mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-14 08:57:58 +00:00
5e165b258f
The max size of available memories on slot0 and slot1 is 32MB because - EA[25] signal is not output on the save-pin mode which is used PH1-LD4 or later SoCs. - EA[25] signal is not connected by the limitation (or bug?) of the PLD logic of DCC support card. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
225 lines
5 KiB
C
225 lines
5 KiB
C
/*
|
|
* Copyright (C) 2012-2014 Panasonic Corporation
|
|
* Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/board.h>
|
|
|
|
#if defined(CONFIG_PFC_MICRO_SUPPORT_CARD)
|
|
|
|
#define PFC_MICRO_SUPPORT_CARD_RESET \
|
|
((CONFIG_SUPPORT_CARD_BASE) + 0x000D0034)
|
|
#define PFC_MICRO_SUPPORT_CARD_REVISION \
|
|
((CONFIG_SUPPORT_CARD_BASE) + 0x000D00E0)
|
|
/*
|
|
* 0: reset deassert, 1: reset
|
|
*
|
|
* bit[0]: LAN, I2C, LED
|
|
* bit[1]: UART
|
|
*/
|
|
void support_card_reset_deassert(void)
|
|
{
|
|
writel(0, PFC_MICRO_SUPPORT_CARD_RESET);
|
|
}
|
|
|
|
void support_card_reset(void)
|
|
{
|
|
writel(3, PFC_MICRO_SUPPORT_CARD_RESET);
|
|
}
|
|
|
|
static int support_card_show_revision(void)
|
|
{
|
|
u32 revision;
|
|
|
|
revision = readl(PFC_MICRO_SUPPORT_CARD_REVISION);
|
|
printf("(PFC CPLD version %d.%d)\n", revision >> 4, revision & 0xf);
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
#if defined(CONFIG_DCC_MICRO_SUPPORT_CARD)
|
|
|
|
#define DCC_MICRO_SUPPORT_CARD_RESET_LAN \
|
|
((CONFIG_SUPPORT_CARD_BASE) + 0x00401300)
|
|
#define DCC_MICRO_SUPPORT_CARD_RESET_UART \
|
|
((CONFIG_SUPPORT_CARD_BASE) + 0x00401304)
|
|
#define DCC_MICRO_SUPPORT_CARD_RESET_I2C \
|
|
((CONFIG_SUPPORT_CARD_BASE) + 0x00401308)
|
|
#define DCC_MICRO_SUPPORT_CARD_REVISION \
|
|
((CONFIG_SUPPORT_CARD_BASE) + 0x005000E0)
|
|
|
|
void support_card_reset_deassert(void)
|
|
{
|
|
writel(1, DCC_MICRO_SUPPORT_CARD_RESET_LAN); /* LAN and LED */
|
|
writel(1, DCC_MICRO_SUPPORT_CARD_RESET_UART); /* UART */
|
|
writel(1, DCC_MICRO_SUPPORT_CARD_RESET_I2C); /* I2C */
|
|
}
|
|
|
|
void support_card_reset(void)
|
|
{
|
|
writel(0, DCC_MICRO_SUPPORT_CARD_RESET_LAN); /* LAN and LED */
|
|
writel(0, DCC_MICRO_SUPPORT_CARD_RESET_UART); /* UART */
|
|
writel(0, DCC_MICRO_SUPPORT_CARD_RESET_I2C); /* I2C */
|
|
}
|
|
|
|
static int support_card_show_revision(void)
|
|
{
|
|
u32 revision;
|
|
|
|
revision = readl(DCC_MICRO_SUPPORT_CARD_REVISION);
|
|
|
|
if (revision >= 0x67) {
|
|
printf("(DCC CPLD version 3.%d.%d)\n",
|
|
revision >> 4, revision & 0xf);
|
|
return 0;
|
|
} else {
|
|
printf("(DCC CPLD unknown version)\n");
|
|
return -1;
|
|
}
|
|
}
|
|
#endif
|
|
|
|
int check_support_card(void)
|
|
{
|
|
printf("SC: Micro Support Card ");
|
|
return support_card_show_revision();
|
|
}
|
|
|
|
void support_card_init(void)
|
|
{
|
|
/*
|
|
* After power on, we need to keep the LAN controller in reset state
|
|
* for a while. (200 usec)
|
|
* Fortunatelly, enough wait time is already inserted in pll_init()
|
|
* function. So we do not have to wait here.
