u-boot/drivers/net/mvneta.c
Matt Pelland 0a85f024c5 net: mvneta: support setting hardware address
mvneta already supports setting the MAC address but this was only done
internally when some other part of U-Boot tries to actually use the
interface. This commit exposes this functionality to the ethernet core
code so that the MAC addresses of all interfaces are configured
correctly even if they are not used before loading Linux.

Signed-off-by: Matt Pelland <mpelland@starry.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-13 15:47:31 -05:00

1805 lines
50 KiB
C

/*
* Driver for Marvell NETA network card for Armada XP and Armada 370 SoCs.
*
* U-Boot version:
* Copyright (C) 2014-2015 Stefan Roese <sr@denx.de>
*
* Based on the Linux version which is:
* Copyright (C) 2012 Marvell
*
* Rami Rosen <rosenr@marvell.com>
* Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
*
* SPDX-License-Identifier: GPL-2.0
*/
#include <common.h>
#include <dm.h>
#include <net.h>
#include <netdev.h>
#include <config.h>
#include <malloc.h>
#include <asm/io.h>
#include <linux/errno.h>
#include <phy.h>
#include <miiphy.h>
#include <watchdog.h>
#include <asm/arch/cpu.h>
#include <asm/arch/soc.h>
#include <linux/compat.h>
#include <linux/mbus.h>
DECLARE_GLOBAL_DATA_PTR;
#if !defined(CONFIG_PHYLIB)
# error Marvell mvneta requires PHYLIB
#endif
/* Some linux -> U-Boot compatibility stuff */
#define netdev_err(dev, fmt, args...) \
printf(fmt, ##args)
#define netdev_warn(dev, fmt, args...) \
printf(fmt, ##args)
#define netdev_info(dev, fmt, args...) \
printf(fmt, ##args)
#define CONFIG_NR_CPUS 1
#define ETH_HLEN 14 /* Total octets in header */
/* 2(HW hdr) 14(MAC hdr) 4(CRC) 32(extra for cache prefetch) */
#define WRAP (2 + ETH_HLEN + 4 + 32)
#define MTU 1500
#define RX_BUFFER_SIZE (ALIGN(MTU + WRAP, ARCH_DMA_MINALIGN))
#define MVNETA_SMI_TIMEOUT 10000
/* Registers */
#define MVNETA_RXQ_CONFIG_REG(q) (0x1400 + ((q) << 2))
#define MVNETA_RXQ_HW_BUF_ALLOC BIT(1)
#define MVNETA_RXQ_PKT_OFFSET_ALL_MASK (0xf << 8)
#define MVNETA_RXQ_PKT_OFFSET_MASK(offs) ((offs) << 8)
#define MVNETA_RXQ_THRESHOLD_REG(q) (0x14c0 + ((q) << 2))
#define MVNETA_RXQ_NON_OCCUPIED(v) ((v) << 16)
#define MVNETA_RXQ_BASE_ADDR_REG(q) (0x1480 + ((q) << 2))
#define MVNETA_RXQ_SIZE_REG(q) (0x14a0 + ((q) << 2))
#define MVNETA_RXQ_BUF_SIZE_SHIFT 19
#define MVNETA_RXQ_BUF_SIZE_MASK (0x1fff << 19)
#define MVNETA_RXQ_STATUS_REG(q) (0x14e0 + ((q) << 2))
#define MVNETA_RXQ_OCCUPIED_ALL_MASK 0x3fff
#define MVNETA_RXQ_STATUS_UPDATE_REG(q) (0x1500 + ((q) << 2))
#define MVNETA_RXQ_ADD_NON_OCCUPIED_SHIFT 16
#define MVNETA_RXQ_ADD_NON_OCCUPIED_MAX 255
#define MVNETA_PORT_RX_RESET 0x1cc0
#define MVNETA_PORT_RX_DMA_RESET BIT(0)
#define MVNETA_PHY_ADDR 0x2000
#define MVNETA_PHY_ADDR_MASK 0x1f
#define MVNETA_SMI 0x2004
#define MVNETA_PHY_REG_MASK 0x1f
/* SMI register fields */
#define MVNETA_SMI_DATA_OFFS 0 /* Data */
#define MVNETA_SMI_DATA_MASK (0xffff << MVNETA_SMI_DATA_OFFS)
#define MVNETA_SMI_DEV_ADDR_OFFS 16 /* PHY device address */
#define MVNETA_SMI_REG_ADDR_OFFS 21 /* PHY device reg addr*/
#define MVNETA_SMI_OPCODE_OFFS 26 /* Write/Read opcode */
#define MVNETA_SMI_OPCODE_READ (1 << MVNETA_SMI_OPCODE_OFFS)
#define MVNETA_SMI_READ_VALID (1 << 27) /* Read Valid */
#define MVNETA_SMI_BUSY (1 << 28) /* Busy */
#define MVNETA_MBUS_RETRY 0x2010
#define MVNETA_UNIT_INTR_CAUSE 0x2080
#define MVNETA_UNIT_CONTROL 0x20B0
#define MVNETA_PHY_POLLING_ENABLE BIT(1)
#define MVNETA_WIN_BASE(w) (0x2200 + ((w) << 3))
#define MVNETA_WIN_SIZE(w) (0x2204 + ((w) << 3))
#define MVNETA_WIN_REMAP(w) (0x2280 + ((w) << 2))
#define MVNETA_WIN_SIZE_MASK (0xffff0000)
#define MVNETA_BASE_ADDR_ENABLE 0x2290
#define MVNETA_BASE_ADDR_ENABLE_BIT 0x1
#define MVNETA_PORT_ACCESS_PROTECT 0x2294
#define MVNETA_PORT_ACCESS_PROTECT_WIN0_RW 0x3
#define MVNETA_PORT_CONFIG 0x2400
#define MVNETA_UNI_PROMISC_MODE BIT(0)
#define MVNETA_DEF_RXQ(q) ((q) << 1)
#define MVNETA_DEF_RXQ_ARP(q) ((q) << 4)
#define MVNETA_TX_UNSET_ERR_SUM BIT(12)
#define MVNETA_DEF_RXQ_TCP(q) ((q) << 16)
#define MVNETA_DEF_RXQ_UDP(q) ((q) << 19)
#define MVNETA_DEF_RXQ_BPDU(q) ((q) << 22)
#define MVNETA_RX_CSUM_WITH_PSEUDO_HDR BIT(25)
#define MVNETA_PORT_CONFIG_DEFL_VALUE(q) (MVNETA_DEF_RXQ(q) | \
MVNETA_DEF_RXQ_ARP(q) | \
MVNETA_DEF_RXQ_TCP(q) | \
MVNETA_DEF_RXQ_UDP(q) | \
MVNETA_DEF_RXQ_BPDU(q) | \
MVNETA_TX_UNSET_ERR_SUM | \
MVNETA_RX_CSUM_WITH_PSEUDO_HDR)
#define MVNETA_PORT_CONFIG_EXTEND 0x2404
#define MVNETA_MAC_ADDR_LOW 0x2414
#define MVNETA_MAC_ADDR_HIGH 0x2418
#define MVNETA_SDMA_CONFIG 0x241c
#define MVNETA_SDMA_BRST_SIZE_16 4
#define MVNETA_RX_BRST_SZ_MASK(burst) ((burst) << 1)
#define MVNETA_RX_NO_DATA_SWAP BIT(4)
#define MVNETA_TX_NO_DATA_SWAP BIT(5)
#define MVNETA_DESC_SWAP BIT(6)
#define MVNETA_TX_BRST_SZ_MASK(burst) ((burst) << 22)
#define MVNETA_PORT_STATUS 0x2444
#define MVNETA_TX_IN_PRGRS BIT(1)
#define MVNETA_TX_FIFO_EMPTY BIT(8)
#define MVNETA_RX_MIN_FRAME_SIZE 0x247c
#define MVNETA_SERDES_CFG 0x24A0
#define MVNETA_SGMII_SERDES_PROTO 0x0cc7
#define MVNETA_QSGMII_SERDES_PROTO 0x0667
#define MVNETA_TYPE_PRIO 0x24bc
#define MVNETA_FORCE_UNI BIT(21)
#define MVNETA_TXQ_CMD_1 0x24e4
#define MVNETA_TXQ_CMD 0x2448
#define MVNETA_TXQ_DISABLE_SHIFT 8
#define MVNETA_TXQ_ENABLE_MASK 0x000000ff
#define MVNETA_ACC_MODE 0x2500
#define MVNETA_CPU_MAP(cpu) (0x2540 + ((cpu) << 2))
#define MVNETA_CPU_RXQ_ACCESS_ALL_MASK 0x000000ff
#define MVNETA_CPU_TXQ_ACCESS_ALL_MASK 0x0000ff00
#define MVNETA_RXQ_TIME_COAL_REG(q) (0x2580 + ((q) << 2))
/* Exception Interrupt Port/Queue Cause register */
#define MVNETA_INTR_NEW_CAUSE 0x25a0
#define MVNETA_INTR_NEW_MASK 0x25a4
/* bits 0..7 = TXQ SENT, one bit per queue.
