u-boot/configs/sama5d27_wlsom1_ek_qspiflash_defconfig
Anatolij Gustschin 2cc393f32f video: make BPP and ANSI configs optional
Many boards do not use all selected framebuffer depth
configurations, for such boards there is some unused
code in video and console uclass routines. Make depth
specific code optional to avoid dead code and slightly
reduce binary size. Also make ANSI code optional for
the same reason. When i.e. using only VIDEO_BPP16 the
code size shrinks (below values when using gcc-7.3.0):

  $ ./tools/buildman/buildman -b video-wip -sS wandboard
  ...
  01: Merge git://git.denx.de/u-boot-sh
  02: video: add guards around 16bpp/32bbp code
  03: video: make BPP and ANSI configs optional
         arm: (for 1/1 boards) all -776.0 bss -8.0 text -768.0

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Eugen Hristev <eugen.hristev@microchip.com>
Tested-by: Patrice Chotard <patrice.chotard@st.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
2019-12-06 16:38:51 +01:00

118 lines
2.8 KiB
Text

CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_SYS_TEXT_BASE=0x26f00000
CONFIG_TARGET_SAMA5D27_WLSOM1_EK=y
CONFIG_SPL_GPIO_SUPPORT=y
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_SPL_SERIAL_SUPPORT=y
CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
CONFIG_SPL=y
CONFIG_DEBUG_UART_BOARD_INIT=y
CONFIG_DEBUG_UART_BASE=0xf801c000
CONFIG_DEBUG_UART_CLOCK=82000000
CONFIG_ENV_SECT_SIZE=0x1000
CONFIG_SPL_SPI_FLASH_SUPPORT=y
CONFIG_SPL_SPI_SUPPORT=y
CONFIG_DEBUG_UART=y
CONFIG_SPL_TEXT_BASE=0x200000
CONFIG_ENV_VARS_UBOOT_CONFIG=y
CONFIG_FIT=y
CONFIG_SYS_EXTRA_OPTIONS="SAMA5D2"
CONFIG_QSPI_BOOT=y
CONFIG_SPI_BOOT=y
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_MISC_INIT_R=y
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_DISPLAY_BOARDINFO_LATE=y
CONFIG_SPL_SEPARATE_BSS=y
CONFIG_SPL_DISPLAY_PRINT=y
# CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR is not set
CONFIG_SPL_SPI_LOAD=y
CONFIG_SYS_SPI_U_BOOT_OFFS=0x40000
CONFIG_SPL_AT91_MCK_BYPASS=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_BOOTZ=y
# CONFIG_CMD_FLASH is not set
CONFIG_CMD_I2C=y
# CONFIG_CMD_LOADS is not set
CONFIG_CMD_MMC=y
CONFIG_CMD_USB=y
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_FAT=y
CONFIG_OF_CONTROL=y
CONFIG_SPL_OF_CONTROL=y
CONFIG_DEFAULT_DEVICE_TREE="at91-sama5d27_wlsom1_ek"
CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-parent dmas dma-names"
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_USE_ENV_SPI_BUS=y
CONFIG_ENV_SPI_BUS=2
CONFIG_USE_ENV_SPI_CS=y
CONFIG_ENV_SPI_CS=0
CONFIG_USE_ENV_SPI_MAX_HZ=y
CONFIG_ENV_SPI_MAX_HZ=50000000
CONFIG_USE_ENV_SPI_MODE=y
CONFIG_ENV_SPI_MODE=0x0
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_DM=y
CONFIG_SPL_DM=y
CONFIG_SPL_DM_SEQ_ALIAS=y
CONFIG_CLK=y
CONFIG_SPL_CLK=y
CONFIG_CLK_AT91=y
CONFIG_AT91_UTMI=y
CONFIG_AT91_H32MX=y
CONFIG_AT91_GENERIC_CLK=y
CONFIG_DM_GPIO=y
CONFIG_ATMEL_PIO4=y
CONFIG_DM_I2C=y
CONFIG_SYS_I2C_AT91=y
CONFIG_I2C_EEPROM=y
CONFIG_DM_MMC=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ATMEL=y
CONFIG_MTD=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SF_DEFAULT_BUS=2
CONFIG_SF_DEFAULT_SPEED=50000000
CONFIG_SPI_FLASH_ATMEL=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_SPI_FLASH_SST=y
CONFIG_PHY_MICREL=y
CONFIG_DM_ETH=y
CONFIG_MACB=y
CONFIG_PINCTRL=y
CONFIG_SPL_PINCTRL=y
CONFIG_PINCTRL_AT91PIO4=y
CONFIG_DM_SERIAL=y
CONFIG_DEBUG_UART_ATMEL=y
CONFIG_DEBUG_UART_ANNOUNCE=y
CONFIG_ATMEL_USART=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
CONFIG_ATMEL_QSPI=y
CONFIG_TIMER=y
CONFIG_SPL_TIMER=y
CONFIG_ATMEL_PIT_TIMER=y
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_USB_GADGET_ATMEL_USBA=y
CONFIG_DM_VIDEO=y
CONFIG_VIDEO_BPP16=y
CONFIG_ATMEL_HLCD=y
CONFIG_W1=y
CONFIG_W1_GPIO=y
CONFIG_W1_EEPROM=y
CONFIG_W1_EEPROM_DS24XXX=y
CONFIG_OF_LIBFDT_OVERLAY=y
# CONFIG_EFI_LOADER_HII is not set