u-boot/board/compulab/cl-som-imx7/cl-som-imx7.c
Tom Rini 83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00

331 lines
7.9 KiB
C

// SPDX-License-Identifier: GPL-2.0+
/*
* U-Boot board functions for CompuLab CL-SOM-iMX7 module
*
* (C) Copyright 2017 CompuLab, Ltd. http://www.compulab.com
*
* Author: Uri Mashiach <uri.mashiach@compulab.co.il>
*/
#include <common.h>
#include <environment.h>
#include <mmc.h>
#include <phy.h>
#include <netdev.h>
#include <fsl_esdhc.h>
#include <power/pmic.h>
#include <power/pfuze3000_pmic.h>
#include <asm/mach-imx/mxc_i2c.h>
#include <asm/mach-imx/iomux-v3.h>
#include <asm/arch-mx7/mx7-pins.h>
#include <asm/arch-mx7/sys_proto.h>
#include <asm/arch-mx7/clock.h>
#include "../common/eeprom.h"
#include "common.h"
DECLARE_GLOBAL_DATA_PTR;
#ifdef CONFIG_SYS_I2C_MXC
#define I2C_PAD_CTRL (PAD_CTL_DSE_3P3V_32OHM | PAD_CTL_SRE_SLOW | \
PAD_CTL_HYS)
#define CL_SOM_IMX7_GPIO_I2C2_SCL IMX_GPIO_NR(1, 6)
#define CL_SOM_IMX7_GPIO_I2C2_SDA IMX_GPIO_NR(1, 7)
static struct i2c_pads_info cl_som_imx7_i2c_pad_info2 = {
.scl = {
.i2c_mode = MX7D_PAD_GPIO1_IO06__I2C2_SCL |
MUX_PAD_CTRL(I2C_PAD_CTRL),
.gpio_mode = MX7D_PAD_GPIO1_IO06__GPIO1_IO6 |
MUX_PAD_CTRL(I2C_PAD_CTRL),
.gp = CL_SOM_IMX7_GPIO_I2C2_SCL,
},
.sda = {
.i2c_mode = MX7D_PAD_GPIO1_IO07__I2C2_SDA |
MUX_PAD_CTRL(I2C_PAD_CTRL),
.gpio_mode = MX7D_PAD_GPIO1_IO07__GPIO1_IO7 |
MUX_PAD_CTRL(I2C_PAD_CTRL),
.gp = CL_SOM_IMX7_GPIO_I2C2_SDA,
},
};
/*
* cl_som_imx7_setup_i2c() - I2C pinmux configuration.
*/
static void cl_som_imx7_setup_i2c(void)
{
setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &cl_som_imx7_i2c_pad_info2);
}
#else /* !CONFIG_SYS_I2C_MXC */
static void cl_som_imx7_setup_i2c(void) {}
#endif /* CONFIG_SYS_I2C_MXC */
int dram_init(void)
{
gd->ram_size = imx_ddr_size();
return 0;
}
#ifdef CONFIG_FSL_ESDHC
#define CL_SOM_IMX7_GPIO_USDHC3_PWR IMX_GPIO_NR(6, 11)
static struct fsl_esdhc_cfg cl_som_imx7_usdhc_cfg[3] = {
{USDHC1_BASE_ADDR, 0, 4},
{USDHC3_BASE_ADDR},
};
int board_mmc_init(bd_t *bis)
{
int i, ret;
/*
* According to the board_mmc_init() the following map is done:
* (U-boot device node) (Physical Port)
* mmc0 USDHC1
* mmc2 USDHC3 (eMMC)
*/
for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
switch (i) {
case 0:
cl_som_imx7_usdhc1_pads_set();
gpio_request(CL_SOM_IMX7_GPIO_USDHC1_CD, "usdhc1_cd");
cl_som_imx7_usdhc_cfg[0].sdhc_clk =
mxc_get_clock(MXC_ESDHC_CLK);
break;
case 1:
cl_som_imx7_usdhc3_emmc_pads_set();
gpio_request(CL_SOM_IMX7_GPIO_USDHC3_PWR, "usdhc3_pwr");
gpio_direction_output(CL_SOM_IMX7_GPIO_USDHC3_PWR, 0);
udelay(500);
gpio_direction_output(CL_SOM_IMX7_GPIO_USDHC3_PWR, 1);
cl_som_imx7_usdhc_cfg[1].sdhc_clk =
mxc_get_clock(MXC_ESDHC3_CLK);
break;
default:
printf("Warning: you configured more USDHC controllers "
"(%d) than supported by the board\n", i + 1);
return -EINVAL;
}
ret = fsl_esdhc_initialize(bis, &cl_som_imx7_usdhc_cfg[i]);
if (ret)
return ret;
}
return 0;
}
#endif /* CONFIG_FSL_ESDHC */
#ifdef CONFIG_FEC_MXC
#define CL_SOM_IMX7_ETH1_PHY_NRST IMX_GPIO_NR(1, 4)
/*
* cl_som_imx7_rgmii_rework() - Ethernet PHY configuration.
*/
static void cl_som_imx7_rgmii_rework(struct phy_device *phydev)
{
unsigned short val;
/* Ar8031 phy SmartEEE feature cause link status generates glitch,
* which cause ethernet link down/up issue, so disable SmartEEE
*/
phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x3);
phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x805d);
phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4003);
val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
val &= ~(0x1 << 8);
phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
/* To enable AR8031 ouput a 125MHz clk from CLK_25M */
phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
val &= 0xffe3;
val |= 0x18;
phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
/* introduce tx clock delay */
phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
val |= 0x0100;
phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);
}
int board_phy_config(struct phy_device *phydev)
{
cl_som_imx7_rgmii_rework(phydev);
if (phydev->drv->config)
phydev->drv->config(phydev);
return 0;
}
/*
* cl_som_imx7_handle_mac_address() - set Ethernet MAC address environment.