* bits 8..15 = RXQ OCCUP, one bit per queue.
* bits 16..23 = RXQ FREE, one bit per queue.
* bit 29 = OLD_REG_SUM, see old reg ?
* bit 30 = TX_ERR_SUM, one bit for 4 ports
* bit 31 = MISC_SUM, one bit for 4 ports
*/
#define MVNETA_TX_INTR_MASK(nr_txqs) (((1 << nr_txqs) - 1) << 0)
#define MVNETA_TX_INTR_MASK_ALL (0xff << 0)
#define MVNETA_RX_INTR_MASK(nr_rxqs) (((1 << nr_rxqs) - 1) << 8)
#define MVNETA_RX_INTR_MASK_ALL (0xff << 8)
#define MVNETA_INTR_OLD_CAUSE 0x25a8
#define MVNETA_INTR_OLD_MASK 0x25ac
/* Data Path Port/Queue Cause Register */
#define MVNETA_INTR_MISC_CAUSE 0x25b0
#define MVNETA_INTR_MISC_MASK 0x25b4
#define MVNETA_INTR_ENABLE 0x25b8
#define MVNETA_RXQ_CMD 0x2680
#define MVNETA_RXQ_DISABLE_SHIFT 8
#define MVNETA_RXQ_ENABLE_MASK 0x000000ff
#define MVETH_TXQ_TOKEN_COUNT_REG(q) (0x2700 + ((q) << 4))
#define MVETH_TXQ_TOKEN_CFG_REG(q) (0x2704 + ((q) << 4))
#define MVNETA_GMAC_CTRL_0 0x2c00
#define MVNETA_GMAC_MAX_RX_SIZE_SHIFT 2
#define MVNETA_GMAC_MAX_RX_SIZE_MASK 0x7ffc
#define MVNETA_GMAC0_PORT_ENABLE BIT(0)
#define MVNETA_GMAC_CTRL_2 0x2c08
#define MVNETA_GMAC2_PCS_ENABLE BIT(3)
#define MVNETA_GMAC2_PORT_RGMII BIT(4)
#define MVNETA_GMAC2_PORT_RESET BIT(6)
#define MVNETA_GMAC_STATUS 0x2c10
#define MVNETA_GMAC_LINK_UP BIT(0)
#define MVNETA_GMAC_SPEED_1000 BIT(1)
#define MVNETA_GMAC_SPEED_100 BIT(2)
#define MVNETA_GMAC_FULL_DUPLEX BIT(3)
#define MVNETA_GMAC_RX_FLOW_CTRL_ENABLE BIT(4)
#define MVNETA_GMAC_TX_FLOW_CTRL_ENABLE BIT(5)
#define MVNETA_GMAC_RX_FLOW_CTRL_ACTIVE BIT(6)
#define MVNETA_GMAC_TX_FLOW_CTRL_ACTIVE BIT(7)
#define MVNETA_GMAC_AUTONEG_CONFIG 0x2c0c
#define MVNETA_GMAC_FORCE_LINK_DOWN BIT(0)
#define MVNETA_GMAC_FORCE_LINK_PASS BIT(1)
#define MVNETA_GMAC_FORCE_LINK_UP (BIT(0) | BIT(1))
#define MVNETA_GMAC_IB_BYPASS_AN_EN BIT(3)
#define MVNETA_GMAC_CONFIG_MII_SPEED BIT(5)
#define MVNETA_GMAC_CONFIG_GMII_SPEED BIT(6)
#define MVNETA_GMAC_AN_SPEED_EN BIT(7)
#define MVNETA_GMAC_SET_FC_EN BIT(8)
#define MVNETA_GMAC_ADVERT_FC_EN BIT(9)
#define MVNETA_GMAC_CONFIG_FULL_DUPLEX BIT(12)
#define MVNETA_GMAC_AN_DUPLEX_EN BIT(13)
#define MVNETA_GMAC_SAMPLE_TX_CFG_EN BIT(15)
#define MVNETA_MIB_COUNTERS_BASE 0x3080
#define MVNETA_MIB_LATE_COLLISION 0x7c
#define MVNETA_DA_FILT_SPEC_MCAST 0x3400
#define MVNETA_DA_FILT_OTH_MCAST 0x3500
#define MVNETA_DA_FILT_UCAST_BASE 0x3600
#define MVNETA_TXQ_BASE_ADDR_REG(q) (0x3c00 + ((q) << 2))
#define MVNETA_TXQ_SIZE_REG(q) (0x3c20 + ((q) << 2))
#define MVNETA_TXQ_SENT_THRESH_ALL_MASK 0x3fff0000
#define MVNETA_TXQ_SENT_THRESH_MASK(coal) ((coal) << 16)
#define MVNETA_TXQ_UPDATE_REG(q) (0x3c60 + ((q) << 2))
#define MVNETA_TXQ_DEC_SENT_SHIFT 16
#define MVNETA_TXQ_STATUS_REG(q) (0x3c40 + ((q) << 2))
#define MVNETA_TXQ_SENT_DESC_SHIFT 16
#define MVNETA_TXQ_SENT_DESC_MASK 0x3fff0000
#define MVNETA_PORT_TX_RESET 0x3cf0
#define MVNETA_PORT_TX_DMA_RESET BIT(0)
#define MVNETA_TX_MTU 0x3e0c
#define MVNETA_TX_TOKEN_SIZE 0x3e14
#define MVNETA_TX_TOKEN_SIZE_MAX 0xffffffff
#define MVNETA_TXQ_TOKEN_SIZE_REG(q) (0x3e40 + ((q) << 2))
#define MVNETA_TXQ_TOKEN_SIZE_MAX 0x7fffffff
/* Descriptor ring Macros */
#define MVNETA_QUEUE_NEXT_DESC(q, index) \
(((index) < (q)->last_desc) ? ((index) + 1) : 0)
/* Various constants */
/* Coalescing */
#define MVNETA_TXDONE_COAL_PKTS 16
#define MVNETA_RX_COAL_PKTS 32
#define MVNETA_RX_COAL_USEC 100
/* The two bytes Marvell header. Either contains a special value used
* by Marvell switches when a specific hardware mode is enabled (not
* supported by this driver) or is filled automatically by zeroes on
* the RX side. Those two bytes being at the front of the Ethernet
* header, they allow to have the IP header aligned on a 4 bytes
* boundary automatically: the hardware skips those two bytes on its
* own.
