
uint i2c_addr:7; /* 7bit i2c chip address */
uint conv_rate:3; /* conversion rate */
uint enable_alert:1; /* enable alert output pin */
uint enable_local:1; /* enable internal temp sensor */
uint max_local:8; /* internal temp maximum */
uint min_local:8; /* internal temp minimum */
uint enable_remote:1; /* enable remote temp sensor */
uint max_remote:8; /* remote temp maximum */
uint min_remote:8; /* remote temp minimum */
}
dtt_cfg_t;
dtt_cfg_t dttcfg[] = CONFIG_SYS_DTT_ADM1021;
int
dtt_read (int sensor, int reg)
{
dtt_cfg_t *dcp = &dttcfg[sensor >> 1];
uchar data;
if (i2c_read(dcp->i2c_addr, reg, 1, &data, 1) != 0)
return -1;
return (int)data;
} /* dtt_read() */
int
dtt_write (int sensor, int reg, int val)
{
dtt_cfg_t *dcp = &dttcfg[sensor >> 1];
uchar data;
data = (uchar)(val & 0xff);
if (i2c_write(dcp->i2c_addr, reg, 1, &data, 1) != 0)
return 1;
return 0;
} /* dtt_write() */
int
dtt_init_one(int sensor)
{
dtt_cfg_t *dcp = &dttcfg[sensor >> 1];
int reg, val;
if (((sensor & 1) == 0 ? dcp->enable_local : dcp->enable_remote) == 0)
return 1; /* sensor is disabled (or rather ignored) */
/*
* Setup High Limit register
*/
if ((sensor & 1) == 0) {
reg = DTT_WRITE_LOC_HIGHLIM;
val = dcp->max_local;
}
else {
reg = DTT_WRITE_REM_HIGHLIM;
val = dcp->max_remote;
}
if (dtt_write (sensor, reg, val) != 0)
return 1;
/*
* Setup Low Limit register
*/
if ((sensor & 1) == 0) {
reg = DTT_WRITE_LOC_LOWLIM;
val = dcp->min_local;
}
else {
reg = DTT_WRITE_REM_LOWLIM;
val = dcp->min_remote;
}
if (dtt_write (sensor, reg, val) != 0)
return 1;
/* shouldn't hurt if the rest gets done twice */
/*
* Setup Conversion Rate register
*/
if (dtt_write (sensor, DTT_WRITE_CONVRATE, dcp->conv_rate) != 0)
return 1;
/*
* Setup configuraton register
*/
val = 0; /* running */
if (dcp->enable_alert == 0)
val |= DTT_CONFIG_ALERT_MASKED; /* mask ALERT pin */
if (dtt_write (sensor, DTT_WRITE_CONFIG, val) != 0)
return 1;
return 0;
} /* dtt_init_one() */
int
dtt_get_temp (int sensor)
{
signed char val;
if ((sensor & 1) == 0)
val = dtt_read(sensor, DTT_READ_LOC_VALUE);
else
val = dtt_read(sensor, DTT_READ_REM_VALUE);
return (int) val;
} /* dtt_get_temp() */