*
* @env_var: MAC address environment variable
* @eeprom_bus: I2C bus of the environment EEPROM
*
* @return: 0 on success, < 0 on failure
*/
static int cl_som_imx7_handle_mac_address(char *env_var, uint eeprom_bus)
{
int ret;
unsigned char enetaddr[6];
ret = eth_env_get_enetaddr(env_var, enetaddr);
if (ret)
return 0;
ret = cl_eeprom_read_mac_addr(enetaddr, eeprom_bus);
if (ret)
return ret;
ret = is_valid_ethaddr(enetaddr);
if (!ret)
return -1;
return eth_env_set_enetaddr(env_var, enetaddr);
}
#define CL_SOM_IMX7_FEC_DEV_ID_PRI 0
int board_eth_init(bd_t *bis)
{
/* set Ethernet MAC address environment */
cl_som_imx7_handle_mac_address("ethaddr", CONFIG_SYS_I2C_EEPROM_BUS);
/* Ethernet interface pinmux configuration */
cl_som_imx7_phy1_rst_pads_set();
cl_som_imx7_fec1_pads_set();
/* PHY reset */
gpio_request(CL_SOM_IMX7_ETH1_PHY_NRST, "eth1_phy_nrst");
gpio_direction_output(CL_SOM_IMX7_ETH1_PHY_NRST, 0);
mdelay(10);
gpio_set_value(CL_SOM_IMX7_ETH1_PHY_NRST, 1);
/* MAC initialization */
return fecmxc_initialize_multi(bis, CL_SOM_IMX7_FEC_DEV_ID_PRI,
CONFIG_FEC_MXC_PHYADDR, IMX_FEC_BASE);
}
/*
* cl_som_imx7_setup_fec() - Ethernet MAC 1 clock configuration.
* - ENET1 reference clock mode select.
* - ENET1_TX_CLK output driver is disabled when configured for ALT1.
*/
static void cl_som_imx7_setup_fec(void)
{
struct iomuxc_gpr_base_regs *const iomuxc_gpr_regs
= (struct iomuxc_gpr_base_regs *)IOMUXC_GPR_BASE_ADDR;
/* Use 125M anatop REF_CLK1 for ENET1, clear gpr1[13], gpr1[17]*/
clrsetbits_le32(&iomuxc_gpr_regs->gpr[1],
(IOMUXC_GPR_GPR1_GPR_ENET1_TX_CLK_SEL_MASK |
IOMUXC_GPR_GPR1_GPR_ENET1_CLK_DIR_MASK), 0);
set_clk_enet(ENET_125MHZ);
}
#else /* !CONFIG_FEC_MXC */
static void cl_som_imx7_setup_fec(void) {}
#endif /* CONFIG_FEC_MXC */
#ifdef CONFIG_SPI
static void cl_som_imx7_spi_init(void)
{
cl_som_imx7_espi1_pads_set();
}
#else /* !CONFIG_SPI */
static void cl_som_imx7_spi_init(void) {}
#endif /* CONFIG_SPI */
int board_early_init_f(void)
{
cl_som_imx7_uart1_pads_set();
cl_som_imx7_usb_otg1_pads_set();
return 0;
}
int board_init(void)
{
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
cl_som_imx7_setup_i2c();
cl_som_imx7_setup_fec();
cl_som_imx7_spi_init();
return 0;
}
#ifdef CONFIG_POWER
#define I2C_PMIC 0
int power_init_board(void)
{
struct pmic *p;
int ret;
unsigned int reg, rev_id;
ret = power_pfuze3000_init(I2C_PMIC);
if (ret)
return ret;
p = pmic_get("PFUZE3000");
ret = pmic_probe(p);
if (ret)
return ret;
pmic_reg_read(p, PFUZE3000_DEVICEID, &reg);
pmic_reg_read(p, PFUZE3000_REVID, &rev_id);
printf("PMIC: PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", reg, rev_id);
/* disable Low Power Mode during standby mode */
pmic_reg_write(p, PFUZE3000_LDOGCTL, 0x1);
return 0;
}
#endif /* CONFIG_POWER */
/*
* cl_som_imx7_setup_wdog() - watchdog configuration.
* - Output WDOG_B signal to reset external pmic.
* - Suspend the watchdog timer during low-power modes.
*/
void cl_som_imx7_setup_wdog(void)
{
struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR;
cl_som_imx7_wdog_pads_set();
set_wdog_reset(wdog);
/*
* Do not assert internal WDOG_RESET_B_DEB(controlled by bit 4),
* since we use PMIC_PWRON to reset the board.
*/
clrsetbits_le16(&wdog->wcr, 0, 0x10);
}
int board_late_init(void)
{
env_set("board_name", "CL-SOM-iMX7");
cl_som_imx7_setup_wdog();
return 0;
}
int checkboard(void)
{
char *mode;
if (IS_ENABLED(CONFIG_ARMV7_BOOT_SEC_DEFAULT))
mode = "secure";
else
mode = "non-secure";
printf("Board: CL-SOM-iMX7 in %s mode\n", mode);
return 0;
}