*/
#define MVNETA_MH_SIZE 2
#define MVNETA_VLAN_TAG_LEN 4
#define MVNETA_CPU_D_CACHE_LINE_SIZE 32
#define MVNETA_TX_CSUM_MAX_SIZE 9800
#define MVNETA_ACC_MODE_EXT 1
/* Timeout constants */
#define MVNETA_TX_DISABLE_TIMEOUT_MSEC 1000
#define MVNETA_RX_DISABLE_TIMEOUT_MSEC 1000
#define MVNETA_TX_FIFO_EMPTY_TIMEOUT 10000
#define MVNETA_TX_MTU_MAX 0x3ffff
/* Max number of Rx descriptors */
#define MVNETA_MAX_RXD 16
/* Max number of Tx descriptors */
#define MVNETA_MAX_TXD 16
/* descriptor aligned size */
#define MVNETA_DESC_ALIGNED_SIZE 32
struct mvneta_port {
void __iomem *base;
struct mvneta_rx_queue *rxqs;
struct mvneta_tx_queue *txqs;
u8 mcast_count[256];
u16 tx_ring_size;
u16 rx_ring_size;
phy_interface_t phy_interface;
unsigned int link;
unsigned int duplex;
unsigned int speed;
int init;
int phyaddr;
struct phy_device *phydev;
struct mii_dev *bus;
};
/* The mvneta_tx_desc and mvneta_rx_desc structures describe the
* layout of the transmit and reception DMA descriptors, and their
* layout is therefore defined by the hardware design
*/
#define MVNETA_TX_L3_OFF_SHIFT 0
#define MVNETA_TX_IP_HLEN_SHIFT 8
#define MVNETA_TX_L4_UDP BIT(16)
#define MVNETA_TX_L3_IP6 BIT(17)
#define MVNETA_TXD_IP_CSUM BIT(18)
#define MVNETA_TXD_Z_PAD BIT(19)
#define MVNETA_TXD_L_DESC BIT(20)
#define MVNETA_TXD_F_DESC BIT(21)
#define MVNETA_TXD_FLZ_DESC (MVNETA_TXD_Z_PAD | \
MVNETA_TXD_L_DESC | \
MVNETA_TXD_F_DESC)
#define MVNETA_TX_L4_CSUM_FULL BIT(30)
#define MVNETA_TX_L4_CSUM_NOT BIT(31)
#define MVNETA_RXD_ERR_CRC 0x0
#define MVNETA_RXD_ERR_SUMMARY BIT(16)
#define MVNETA_RXD_ERR_OVERRUN BIT(17)
#define MVNETA_RXD_ERR_LEN BIT(18)
#define MVNETA_RXD_ERR_RESOURCE (BIT(17) | BIT(18))
#define MVNETA_RXD_ERR_CODE_MASK (BIT(17) | BIT(18))
#define MVNETA_RXD_L3_IP4 BIT(25)
#define MVNETA_RXD_FIRST_LAST_DESC (BIT(26) | BIT(27))
#define MVNETA_RXD_L4_CSUM_OK BIT(30)
struct mvneta_tx_desc {
u32 command; /* Options used by HW for packet transmitting.*/
u16 reserverd1; /* csum_l4 (for future use) */
u16 data_size; /* Data size of transmitted packet in bytes */
u32 buf_phys_addr; /* Physical addr of transmitted buffer */
u32 reserved2; /* hw_cmd - (for future use, PMT) */
u32 reserved3[4]; /* Reserved - (for future use) */
};
struct mvneta_rx_desc {
u32 status; /* Info about received packet */
u16 reserved1; /* pnc_info - (for future use, PnC) */
u16 data_size; /* Size of received packet in bytes */
u32 buf_phys_addr; /* Physical address of the buffer */
u32 reserved2; /* pnc_flow_id (for future use, PnC) */
u32 buf_cookie; /* cookie for access to RX buffer in rx path */
u16 reserved3; /* prefetch_cmd, for future use */
u16 reserved4; /* csum_l4 - (for future use, PnC) */
u32 reserved5; /* pnc_extra PnC (for future use, PnC) */
u32 reserved6; /* hw_cmd (for future use, PnC and HWF) */
};
struct mvneta_tx_queue {
/* Number of this TX queue, in the range 0-7 */
u8 id;
/* Number of TX DMA descriptors in the descriptor ring */
int size;
/* Index of last TX DMA descriptor that was inserted */
int txq_put_index;
/* Index of the TX DMA descriptor to be cleaned up */
int txq_get_index;
/* Virtual address of the TX DMA descriptors array */
struct mvneta_tx_desc *descs;
/* DMA address of the TX DMA descriptors array */
dma_addr_t descs_phys;
/* Index of the last TX DMA descriptor */
int last_desc;
/* Index of the next TX DMA descriptor to process */
int next_desc_to_proc;
};
struct mvneta_rx_queue {
/* rx queue number, in the range 0-7 */
u8 id;
/* num of rx descriptors in the rx descriptor ring */
int size;
/* Virtual address of the RX DMA descriptors array */
struct mvneta_rx_desc *descs;
/* DMA address of the RX DMA descriptors array */
dma_addr_t descs_phys;
/* Index of the last RX DMA descriptor */
int last_desc;
/* Index of the next RX DMA descriptor to process */
int next_desc_to_proc;
};
/* U-Boot doesn't use the queues, so set the number to 1 */
static int rxq_number = 1;
static int txq_number = 1;
static int rxq_def;
struct buffer_location {
struct mvneta_tx_desc *tx_descs;
struct mvneta_rx_desc *rx_descs;
u32 rx_buffers;
};
/*
* All 4 interfaces use the same global buffer, since only one interface
* can be enabled at once
*/
static struct buffer_location buffer_loc;
/*
* Page table entries are set to 1MB, or multiples of 1MB
* (not < 1MB). driver uses less bd's so use 1MB bdspace.
*/
#define BD_SPACE (1 << 20)
/*
* Dummy implementation that can be overwritten by a board
* specific function
*/
__weak int board_network_enable(struct mii_dev *bus)
{
return 0;
}
/* Utility/helper methods */
/* Write helper method */
static void mvreg_write(struct mvneta_port *pp, u32 offset, u32 data)
{
writel(data, pp->base + offset);
}
/* Read helper method */
static u32 mvreg_read(struct mvneta_port *pp, u32 offset)
{
return readl(pp->base + offset);
}
/* Clear all MIB counters */
static void mvneta_mib_counters_clear(struct mvneta_port *pp)
{
int i;
/* Perform dummy reads from MIB counters */
for (i = 0; i < MVNETA_MIB_LATE_COLLISION; i += 4)
mvreg_read(pp, (MVNETA_MIB_COUNTERS_BASE + i));
}
/* Rx descriptors helper methods */
/* Checks whether the RX descriptor having this status is both the first
* and the last descriptor for the RX packet. Each RX packet is currently
* received through a single RX descriptor, so not having each RX
* descriptor with its first and last bits set is an error
*/
static int mvneta_rxq_desc_is_first_last(u32 status)
{
return (status & MVNETA_RXD_FIRST_LAST_DESC) ==
MVNETA_RXD_FIRST_LAST_DESC;
}
/* Add number of descriptors ready to receive new packets */
static void mvneta_rxq_non_occup_desc_add(struct mvneta_port *pp,
struct mvneta_rx_queue *rxq,
int ndescs)
{
/* Only MVNETA_RXQ_ADD_NON_OCCUPIED_MAX (255) descriptors can
* be added at once
*/
while (ndescs > MVNETA_RXQ_ADD_NON_OCCUPIED_MAX) {
mvreg_write(pp, MVNETA_RXQ_STATUS_UPDATE_REG(rxq->id),
(MVNETA_RXQ_ADD_NON_OCCUPIED_MAX <<
MVNETA_RXQ_ADD_NON_OCCUPIED_SHIFT));
ndescs -= MVNETA_RXQ_ADD_NON_OCCUPIED_MAX;
}
mvreg_write(pp, MVNETA_RXQ_STATUS_UPDATE_REG(rxq->id),
(ndescs << MVNETA_RXQ_ADD_NON_OCCUPIED_SHIFT));
}
/* Get number of RX descriptors occupied by received packets */
static int mvneta_rxq_busy_desc_num_get(struct mvneta_port *pp,
struct mvneta_rx_queue *rxq)
{
u32 val;
val = mvreg_read(pp, MVNETA_RXQ_STATUS_REG(rxq->id));
return val & MVNETA_RXQ_OCCUPIED_ALL_MASK;
}
/* Update num of rx desc called upon return from rx path or
* from mvneta_rxq_drop_pkts().
