u-boot/arch/arm/dts/stm32429i-eval.dts
Patrice Chotard dd1e3e799a ARM: dts: stm32: limit sdio frequency to 14Mhz for stm32f429i-eval
This avoids the following errors while reading on mmc:
  Read data bytes CRC error: 0x2
  switch to partitions #0, OK
  mmc0 is current device
  Read data bytes CRC error: 0x82002
  ** Unrecognized filesystem type **

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-03-13 21:45:37 -04:00

277 lines
4.5 KiB
Text

/*
* Copyright (C) 2015, STMicroelectronics - All Rights Reserved
* Author: Maxime Coquelin <mcoquelin.stm32@gmail.com> for STMicroelectronics.
*
* SPDX-License-Identifier: GPL-2.0+
*/
/dts-v1/;
#include "stm32f429.dtsi"
#include "stm32f429-pinctrl.dtsi"
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/gpio.h>
/ {
model = "STMicroelectronics STM32429i-EVAL board";
compatible = "st,stm32429i-eval", "st,stm32f429";
chosen {
bootargs = "root=/dev/ram";
stdout-path = "serial0:115200n8";
};
memory {
reg = <0x00000000 0x2000000>;
};
aliases {
serial0 = &usart1;
};
clocks {
clk_ext_camera: clk-ext-camera {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
};
};
soc {
dma-ranges = <0xc0000000 0x0 0x10000000>;
};
regulators {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <0>;
reg_vref: regulator@0 {
compatible = "regulator-fixed";
reg = <0>;
regulator-name = "vref";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
};
leds {
compatible = "gpio-leds";
green {
gpios = <&gpiog 6 1>;
linux,default-trigger = "heartbeat";
};
orange {
gpios = <&gpiog 7 1>;
};
red {
gpios = <&gpiog 10 1>;
};
blue {
gpios = <&gpiog 12 1>;
};
};
gpio_keys {
compatible = "gpio-keys";
#address-cells = <1>;
#size-cells = <0>;
autorepeat;
button@0 {
label = "Wake up";
linux,code = <KEY_WAKEUP>;
gpios = <&gpioa 0 0>;
};
button@1 {
label = "Tamper";
linux,code = <KEY_RESTART>;
gpios = <&gpioc 13 0>;
};
};
usbotg_hs_phy: usbphy {
#phy-cells = <0>;
compatible = "usb-nop-xceiv";
clocks = <&rcc 0 STM32F4_AHB1_CLOCK(OTGHSULPI)>;
clock-names = "main_clk";
};
panel_rgb: panel-rgb {
compatible = "ampire,am-480272h3tmqw-t01h";
status = "okay";
port {
panel_in_rgb: endpoint {
remote-endpoint = <&ltdc_out_rgb>;
};
};
};
mmc_vcard: mmc_vcard {
compatible = "regulator-fixed";
regulator-name = "mmc_vcard";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
};
&adc {
pinctrl-names = "default";
pinctrl-0 = <&adc3_in8_pin>;
vref-supply = <&reg_vref>;
status = "okay";
adc3: adc@200 {
st,adc-channels = <8>;
status = "okay";
};
};
&clk_hse {
clock-frequency = <25000000>;
};
&crc {
status = "okay";
};
&dcmi {
status = "okay";
port {
dcmi_0: endpoint {
remote-endpoint = <&ov2640_0>;
bus-width = <8>;
hsync-active = <0>;
vsync-active = <0>;
pclk-sample = <1>;
};
};
};
&i2c1 {
pinctrl-0 = <&i2c1_pins>;
pinctrl-names = "default";
status = "okay";
ov2640: camera@30 {
compatible = "ovti,ov2640";
reg = <0x30>;
resetb-gpios = <&stmpegpio 2 GPIO_ACTIVE_HIGH>;
pwdn-gpios = <&stmpegpio 0 GPIO_ACTIVE_LOW>;
clocks = <&clk_ext_camera>;
clock-names = "xvclk";
status = "okay";
port {
ov2640_0: endpoint {
remote-endpoint = <&dcmi_0>;
};
};
};
stmpe1600: stmpe1600@42 {
compatible = "st,stmpe1600";
reg = <0x42>;
interrupts = <8 3>;
interrupt-parent = <&gpioi>;
interrupt-controller;
wakeup-source;
stmpegpio: stmpe_gpio {
compatible = "st,stmpe-gpio";
gpio-controller;
#gpio-cells = <2>;
};
};
};
&iwdg {
status = "okay";
timeout-sec = <32>;
};
&ltdc {
status = "okay";
pinctrl-0 = <&ltdc_pins>;
pinctrl-names = "default";
dma-ranges;
port {
ltdc_out_rgb: endpoint {
remote-endpoint = <&panel_in_rgb>;
};
};
};
&mac {
status = "okay";
pinctrl-0 = <&ethernet_mii>;
pinctrl-names = "default";
phy-mode = "mii";
phy-handle = <&phy1>;
mdio0 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "snps,dwmac-mdio";
phy1: ethernet-phy@1 {
reg = <1>;
};
};
};
&rtc {
status = "okay";
};
&sdio {
status = "okay";
vmmc-supply = <&mmc_vcard>;
cd-gpios = <&stmpegpio 15 GPIO_ACTIVE_HIGH>;
cd-inverted;
pinctrl-names = "default", "opendrain";
pinctrl-0 = <&sdio_pins>;
pinctrl-1 = <&sdio_pins_od>;
bus-width = <4>;
max-frequency = <14000000>;
};
&timers1 {
status = "okay";
pwm {
pinctrl-0 = <&pwm1_pins>;
pinctrl-names = "default";
status = "okay";
};
timer@0 {
status = "okay";
};
};
&timers3 {
status = "okay";
pwm {
pinctrl-0 = <&pwm3_pins>;
pinctrl-names = "default";
status = "okay";
};
timer@2 {
status = "okay";
};
};
&usart1 {
pinctrl-0 = <&usart1_pins_a>;
pinctrl-names = "default";
status = "okay";
};
&usbotg_hs {
dr_mode = "host";
phys = <&usbotg_hs_phy>;
phy-names = "usb2-phy";
pinctrl-0 = <&usbotg_hs_pins_a>;
pinctrl-names = "default";
status = "okay";
};