mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-29 22:43:10 +00:00
eaf6ea6a1d
- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR - Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack pointer directly, otherwise we use the common calculation. - On some platforms that were using the standard calculation but did not set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them. - On a small number of platforms that were not subtracting GENERATED_GBL_DATA_SIZE do so now via the standard calculation. - CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most board config header files. Signed-off-by: Tom Rini <trini@konsulko.com>
137 lines
3.9 KiB
C
137 lines
3.9 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* Copyright 2013 Freescale Semiconductor, Inc.
|
|
*
|
|
* Configuration settings for the Freescale Vybrid vf610twr board.
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
#include <asm/arch/imx-regs.h>
|
|
#include <linux/stringify.h>
|
|
|
|
/* NAND support */
|
|
|
|
#ifdef CONFIG_CMD_NAND
|
|
#define CONFIG_SYS_MAX_NAND_DEVICE 1
|
|
#define CONFIG_SYS_NAND_BASE NFC_BASE_ADDR
|
|
|
|
/* Dynamic MTD partition support */
|
|
#endif
|
|
|
|
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
|
|
#define CONFIG_SYS_FSL_ESDHC_NUM 1
|
|
|
|
#define CONFIG_FEC_MXC_PHYADDR 0
|
|
|
|
/* I2C Configs */
|
|
#define CONFIG_SYS_SPD_BUS_NUM 0
|
|
|
|
/*
|
|
* We do have 128MB of memory on the Vybrid Tower board. Leave the last
|
|
* 16MB alone to avoid conflicts with Cortex-M4 firmwares running from
|
|
* DDR3. Hence, limit the memory range for image processing to 112MB
|
|
* using bootm_size. All of the following must be within this range.
|
|
* We have the default load at 32MB into DDR (for the kernel), FDT at
|
|
* 64MB and the ramdisk 512KB above that (allowing for hopefully never
|
|
* seen large trees). This allows a reasonable split between ramdisk
|
|
* and kernel size, where the ram disk can be a bit larger.
|
|
*/
|
|
#define MEM_LAYOUT_ENV_SETTINGS \
|
|
"bootm_size=0x07000000\0" \
|
|
"loadaddr=0x82000000\0" \
|
|
"kernel_addr_r=0x82000000\0" \
|
|
"fdt_addr=0x84000000\0" \
|
|
"fdt_addr_r=0x84000000\0" \
|
|
"rdaddr=0x84080000\0" \
|
|
"ramdisk_addr_r=0x84080000\0"
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
MEM_LAYOUT_ENV_SETTINGS \
|
|
"script=boot.scr\0" \
|
|
"image=zImage\0" \
|
|
"console=ttyLP1\0" \
|
|
"fdt_file=vf610-twr.dtb\0" \
|
|
"boot_fdt=try\0" \
|
|
"ip_dyn=yes\0" \
|
|
"mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
|
|
"mmcpart=1\0" \
|
|
"mmcroot=/dev/mmcblk0p2 rootwait rw\0" \
|
|
"update_sd_firmware_filename=u-boot.imx\0" \
|
|
"update_sd_firmware=" \
|
|
"if test ${ip_dyn} = yes; then " \
|
|
"setenv get_cmd dhcp; " \
|
|
"else " \
|
|
"setenv get_cmd tftp; " \
|
|
"fi; " \
|
|
"if mmc dev ${mmcdev}; then " \
|
|
"if ${get_cmd} ${update_sd_firmware_filename}; then " \
|
|
"setexpr fw_sz ${filesize} / 0x200; " \
|
|
"setexpr fw_sz ${fw_sz} + 1; " \
|
|
"mmc write ${loadaddr} 0x2 ${fw_sz}; " \
|
|
"fi; " \
|
|
"fi\0" \
|
|
"mmcargs=setenv bootargs console=${console},${baudrate} " \
|
|
"root=${mmcroot}\0" \
|
|
"loadbootscript=" \
|
|
"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
|
|
"bootscript=echo Running bootscript from mmc ...; " \
|
|
"source\0" \
|
|
"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
|
|
"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
|
|
"mmcboot=echo Booting from mmc ...; " \
|
|
"run mmcargs; " \
|
|
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
|
|
"if run loadfdt; then " \
|
|
"bootz ${loadaddr} - ${fdt_addr}; " \
|
|
"else " \
|
|
"if test ${boot_fdt} = try; then " \
|
|
"bootz; " \
|
|
"else " \
|
|
"echo WARN: Cannot load the DT; " \
|
|
"fi; " \
|
|
"fi; " \
|
|
"else " \
|
|
"bootz; " \
|
|
"fi;\0" \
|
|
"netargs=setenv bootargs console=${console},${baudrate} " \
|
|
"root=/dev/nfs " \
|
|
"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
|
|
"netboot=echo Booting from net ...; " \
|
|
"run netargs; " \
|
|
"if test ${ip_dyn} = yes; then " \
|
|
"setenv get_cmd dhcp; " \
|
|
"else " \
|
|
"setenv get_cmd tftp; " \
|
|
"fi; " \
|
|
"${get_cmd} ${image}; " \
|
|
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
|
|
"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
|
|
"bootz ${loadaddr} - ${fdt_addr}; " \
|
|
"else " \
|
|
"if test ${boot_fdt} = try; then " \
|
|
"bootz; " \
|
|
"else " \
|
|
"echo WARN: Cannot load the DT; " \
|
|
"fi; " \
|
|
"fi; " \
|
|
"else " \
|
|
"bootz; " \
|
|
"fi;\0"
|
|
|
|
/* Miscellaneous configurable options */
|
|
|
|
/* Physical memory map */
|
|
#define PHYS_SDRAM (0x80000000)
|
|
#define PHYS_SDRAM_SIZE (128 * 1024 * 1024)
|
|
|
|
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
|
|
#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
|
|
#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
|
|
|
|
#ifdef CONFIG_ENV_IS_IN_NAND
|
|
#define CONFIG_ENV_RANGE (512 * 1024)
|
|
#endif
|
|
|
|
#endif
|