*/
static void mvneta_rxq_desc_num_update(struct mvneta_port *pp,
struct mvneta_rx_queue *rxq,
int rx_done, int rx_filled)
{
u32 val;
if ((rx_done <= 0xff) && (rx_filled <= 0xff)) {
val = rx_done |
(rx_filled << MVNETA_RXQ_ADD_NON_OCCUPIED_SHIFT);
mvreg_write(pp, MVNETA_RXQ_STATUS_UPDATE_REG(rxq->id), val);
return;
}
/* Only 255 descriptors can be added at once */
while ((rx_done > 0) || (rx_filled > 0)) {
if (rx_done <= 0xff) {
val = rx_done;
rx_done = 0;
} else {
val = 0xff;
rx_done -= 0xff;
}
if (rx_filled <= 0xff) {
val |= rx_filled << MVNETA_RXQ_ADD_NON_OCCUPIED_SHIFT;
rx_filled = 0;
} else {
val |= 0xff << MVNETA_RXQ_ADD_NON_OCCUPIED_SHIFT;
rx_filled -= 0xff;
}
mvreg_write(pp, MVNETA_RXQ_STATUS_UPDATE_REG(rxq->id), val);
}
}
/* Get pointer to next RX descriptor to be processed by SW */
static struct mvneta_rx_desc *
mvneta_rxq_next_desc_get(struct mvneta_rx_queue *rxq)
{
int rx_desc = rxq->next_desc_to_proc;
rxq->next_desc_to_proc = MVNETA_QUEUE_NEXT_DESC(rxq, rx_desc);
return rxq->descs + rx_desc;
}
/* Tx descriptors helper methods */
/* Update HW with number of TX descriptors to be sent */
static void mvneta_txq_pend_desc_add(struct mvneta_port *pp,
struct mvneta_tx_queue *txq,
int pend_desc)
{
u32 val;
/* Only 255 descriptors can be added at once ; Assume caller
* process TX descriptors in quanta less than 256
*/
val = pend_desc;
mvreg_write(pp, MVNETA_TXQ_UPDATE_REG(txq->id), val);
}
/* Get pointer to next TX descriptor to be processed (send) by HW */
static struct mvneta_tx_desc *
mvneta_txq_next_desc_get(struct mvneta_tx_queue *txq)
{
int tx_desc = txq->next_desc_to_proc;
txq->next_desc_to_proc = MVNETA_QUEUE_NEXT_DESC(txq, tx_desc);
return txq->descs + tx_desc;
}
/* Set rxq buf size */
static void mvneta_rxq_buf_size_set(struct mvneta_port *pp,
struct mvneta_rx_queue *rxq,
int buf_size)
{
u32 val;
val = mvreg_read(pp, MVNETA_RXQ_SIZE_REG(rxq->id));
val &= ~MVNETA_RXQ_BUF_SIZE_MASK;
val |= ((buf_size >> 3) << MVNETA_RXQ_BUF_SIZE_SHIFT);
mvreg_write(pp, MVNETA_RXQ_SIZE_REG(rxq->id), val);
}
static int mvneta_port_is_fixed_link(struct mvneta_port *pp)
{
/* phy_addr is set to invalid value for fixed link */
return pp->phyaddr > PHY_MAX_ADDR;
}
/* Start the Ethernet port RX and TX activity */
static void mvneta_port_up(struct mvneta_port *pp)
{
int queue;
u32 q_map;
/* Enable all initialized TXs. */
mvneta_mib_counters_clear(pp);
q_map = 0;
for (queue = 0; queue < txq_number; queue++) {
struct mvneta_tx_queue *txq = &pp->txqs[queue];
if (txq->descs != NULL)
q_map |= (1 << queue);
}
mvreg_write(pp, MVNETA_TXQ_CMD, q_map);
/* Enable all initialized RXQs. */
q_map = 0;
for (queue = 0; queue < rxq_number; queue++) {
struct mvneta_rx_queue *rxq = &pp->rxqs[queue];
if (rxq->descs != NULL)
q_map |= (1 << queue);
}
mvreg_write(pp, MVNETA_RXQ_CMD, q_map);
}
/* Stop the Ethernet port activity */
static void mvneta_port_down(struct mvneta_port *pp)
{
u32 val;
int count;
/* Stop Rx port activity. Check port Rx activity. */
val = mvreg_read(pp, MVNETA_RXQ_CMD) & MVNETA_RXQ_ENABLE_MASK;
/* Issue stop command for active channels only */
if (val != 0)
mvreg_write(pp, MVNETA_RXQ_CMD,
val << MVNETA_RXQ_DISABLE_SHIFT);
/* Wait for all Rx activity to terminate. */
count = 0;
do {
if (count++ >= MVNETA_RX_DISABLE_TIMEOUT_MSEC) {
netdev_warn(pp->dev,
"TIMEOUT for RX stopped ! rx_queue_cmd: 0x08%x\n",
val);
break;
}
mdelay(1);
val = mvreg_read(pp, MVNETA_RXQ_CMD);
} while (val & 0xff);
/* Stop Tx port activity. Check port Tx activity. Issue stop
* command for active channels only
*/
val = (mvreg_read(pp, MVNETA_TXQ_CMD)) & MVNETA_TXQ_ENABLE_MASK;
if (val != 0)
mvreg_write(pp, MVNETA_TXQ_CMD,
(val << MVNETA_TXQ_DISABLE_SHIFT));
/* Wait for all Tx activity to terminate. */
count = 0;
do {
if (count++ >= MVNETA_TX_DISABLE_TIMEOUT_MSEC) {
netdev_warn(pp->dev,
"TIMEOUT for TX stopped status=0x%08x\n",
val);
break;
}
mdelay(1);
/* Check TX Command reg that all Txqs are stopped */
val = mvreg_read(pp, MVNETA_TXQ_CMD);
} while (val & 0xff);
/* Double check to verify that TX FIFO is empty */
count = 0;
do {
if (count++ >= MVNETA_TX_FIFO_EMPTY_TIMEOUT) {
netdev_warn(pp->dev,
"TX FIFO empty timeout status=0x08%x\n",
val);
break;
}
mdelay(1);
val = mvreg_read(pp, MVNETA_PORT_STATUS);
} while (!(val & MVNETA_TX_FIFO_EMPTY) &&
(val & MVNETA_TX_IN_PRGRS));
udelay(200);
}
/* Enable the port by setting the port enable bit of the MAC control register */
static void mvneta_port_enable(struct mvneta_port *pp)
{
u32 val;
/* Enable port */
val = mvreg_read(pp, MVNETA_GMAC_CTRL_0);
val |= MVNETA_GMAC0_PORT_ENABLE;
mvreg_write(pp, MVNETA_GMAC_CTRL_0, val);
}
/* Disable the port and wait for about 200 usec before retuning */
static void mvneta_port_disable(struct mvneta_port *pp)
{
u32 val;
/* Reset the Enable bit in the Serial Control Register */
val = mvreg_read(pp, MVNETA_GMAC_CTRL_0);
val &= ~MVNETA_GMAC0_PORT_ENABLE;
mvreg_write(pp, MVNETA_GMAC_CTRL_0, val);
udelay(200);
}
/* Multicast tables methods */
/* Set all entries in Unicast MAC Table; queue==-1 means reject all */
static void mvneta_set_ucast_table(struct mvneta_port *pp, int queue)
{
int offset;
u32 val;
if (queue == -1) {
val = 0;
} else {
val = 0x1 | (queue << 1);
val |= (val << 24) | (val << 16) | (val << 8);
}
for (offset = 0; offset <= 0xc; offset += 4)
mvreg_write(pp, MVNETA_DA_FILT_UCAST_BASE + offset, val);
}
/* Set all entries in Special Multicast MAC Table; queue==-1 means reject all */
static void mvneta_set_special_mcast_table(struct mvneta_port *pp, int queue)
{
int offset;
u32 val;
if (queue == -1) {
val = 0;
} else {
val = 0x1 | (queue << 1);
val |= (val << 24) | (val << 16) | (val << 8);
}
for (offset = 0; offset <= 0xfc; offset += 4)
mvreg_write(pp, MVNETA_DA_FILT_SPEC_MCAST + offset, val);
}
/* Set all entries in Other Multicast MAC Table. queue==-1 means reject all */
static void mvneta_set_other_mcast_table(struct mvneta_port *pp, int queue)
{
int offset;
u32 val;
if (queue == -1) {
memset(pp->mcast_count, 0, sizeof(pp->mcast_count));
val = 0;
} else {
memset(pp->mcast_count, 1, sizeof(pp->mcast_count));
val = 0x1 | (queue << 1);
val |= (val << 24) | (val << 16) | (val << 8);
}
for (offset = 0; offset <= 0xfc; offset += 4)
mvreg_write(pp, MVNETA_DA_FILT_OTH_MCAST + offset, val);
}
/* This method sets defaults to the NETA port:
* Clears interrupt Cause and Mask registers.
* Clears all MAC tables.
* Sets defaults to all registers.
* Resets RX and TX descriptor rings.
* Resets PHY.
* This method can be called after mvneta_port_down() to return the port
* settings to defaults.