|
|
*/
|
|
support_card_reset_deassert();
|
|
}
|
|
|
|
#if defined(CONFIG_SMC911X)
|
|
#include <netdev.h>
|
|
|
|
int board_eth_init(bd_t *bis)
|
|
{
|
|
return smc911x_initialize(0, CONFIG_SMC911X_BASE);
|
|
}
|
|
#endif
|
|
|
|
#if !defined(CONFIG_SYS_NO_FLASH)
|
|
|
|
#include <mtd/cfi_flash.h>
|
|
#include <asm/arch/sbc-regs.h>
|
|
|
|
struct memory_bank {
|
|
phys_addr_t base;
|
|
unsigned long size;
|
|
};
|
|
|
|
static int mem_is_flash(const struct memory_bank *mem)
|
|
{
|
|
const int loop = 128;
|
|
u32 *scratch_addr;
|
|
u32 saved_value;
|
|
int ret = 1;
|
|
int i;
|
|
|
|
/* just in case, use the tail of the memory bank */
|
|
scratch_addr = map_physmem(mem->base + mem->size - sizeof(u32) * loop,
|
|
sizeof(u32) * loop, MAP_NOCACHE);
|
|
|
|
for (i = 0; i < loop; i++, scratch_addr++) {
|
|
saved_value = readl(scratch_addr);
|
|
writel(~saved_value, scratch_addr);
|
|
if (readl(scratch_addr) != saved_value) {
|
|
/* We assume no memory or SRAM here. */
|
|
writel(saved_value, scratch_addr);
|
|
ret = 0;
|
|
break;
|
|
}
|
|
}
|
|
|
|
unmap_physmem(scratch_addr, MAP_NOCACHE);
|
|
|
|
return ret;
|
|
}
|
|
|
|
#if defined(CONFIG_PFC_MICRO_SUPPORT_CARD)
|
|
/* {address, size} */
|
|
static const struct memory_bank memory_banks_boot_swap_off[] = {
|
|
{0x02000000, 0x01f00000},
|
|
};
|
|
|
|
static const struct memory_bank memory_banks_boot_swap_on[] = {
|
|
{0x00000000, 0x01f00000},
|
|
};
|
|
#endif
|
|
|
|
#if defined(CONFIG_DCC_MICRO_SUPPORT_CARD)
|
|
static const struct memory_bank memory_banks_boot_swap_off[] = {
|
|
{0x04000000, 0x02000000},
|
|
};
|
|
|
|
static const struct memory_bank memory_banks_boot_swap_on[] = {
|
|
{0x00000000, 0x02000000},
|
|
{0x04000000, 0x02000000},
|
|
};
|
|
#endif
|
|
|
|
static const struct memory_bank
|
|
*flash_banks_list[CONFIG_SYS_MAX_FLASH_BANKS_DETECT];
|
|
|
|
phys_addr_t cfi_flash_bank_addr(int i)
|
|
{
|
|
return flash_banks_list[i]->base;
|
|
}
|
|
|
|
unsigned long cfi_flash_bank_size(int i)
|
|
{
|
|
return flash_banks_list[i]->size;
|
|
}
|
|
|
|
static void detect_num_flash_banks(void)
|
|
{
|
|
const struct memory_bank *memory_bank, *end;
|
|
|
|
cfi_flash_num_flash_banks = 0;
|
|
|
|
if (boot_is_swapped()) {
|
|
memory_bank = memory_banks_boot_swap_on;
|
|
end = memory_bank + ARRAY_SIZE(memory_banks_boot_swap_on);
|
|
} else {
|
|
memory_bank = memory_banks_boot_swap_off;
|
|
end = memory_bank + ARRAY_SIZE(memory_banks_boot_swap_off);
|
|
}
|
|
|
|
for (; memory_bank < end; memory_bank++) {
|
|
if (cfi_flash_num_flash_banks >=
|
|
CONFIG_SYS_MAX_FLASH_BANKS_DETECT)
|
|
break;
|
|
|
|
if (mem_is_flash(memory_bank)) {
|
|
flash_banks_list[cfi_flash_num_flash_banks] =
|
|
memory_bank;
|
|
|
|
debug("flash bank found: base = 0x%lx, size = 0x%lx\n",
|
|
memory_bank->base, memory_bank->size);
|
|
cfi_flash_num_flash_banks++;
|
|
}
|
|
}
|
|
|
|
debug("number of flash banks: %d\n", cfi_flash_num_flash_banks);
|
|
}
|
|
#else /* ONFIG_SYS_NO_FLASH */
|
|
void detect_num_flash_banks(void)
|
|
{
|
|
};
|
|
#endif /* ONFIG_SYS_NO_FLASH */
|
|
|
|
void support_card_late_init(void)
|
|
{
|
|
detect_num_flash_banks();
|
|
}
|