mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-01 17:10:11 +00:00
20af5adf22
Adds a short bindings document describing the expected structure of a MDIO MUX dts node. This is based on Linux binding and the example is in fact copied from there. Signed-off-by: Alex Marginean <alexm.osslist@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
138 lines
4.1 KiB
Text
138 lines
4.1 KiB
Text
The expected structure of an MDIO MUX device tree node is described here. This
|
|
is heavily based on current Linux specification.
|
|
One notable difference to Linux is that mdio-parent-bus is currently required
|
|
by U-Boot, not optional as is in Linux. Current U-Boot MDIO MUX udevice class
|
|
implementation does not have specific support for MDIOs with an integrated MUX,
|
|
the property should be made optional if such support is added.
|
|
|
|
The MDIO buses downstream of the MUX should be described in the device tree as
|
|
child nodes as indicated below.
|
|
|
|
Required properties:
|
|
mdio-parent-bus = a phandle to the MDIO bus used to perform actual I/O. This is
|
|
typically a real MDIO device, unless there are cascaded MUXes.
|
|
#address-cells = <1>, each MDIO group is identified by one 32b value.
|
|
#size-cells = <0>
|
|
|
|
Other properties:
|
|
The properties described here are sufficient for MDIO MUX DM class code, but
|
|
MUX drivers may define additional properties, either required or optional.
|
|
|
|
Required properties in child nodes:
|
|
reg = value to be configured on the MUX to select the respective downstream
|
|
MDIO.
|
|
|
|
Child nodes should normally contain PHY nodes, referenced by phandle from
|
|
ethernet nodes of the eth interfaces using these PHYs.
|
|
|
|
Example structure, extracted from Linux bindings document:
|
|
|
|
/* The parent MDIO bus. */
|
|
smi1: mdio@1180000001900 {
|
|
compatible = "cavium,octeon-3860-mdio";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <0x11800 0x00001900 0x0 0x40>;
|
|
};
|
|
/*
|
|
* An NXP sn74cbtlv3253 dual 1-of-4 switch controlled by a
|
|
* pair of GPIO lines. Child busses 2 and 3 populated with 4
|
|
* PHYs each.
|
|
*/
|
|
mdio-mux {
|
|
compatible = "mdio-mux-gpio";
|
|
gpios = <&gpio1 3 0>, <&gpio1 4 0>;
|
|
mdio-parent-bus = <&smi1>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
mdio@2 {
|
|
reg = <2>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
phy11: ethernet-phy@1 {
|
|
reg = <1>;
|
|
compatible = "marvell,88e1149r";
|
|
marvell,reg-init = <3 0x10 0 0x5777>,
|
|
<3 0x11 0 0x00aa>,
|
|
<3 0x12 0 0x4105>,
|
|
<3 0x13 0 0x0a60>;
|
|
interrupt-parent = <&gpio>;
|
|
interrupts = <10 8>; /* Pin 10, active low */
|
|
};
|
|
phy12: ethernet-phy@2 {
|
|
reg = <2>;
|
|
compatible = "marvell,88e1149r";
|
|
marvell,reg-init = <3 0x10 0 0x5777>,
|
|
<3 0x11 0 0x00aa>,
|
|
<3 0x12 0 0x4105>,
|
|
<3 0x13 0 0x0a60>;
|
|
interrupt-parent = <&gpio>;
|
|
interrupts = <10 8>; /* Pin 10, active low */
|
|
};
|
|
phy13: ethernet-phy@3 {
|
|
reg = <3>;
|
|
compatible = "marvell,88e1149r";
|
|
marvell,reg-init = <3 0x10 0 0x5777>,
|
|
<3 0x11 0 0x00aa>,
|
|
<3 0x12 0 0x4105>,
|
|
<3 0x13 0 0x0a60>;
|
|
interrupt-parent = <&gpio>;
|
|
interrupts = <10 8>; /* Pin 10, active low */
|
|
};
|
|
phy14: ethernet-phy@4 {
|
|
reg = <4>;
|
|
compatible = "marvell,88e1149r";
|
|
marvell,reg-init = <3 0x10 0 0x5777>,
|
|
<3 0x11 0 0x00aa>,
|
|
<3 0x12 0 0x4105>,
|
|
<3 0x13 0 0x0a60>;
|
|
interrupt-parent = <&gpio>;
|
|
interrupts = <10 8>; /* Pin 10, active low */
|
|
};
|
|
};
|
|
mdio@3 {
|
|
reg = <3>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
phy21: ethernet-phy@1 {
|
|
reg = <1>;
|
|
compatible = "marvell,88e1149r";
|
|
marvell,reg-init = <3 0x10 0 0x5777>,
|
|
<3 0x11 0 0x00aa>,
|
|
<3 0x12 0 0x4105>,
|
|
<3 0x13 0 0x0a60>;
|
|
interrupt-parent = <&gpio>;
|
|
interrupts = <12 8>; /* Pin 12, active low */
|
|
};
|
|
phy22: ethernet-phy@2 {
|
|
reg = <2>;
|
|
compatible = "marvell,88e1149r";
|
|
marvell,reg-init = <3 0x10 0 0x5777>,
|
|
<3 0x11 0 0x00aa>,
|
|
<3 0x12 0 0x4105>,
|
|
<3 0x13 0 0x0a60>;
|
|
interrupt-parent = <&gpio>;
|
|
interrupts = <12 8>; /* Pin 12, active low */
|
|
};
|
|
phy23: ethernet-phy@3 {
|
|
reg = <3>;
|
|
compatible = "marvell,88e1149r";
|
|
marvell,reg-init = <3 0x10 0 0x5777>,
|
|
<3 0x11 0 0x00aa>,
|
|
<3 0x12 0 0x4105>,
|
|
<3 0x13 0 0x0a60>;
|
|
interrupt-parent = <&gpio>;
|
|
interrupts = <12 8>; /* Pin 12, active low */
|
|
};
|
|
phy24: ethernet-phy@4 {
|
|
reg = <4>;
|
|
compatible = "marvell,88e1149r";
|
|
marvell,reg-init = <3 0x10 0 0x5777>,
|
|
<3 0x11 0 0x00aa>,
|
|
<3 0x12 0 0x4105>,
|
|
<3 0x13 0 0x0a60>;
|
|
interrupt-parent = <&gpio>;
|
|
interrupts = <12 8>; /* Pin 12, active low */
|
|
};
|
|
};
|
|
};
|