*/
static void mvneta_defaults_set(struct mvneta_port *pp)
{
int cpu;
int queue;
u32 val;
/* Clear all Cause registers */
mvreg_write(pp, MVNETA_INTR_NEW_CAUSE, 0);
mvreg_write(pp, MVNETA_INTR_OLD_CAUSE, 0);
mvreg_write(pp, MVNETA_INTR_MISC_CAUSE, 0);
/* Mask all interrupts */
mvreg_write(pp, MVNETA_INTR_NEW_MASK, 0);
mvreg_write(pp, MVNETA_INTR_OLD_MASK, 0);
mvreg_write(pp, MVNETA_INTR_MISC_MASK, 0);
mvreg_write(pp, MVNETA_INTR_ENABLE, 0);
/* Enable MBUS Retry bit16 */
mvreg_write(pp, MVNETA_MBUS_RETRY, 0x20);
/* Set CPU queue access map - all CPUs have access to all RX
* queues and to all TX queues
*/
for (cpu = 0; cpu < CONFIG_NR_CPUS; cpu++)
mvreg_write(pp, MVNETA_CPU_MAP(cpu),
(MVNETA_CPU_RXQ_ACCESS_ALL_MASK |
MVNETA_CPU_TXQ_ACCESS_ALL_MASK));
/* Reset RX and TX DMAs */
mvreg_write(pp, MVNETA_PORT_RX_RESET, MVNETA_PORT_RX_DMA_RESET);
mvreg_write(pp, MVNETA_PORT_TX_RESET, MVNETA_PORT_TX_DMA_RESET);
/* Disable Legacy WRR, Disable EJP, Release from reset */
mvreg_write(pp, MVNETA_TXQ_CMD_1, 0);
for (queue = 0; queue < txq_number; queue++) {
mvreg_write(pp, MVETH_TXQ_TOKEN_COUNT_REG(queue), 0);
mvreg_write(pp, MVETH_TXQ_TOKEN_CFG_REG(queue), 0);
}
mvreg_write(pp, MVNETA_PORT_TX_RESET, 0);
mvreg_write(pp, MVNETA_PORT_RX_RESET, 0);
/* Set Port Acceleration Mode */
val = MVNETA_ACC_MODE_EXT;
mvreg_write(pp, MVNETA_ACC_MODE, val);
/* Update val of portCfg register accordingly with all RxQueue types */
val = MVNETA_PORT_CONFIG_DEFL_VALUE(rxq_def);
mvreg_write(pp, MVNETA_PORT_CONFIG, val);
val = 0;
mvreg_write(pp, MVNETA_PORT_CONFIG_EXTEND, val);
mvreg_write(pp, MVNETA_RX_MIN_FRAME_SIZE, 64);
/* Build PORT_SDMA_CONFIG_REG */
val = 0;
/* Default burst size */
val |= MVNETA_TX_BRST_SZ_MASK(MVNETA_SDMA_BRST_SIZE_16);
val |= MVNETA_RX_BRST_SZ_MASK(MVNETA_SDMA_BRST_SIZE_16);
val |= MVNETA_RX_NO_DATA_SWAP | MVNETA_TX_NO_DATA_SWAP;
/* Assign port SDMA configuration */
mvreg_write(pp, MVNETA_SDMA_CONFIG, val);
/* Enable PHY polling in hardware if not in fixed-link mode */
if (!mvneta_port_is_fixed_link(pp)) {
val = mvreg_read(pp, MVNETA_UNIT_CONTROL);
val |= MVNETA_PHY_POLLING_ENABLE;
mvreg_write(pp, MVNETA_UNIT_CONTROL, val);
}
mvneta_set_ucast_table(pp, -1);
mvneta_set_special_mcast_table(pp, -1);
mvneta_set_other_mcast_table(pp, -1);
}
/* Set unicast address */
static void mvneta_set_ucast_addr(struct mvneta_port *pp, u8 last_nibble,
int queue)
{
unsigned int unicast_reg;
unsigned int tbl_offset;
unsigned int reg_offset;
/* Locate the Unicast table entry */
last_nibble = (0xf & last_nibble);
/* offset from unicast tbl base */
tbl_offset = (last_nibble / 4) * 4;
/* offset within the above reg */
reg_offset = last_nibble % 4;
unicast_reg = mvreg_read(pp, (MVNETA_DA_FILT_UCAST_BASE + tbl_offset));
if (queue == -1) {
/* Clear accepts frame bit at specified unicast DA tbl entry */
unicast_reg &= ~(0xff << (8 * reg_offset));
} else {
unicast_reg &= ~(0xff << (8 * reg_offset));
unicast_reg |= ((0x01 | (queue << 1)) << (8 * reg_offset));
}
mvreg_write(pp, (MVNETA_DA_FILT_UCAST_BASE + tbl_offset), unicast_reg);
}
/* Set mac address */
static void mvneta_mac_addr_set(struct mvneta_port *pp, unsigned char *addr,
int queue)
{
unsigned int mac_h;
unsigned int mac_l;
if (queue != -1) {
mac_l = (addr[4] << 8) | (addr[5]);
mac_h = (addr[0] << 24) | (addr[1] << 16) |
(addr[2] << 8) | (addr[3] << 0);
mvreg_write(pp, MVNETA_MAC_ADDR_LOW, mac_l);
mvreg_write(pp, MVNETA_MAC_ADDR_HIGH, mac_h);
}
/* Accept frames of this address */
mvneta_set_ucast_addr(pp, addr[5], queue);
}
static int mvneta_write_hwaddr(struct udevice *dev)
{
mvneta_mac_addr_set(dev_get_priv(dev),
((struct eth_pdata *)dev_get_platdata(dev))->enetaddr,
rxq_def);
return 0;
}
/* Handle rx descriptor fill by setting buf_cookie and buf_phys_addr */
static void mvneta_rx_desc_fill(struct mvneta_rx_desc *rx_desc,
u32 phys_addr, u32 cookie)
{
rx_desc->buf_cookie = cookie;
rx_desc->buf_phys_addr = phys_addr;
}
/* Decrement sent descriptors counter */
static void mvneta_txq_sent_desc_dec(struct mvneta_port *pp,
struct mvneta_tx_queue *txq,
int sent_desc)
{
u32 val;
/* Only 255 TX descriptors can be updated at once */
while (sent_desc > 0xff) {
val = 0xff << MVNETA_TXQ_DEC_SENT_SHIFT;
mvreg_write(pp, MVNETA_TXQ_UPDATE_REG(txq->id), val);
sent_desc = sent_desc - 0xff;
}
val = sent_desc << MVNETA_TXQ_DEC_SENT_SHIFT;
mvreg_write(pp, MVNETA_TXQ_UPDATE_REG(txq->id), val);
}
/* Get number of TX descriptors already sent by HW */
static int mvneta_txq_sent_desc_num_get(struct mvneta_port *pp,
struct mvneta_tx_queue *txq)
{
u32 val;
int sent_desc;
val = mvreg_read(pp, MVNETA_TXQ_STATUS_REG(txq->id));
sent_desc = (val & MVNETA_TXQ_SENT_DESC_MASK) >>
MVNETA_TXQ_SENT_DESC_SHIFT;
return sent_desc;
}
/* Display more error info */
static void mvneta_rx_error(struct mvneta_port *pp,
struct mvneta_rx_desc *rx_desc)
{
u32 status = rx_desc->status;
if (!mvneta_rxq_desc_is_first_last(status)) {
netdev_err(pp->dev,
"bad rx status %08x (buffer oversize), size=%d\n",
status, rx_desc->data_size);
return;
}
switch (status & MVNETA_RXD_ERR_CODE_MASK) {
case MVNETA_RXD_ERR_CRC:
netdev_err(pp->dev, "bad rx status %08x (crc error), size=%d\n",
status, rx_desc->data_size);
break;
case MVNETA_RXD_ERR_OVERRUN:
netdev_err(pp->dev, "bad rx status %08x (overrun error), size=%d\n",
status, rx_desc->data_size);
break;
case MVNETA_RXD_ERR_LEN:
netdev_err(pp->dev, "bad rx status %08x (max frame length error), size=%d\n",
status, rx_desc->data_size);
break;
case MVNETA_RXD_ERR_RESOURCE:
netdev_err(pp->dev, "bad rx status %08x (resource error), size=%d\n",
status, rx_desc->data_size);
break;
}
}
static struct mvneta_rx_queue *mvneta_rxq_handle_get(struct mvneta_port *pp,
int rxq)
{
return &pp->rxqs[rxq];
}
/* Drop packets received by the RXQ and free buffers */
static void mvneta_rxq_drop_pkts(struct mvneta_port *pp,
struct mvneta_rx_queue *rxq)
{
int rx_done;
rx_done = mvneta_rxq_busy_desc_num_get(pp, rxq);
if (rx_done)
mvneta_rxq_desc_num_update(pp, rxq, rx_done, rx_done);
}
/* Handle rxq fill: allocates rxq skbs; called when initializing a port */
static int mvneta_rxq_fill(struct mvneta_port *pp, struct mvneta_rx_queue *rxq,
int num)
{
int i;
for (i = 0; i < num; i++) {
u32 addr;
/* U-Boot special: Fill in the rx buffer addresses */
addr = buffer_loc.rx_buffers + (i * RX_BUFFER_SIZE);
mvneta_rx_desc_fill(rxq->descs + i, addr, addr);
}
/* Add this number of RX descriptors as non occupied (ready to
* get packets)
*/
mvneta_rxq_non_occup_desc_add(pp, rxq, i);
return 0;
}
/* Rx/Tx queue initialization/cleanup methods */
/* Create a specified RX queue */
static int mvneta_rxq_init(struct mvneta_port *pp,
struct mvneta_rx_queue *rxq)
{
rxq->size = pp->rx_ring_size;
/* Allocate memory for RX descriptors */
rxq->descs_phys = (dma_addr_t)rxq->descs;
if (rxq->descs == NULL)
return -ENOMEM;
rxq->last_desc = rxq->size - 1;
/* Set Rx descriptors queue starting address */
mvreg_write(pp, MVNETA_RXQ_BASE_ADDR_REG(rxq->id), rxq->descs_phys);
mvreg_write(pp, MVNETA_RXQ_SIZE_REG(rxq->id), rxq->size);
/* Fill RXQ with buffers from RX pool */
mvneta_rxq_buf_size_set(pp, rxq, RX_BUFFER_SIZE);
mvneta_rxq_fill(pp, rxq, rxq->size);
return 0;
}
/* Cleanup Rx queue */
static void mvneta_rxq_deinit(struct mvneta_port *pp,
struct mvneta_rx_queue *rxq)
{
mvneta_rxq_drop_pkts(pp, rxq);
rxq->descs = NULL;
rxq->last_desc = 0;
rxq->next_desc_to_proc = 0;
rxq->descs_phys = 0;
}
/* Create and initialize a tx queue */
static int mvneta_txq_init(struct mvneta_port *pp,
struct mvneta_tx_queue *txq)
{
txq->size = pp->tx_ring_size;
/* Allocate memory for TX descriptors */
txq->descs_phys = (dma_addr_t)txq->descs;
if (txq->descs == NULL)
return -ENOMEM;
txq->last_desc = txq->size - 1;
/* Set maximum bandwidth for enabled TXQs */
mvreg_write(pp, MVETH_TXQ_TOKEN_CFG_REG(txq->id), 0x03ffffff);
mvreg_write(pp, MVETH_TXQ_TOKEN_COUNT_REG(txq->id), 0x3fffffff);
/* Set Tx descriptors queue starting address */
mvreg_write(pp, MVNETA_TXQ_BASE_ADDR_REG(txq->id), txq->descs_phys);
mvreg_write(pp, MVNETA_TXQ_SIZE_REG(txq->id), txq->size);
return 0;
}
/* Free allocated resources when mvneta_txq_init() fails to allocate memory*/
static void mvneta_txq_deinit(struct mvneta_port *pp,
struct mvneta_tx_queue *txq)
{
txq->descs = NULL;
txq->last_desc = 0;
txq->next_desc_to_proc = 0;
txq->descs_phys = 0;
/* Set minimum bandwidth for disabled TXQs */
mvreg_write(pp, MVETH_TXQ_TOKEN_CFG_REG(txq->id), 0);
mvreg_write(pp, MVETH_TXQ_TOKEN_COUNT_REG(txq->id), 0);
/* Set Tx descriptors queue starting address and size */
mvreg_write(pp, MVNETA_TXQ_BASE_ADDR_REG(txq->id), 0);
mvreg_write(pp, MVNETA_TXQ_SIZE_REG(txq->id), 0);
}
/* Cleanup all Tx queues */
static void mvneta_cleanup_txqs(struct mvneta_port *pp)
{
int queue;
for (queue = 0; queue < txq_number; queue++)
mvneta_txq_deinit(pp, &pp->txqs[queue]);
}
/* Cleanup all Rx queues */
static void mvneta_cleanup_rxqs(struct mvneta_port *pp)
{
int queue;
for (queue = 0; queue < rxq_number; queue++)
mvneta_rxq_deinit(pp, &pp->rxqs[queue]);
}
/* Init all Rx queues */
static int mvneta_setup_rxqs(struct mvneta_port *pp)
{
int queue;
for (queue = 0; queue < rxq_number; queue++) {
int err = mvneta_rxq_init(pp, &pp->rxqs[queue]);
if (err) {
netdev_err(pp->dev, "%s: can't create rxq=%d\n",
__func__, queue);
mvneta_cleanup_rxqs(pp);
return err;
}
}
return 0;
}
/* Init all tx queues */
static int mvneta_setup_txqs(struct mvneta_port *pp)
{
int queue;
for (queue = 0; queue < txq_number; queue++) {
int err = mvneta_txq_init(pp, &pp->txqs[queue]);
if (err) {
netdev_err(pp->dev, "%s: can't create txq=%d\n",
__func__, queue);
mvneta_cleanup_txqs(pp);
return err;
}
}
return 0;
}
static void mvneta_start_dev(struct mvneta_port *pp)
{
/* start the Rx/Tx activity */
mvneta_port_enable(pp);
}
static void mvneta_adjust_link(struct udevice *dev)
{
struct mvneta_port *pp = dev_get_priv(dev);
struct phy_device *phydev = pp->phydev;
int status_change = 0;
if (mvneta_port_is_fixed_link(pp)) {
debug("Using fixed link, skip link adjust\n");
return;
}
if (phydev->link) {
if ((pp->speed != phydev->speed) ||
(pp->duplex != phydev->duplex)) {
u32 val;
val = mvreg_read(pp, MVNETA_GMAC_AUTONEG_CONFIG);
val &= ~(MVNETA_GMAC_CONFIG_MII_SPEED |
MVNETA_GMAC_CONFIG_GMII_SPEED |
MVNETA_GMAC_CONFIG_FULL_DUPLEX |
MVNETA_GMAC_AN_SPEED_EN |
MVNETA_GMAC_AN_DUPLEX_EN);
if (phydev->duplex)
val |= MVNETA_GMAC_CONFIG_FULL_DUPLEX;
if (phydev->speed == SPEED_1000)
val |= MVNETA_GMAC_CONFIG_GMII_SPEED;
else
val |= MVNETA_GMAC_CONFIG_MII_SPEED;
mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val);
pp->duplex = phydev->duplex;
pp->speed = phydev->speed;
}
}
if (phydev->link != pp->link) {
if (!phydev->link) {
pp->duplex = -1;
pp->speed = 0;
}
pp->link = phydev->link;
status_change = 1;
}
if (status_change) {
if (phydev->link) {
u32 val = mvreg_read(pp, MVNETA_GMAC_AUTONEG_CONFIG);
val |= (MVNETA_GMAC_FORCE_LINK_PASS |
MVNETA_GMAC_FORCE_LINK_DOWN);
mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val);
mvneta_port_up(pp);
} else {
mvneta_port_down(pp);
}
}
}
static int mvneta_open(struct udevice *dev)
{
struct mvneta_port *pp = dev_get_priv(dev);
int ret;
ret = mvneta_setup_rxqs(pp);
if (ret)
return ret;
ret = mvneta_setup_txqs(pp);
if (ret)
return ret;
mvneta_adjust_link(dev);
mvneta_start_dev(pp);
return 0;
}
/* Initialize hw */
static int mvneta_init2(struct mvneta_port *pp)
{
int queue;
/* Disable port */
mvneta_port_disable(pp);
/* Set port default values */
mvneta_defaults_set(pp);
pp->txqs = kzalloc(txq_number * sizeof(struct mvneta_tx_queue),
GFP_KERNEL);
if (!pp->txqs)
return -ENOMEM;
/* U-Boot special: use preallocated area */
pp->txqs[0].descs = buffer_loc.tx_descs;
/* Initialize TX descriptor rings */
for (queue = 0; queue < txq_number; queue++) {
struct mvneta_tx_queue *txq = &pp->txqs[queue];
txq->id = queue;
txq->size = pp->tx_ring_size;
}
pp->rxqs = kzalloc(rxq_number * sizeof(struct mvneta_rx_queue),
GFP_KERNEL);
if (!pp->rxqs) {
kfree(pp->txqs);
return -ENOMEM;
}
/* U-Boot special: use preallocated area */
pp->rxqs[0].descs = buffer_loc.rx_descs;
/* Create Rx descriptor rings */
for (queue = 0; queue < rxq_number; queue++) {
struct mvneta_rx_queue *rxq = &pp->rxqs[queue];
rxq->id = queue;
rxq->size = pp->rx_ring_size;
}
return 0;
}
/* platform glue : initialize decoding windows */
/*
* Not like A380, in Armada3700, there are two layers of decode windows for GBE:
* First layer is: GbE Address window that resides inside the GBE unit,
* Second layer is: Fabric address window which is located in the NIC400
* (South Fabric).
* To simplify the address decode configuration for Armada3700, we bypass the
* first layer of GBE decode window by setting the first window to 4GB.
*/
static void mvneta_bypass_mbus_windows(struct mvneta_port *pp)
{
/*
* Set window size to 4GB, to bypass GBE address decode, leave the
* work to MBUS decode window
*/
mvreg_write(pp, MVNETA_WIN_SIZE(0), MVNETA_WIN_SIZE_MASK);
/* Enable GBE address decode window 0 by set bit 0 to 0 */
clrbits_le32(pp->base + MVNETA_BASE_ADDR_ENABLE,
MVNETA_BASE_ADDR_ENABLE_BIT);
/* Set GBE address decode window 0 to full Access (read or write) */
setbits_le32(pp->base + MVNETA_PORT_ACCESS_PROTECT,
MVNETA_PORT_ACCESS_PROTECT_WIN0_RW);
}
static void mvneta_conf_mbus_windows(struct mvneta_port *pp)
{
const struct mbus_dram_target_info *dram;
u32 win_enable;
u32 win_protect;
int i;
dram = mvebu_mbus_dram_info();
for (i = 0; i < 6; i++) {
mvreg_write(pp, MVNETA_WIN_BASE(i), 0);
mvreg_write(pp, MVNETA_WIN_SIZE(i), 0);
if (i < 4)
mvreg_write(pp, MVNETA_WIN_REMAP(i), 0);
}
win_enable = 0x3f;
win_protect = 0;
for (i = 0; i < dram->num_cs; i++) {
const struct mbus_dram_window *cs = dram->cs + i;
mvreg_write(pp, MVNETA_WIN_BASE(i), (cs->base & 0xffff0000) |
(cs->mbus_attr << 8) | dram->mbus_dram_target_id);
mvreg_write(pp, MVNETA_WIN_SIZE(i),
(cs->size - 1) & 0xffff0000);
win_enable &= ~(1 << i);
win_protect |= 3 << (2 * i);
}
mvreg_write(pp, MVNETA_BASE_ADDR_ENABLE, win_enable);
}
/* Power up the port */
static int mvneta_port_power_up(struct mvneta_port *pp, int phy_mode)
{
u32 ctrl;
/* MAC Cause register should be cleared */
mvreg_write(pp, MVNETA_UNIT_INTR_CAUSE, 0);
ctrl = mvreg_read(pp, MVNETA_GMAC_CTRL_2);
/* Even though it might look weird, when we're configured in
* SGMII or QSGMII mode, the RGMII bit needs to be set.
*/
switch (phy_mode) {
case PHY_INTERFACE_MODE_QSGMII:
mvreg_write(pp, MVNETA_SERDES_CFG, MVNETA_QSGMII_SERDES_PROTO);
ctrl |= MVNETA_GMAC2_PCS_ENABLE | MVNETA_GMAC2_PORT_RGMII;
break;
case PHY_INTERFACE_MODE_SGMII:
mvreg_write(pp, MVNETA_SERDES_CFG, MVNETA_SGMII_SERDES_PROTO);
ctrl |= MVNETA_GMAC2_PCS_ENABLE | MVNETA_GMAC2_PORT_RGMII;
break;
case PHY_INTERFACE_MODE_RGMII:
case PHY_INTERFACE_MODE_RGMII_ID:
ctrl |= MVNETA_GMAC2_PORT_RGMII;
break;
default:
return -EINVAL;
}
/* Cancel Port Reset */
ctrl &= ~MVNETA_GMAC2_PORT_RESET;
mvreg_write(pp, MVNETA_GMAC_CTRL_2, ctrl);
while ((mvreg_read(pp, MVNETA_GMAC_CTRL_2) &
MVNETA_GMAC2_PORT_RESET) != 0)
continue;
return 0;
}
/* Device initialization routine */
static int mvneta_init(struct udevice *dev)
{
struct eth_pdata *pdata = dev_get_platdata(dev);
struct mvneta_port *pp = dev_get_priv(dev);
int err;
pp->tx_ring_size = MVNETA_MAX_TXD;
pp->rx_ring_size = MVNETA_MAX_RXD;
err = mvneta_init2(pp);
if (err < 0) {
dev_err(&pdev->dev, "can't init eth hal\n");
return err;
}
mvneta_mac_addr_set(pp, pdata->enetaddr, rxq_def);
err = mvneta_port_power_up(pp, pp->phy_interface);
if (err < 0) {
dev_err(&pdev->dev, "can't power up port\n");
return err;
}
/* Call open() now as it needs to be done before runing send() */
mvneta_open(dev);
return 0;
}
/* U-Boot only functions follow here */
/* SMI / MDIO functions */
static int smi_wait_ready(struct mvneta_port *pp)
{
u32 timeout = MVNETA_SMI_TIMEOUT;
u32 smi_reg;
/* wait till the SMI is not busy */
do {
/* read smi register */
smi_reg = mvreg_read(pp, MVNETA_SMI);
if (timeout-- == 0) {
printf("Error: SMI busy timeout\n");
return -EFAULT;
}
} while (smi_reg & MVNETA_SMI_BUSY);
return 0;
}
/*
* mvneta_mdio_read - miiphy_read callback function.
*
* Returns 16bit phy register value, or 0xffff on error
*/
static int mvneta_mdio_read(struct mii_dev *bus, int addr, int devad, int reg)
{
struct mvneta_port *pp = bus->priv;
u32 smi_reg;
u32 timeout;
/* check parameters */
if (addr > MVNETA_PHY_ADDR_MASK) {
printf("Error: Invalid PHY address %d\n", addr);
return -EFAULT;
}
if (reg > MVNETA_PHY_REG_MASK) {
printf("Err: Invalid register offset %d\n", reg);
return -EFAULT;
}
/* wait till the SMI is not busy */
if (smi_wait_ready(pp) < 0)
return -EFAULT;
/* fill the phy address and regiser offset and read opcode */
smi_reg = (addr << MVNETA_SMI_DEV_ADDR_OFFS)
| (reg << MVNETA_SMI_REG_ADDR_OFFS)
| MVNETA_SMI_OPCODE_READ;
/* write the smi register */
mvreg_write(pp, MVNETA_SMI, smi_reg);
/* wait till read value is ready */
timeout = MVNETA_SMI_TIMEOUT;
do {
/* read smi register */
smi_reg = mvreg_read(pp, MVNETA_SMI);
if (timeout-- == 0) {
printf("Err: SMI read ready timeout\n");
return -EFAULT;
}
} while (!(smi_reg & MVNETA_SMI_READ_VALID));
/* Wait for the data to update in the SMI register */
for (timeout = 0; timeout < MVNETA_SMI_TIMEOUT; timeout++)
;
return mvreg_read(pp, MVNETA_SMI) & MVNETA_SMI_DATA_MASK;
}
/*
* mvneta_mdio_write - miiphy_write callback function.
*
* Returns 0 if write succeed, -EINVAL on bad parameters
* -ETIME on timeout
*/
static int mvneta_mdio_write(struct mii_dev *bus, int addr, int devad, int reg,
u16 value)
{
struct mvneta_port *pp = bus->priv;
u32 smi_reg;
/* check parameters */
if (addr > MVNETA_PHY_ADDR_MASK) {
printf("Error: Invalid PHY address %d\n", addr);
return -EFAULT;
}
if (reg > MVNETA_PHY_REG_MASK) {
printf("Err: Invalid register offset %d\n", reg);
return -EFAULT;
}
/* wait till the SMI is not busy */
if (smi_wait_ready(pp) < 0)
return -EFAULT;
/* fill the phy addr and reg offset and write opcode and data */
smi_reg = value << MVNETA_SMI_DATA_OFFS;
smi_reg |= (addr << MVNETA_SMI_DEV_ADDR_OFFS)
| (reg << MVNETA_SMI_REG_ADDR_OFFS);
smi_reg &= ~MVNETA_SMI_OPCODE_READ;
/* write the smi register */
mvreg_write(pp, MVNETA_SMI, smi_reg);
return 0;
}
static int mvneta_start(struct udevice *dev)
{
struct mvneta_port *pp = dev_get_priv(dev);
struct phy_device *phydev;
mvneta_port_power_up(pp, pp->phy_interface);
if (!pp->init || pp->link == 0) {
if (mvneta_port_is_fixed_link(pp)) {
u32 val;
pp->init = 1;
pp->link = 1;
mvneta_init(dev);
val = MVNETA_GMAC_FORCE_LINK_UP |
MVNETA_GMAC_IB_BYPASS_AN_EN |
MVNETA_GMAC_SET_FC_EN |
MVNETA_GMAC_ADVERT_FC_EN |
MVNETA_GMAC_SAMPLE_TX_CFG_EN;
if (pp->duplex)
val |= MVNETA_GMAC_CONFIG_FULL_DUPLEX;
if (pp->speed == SPEED_1000)
val |= MVNETA_GMAC_CONFIG_GMII_SPEED;
else if (pp->speed == SPEED_100)
val |= MVNETA_GMAC_CONFIG_MII_SPEED;
mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val);
} else {
/* Set phy address of the port */
mvreg_write(pp, MVNETA_PHY_ADDR, pp->phyaddr);
phydev = phy_connect(pp->bus, pp->phyaddr, dev,
pp->phy_interface);
pp->phydev = phydev;
phy_config(phydev);
phy_startup(phydev);
if (!phydev->link) {
printf("%s: No link.\n", phydev->dev->name);
return -1;
}
/* Full init on first call */
mvneta_init(dev);
pp->init = 1;
return 0;
}
}
/* Upon all following calls, this is enough */
mvneta_port_up(pp);
mvneta_port_enable(pp);
return 0;
}
static int mvneta_send(struct udevice *dev, void *packet, int length)
{
struct mvneta_port *pp = dev_get_priv(dev);
struct mvneta_tx_queue *txq = &pp->txqs[0];
struct mvneta_tx_desc *tx_desc;
int sent_desc;
u32 timeout = 0;
/* Get a descriptor for the first part of the packet */
tx_desc = mvneta_txq_next_desc_get(txq);
tx_desc->buf_phys_addr = (u32)(uintptr_t)packet;
tx_desc->data_size = length;
flush_dcache_range((ulong)packet,
(ulong)packet + ALIGN(length, PKTALIGN));
/* First and Last descriptor */
tx_desc->command = MVNETA_TX_L4_CSUM_NOT | MVNETA_TXD_FLZ_DESC;
mvneta_txq_pend_desc_add(pp, txq, 1);
/* Wait for packet to be sent (queue might help with speed here) */
sent_desc = mvneta_txq_sent_desc_num_get(pp, txq);
while (!sent_desc) {
if (timeout++ > 10000) {
printf("timeout: packet not sent\n");
return -1;
}
sent_desc = mvneta_txq_sent_desc_num_get(pp, txq);
}
/* txDone has increased - hw sent packet */
mvneta_txq_sent_desc_dec(pp, txq, sent_desc);
return 0;
}
static int mvneta_recv(struct udevice *dev, int flags, uchar **packetp)
{
struct mvneta_port *pp = dev_get_priv(dev);
int rx_done;
struct mvneta_rx_queue *rxq;
int rx_bytes = 0;
/* get rx queue */
rxq = mvneta_rxq_handle_get(pp, rxq_def);
rx_done = mvneta_rxq_busy_desc_num_get(pp, rxq);
if (rx_done) {
struct mvneta_rx_desc *rx_desc;
unsigned char *data;
u32 rx_status;
/*
* No cache invalidation needed here, since the desc's are
* located in a uncached memory region
*/
rx_desc = mvneta_rxq_next_desc_get(rxq);
rx_status = rx_desc->status;
if (!mvneta_rxq_desc_is_first_last(rx_status) ||
(rx_status & MVNETA_RXD_ERR_SUMMARY)) {
mvneta_rx_error(pp, rx_desc);
/* leave the descriptor untouched */
return -EIO;
}
/* 2 bytes for marvell header. 4 bytes for crc */
rx_bytes = rx_desc->data_size - 6;
/* give packet to stack - skip on first 2 bytes */
data = (u8 *)(uintptr_t)rx_desc->buf_cookie + 2;
/*
* No cache invalidation needed here, since the rx_buffer's are
* located in a uncached memory region
*/
*packetp = data;
/*
* Only mark one descriptor as free
* since only one was processed
*/
mvneta_rxq_desc_num_update(pp, rxq, 1, 1);
}
return rx_bytes;
}
static int mvneta_probe(struct udevice *dev)
{
struct eth_pdata *pdata = dev_get_platdata(dev);
struct mvneta_port *pp = dev_get_priv(dev);
void *blob = (void *)gd->fdt_blob;
int node = dev_of_offset(dev);
struct mii_dev *bus;
unsigned long addr;
void *bd_space;
int ret;
int fl_node;
/*
* Allocate buffer area for descs and rx_buffers. This is only
* done once for all interfaces. As only one interface can
* be active. Make this area DMA safe by disabling the D-cache
*/
if (!buffer_loc.tx_descs) {
/* Align buffer area for descs and rx_buffers to 1MiB */
bd_space = memalign(1 << MMU_SECTION_SHIFT, BD_SPACE);
mmu_set_region_dcache_behaviour((phys_addr_t)bd_space, BD_SPACE,
DCACHE_OFF);
buffer_loc.tx_descs = (struct mvneta_tx_desc *)bd_space;
buffer_loc.rx_descs = (struct mvneta_rx_desc *)
((phys_addr_t)bd_space +
MVNETA_MAX_TXD * sizeof(struct mvneta_tx_desc));
buffer_loc.rx_buffers = (phys_addr_t)
(bd_space +
MVNETA_MAX_TXD * sizeof(struct mvneta_tx_desc) +
MVNETA_MAX_RXD * sizeof(struct mvneta_rx_desc));
}
pp->base = (void __iomem *)pdata->iobase;
/* Configure MBUS address windows */
if (device_is_compatible(dev, "marvell,armada-3700-neta"))
mvneta_bypass_mbus_windows(pp);
else
mvneta_conf_mbus_windows(pp);
/* PHY interface is already decoded in mvneta_ofdata_to_platdata() */
pp->phy_interface = pdata->phy_interface;
/* fetch 'fixed-link' property from 'neta' node */
fl_node = fdt_subnode_offset(blob, node, "fixed-link");
if (fl_node != -FDT_ERR_NOTFOUND) {
/* set phy_addr to invalid value for fixed link */
pp->phyaddr = PHY_MAX_ADDR + 1;
pp->duplex = fdtdec_get_bool(blob, fl_node, "full-duplex");
pp->speed = fdtdec_get_int(blob, fl_node, "speed", 0);
} else {
/* Now read phyaddr from DT */
addr = fdtdec_get_int(blob, node, "phy", 0);
addr = fdt_node_offset_by_phandle(blob, addr);
pp->phyaddr = fdtdec_get_int(blob, addr, "reg", 0);
}
bus = mdio_alloc();
if (!bus) {
printf("Failed to allocate MDIO bus\n");
return -ENOMEM;
}
bus->read = mvneta_mdio_read;
bus->write = mvneta_mdio_write;
snprintf(bus->name, sizeof(bus->name), dev->name);
bus->priv = (void *)pp;
pp->bus = bus;
ret = mdio_register(bus);
if (ret)
return ret;
return board_network_enable(bus);
}
static void mvneta_stop(struct udevice *dev)
{
struct mvneta_port *pp = dev_get_priv(dev);
mvneta_port_down(pp);
mvneta_port_disable(pp);
}
static const struct eth_ops mvneta_ops = {
.start = mvneta_start,
.send = mvneta_send,
.recv = mvneta_recv,
.stop = mvneta_stop,
.write_hwaddr = mvneta_write_hwaddr,
};
static int mvneta_ofdata_to_platdata(struct udevice *dev)
{
struct eth_pdata *pdata = dev_get_platdata(dev);
const char *phy_mode;
pdata->iobase = devfdt_get_addr(dev);
/* Get phy-mode / phy_interface from DT */
pdata->phy_interface = -1;
phy_mode = fdt_getprop(gd->fdt_blob, dev_of_offset(dev), "phy-mode",
NULL);
if (phy_mode)
pdata->phy_interface = phy_get_interface_by_name(phy_mode);
if (pdata->phy_interface == -1) {
debug("%s: Invalid PHY interface '%s'\n", __func__, phy_mode);
return -EINVAL;
}
return 0;
}
static const struct udevice_id mvneta_ids[] = {
{ .compatible = "marvell,armada-370-neta" },
{ .compatible = "marvell,armada-xp-neta" },
{ .compatible = "marvell,armada-3700-neta" },
{ }
};
U_BOOT_DRIVER(mvneta) = {
.name = "mvneta",
.id = UCLASS_ETH,
.of_match = mvneta_ids,
.ofdata_to_platdata = mvneta_ofdata_to_platdata,
.probe = mvneta_probe,
.ops = &mvneta_ops,
.priv_auto_alloc_size = sizeof(struct mvneta_port),
.platdata_auto_alloc_size = sizeof(struct eth_pdata),
};