u-boot/include/configs/nas220.h
Tom Rini a09fea1d28 env: Finish migration of common ENV options
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00

106 lines
2.3 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2014 Evgeni Dobrev <evgeni@studio-punkt.com>
*
* based on work from:
* (C) Copyright 2009
* Marvell Semiconductor <www.marvell.com>
* Written-by: Prafulla Wadaskar <prafulla@marvell.com>
*/
#ifndef _CONFIG_NAS220_H
#define _CONFIG_NAS220_H
/*
* Machine type ID
*/
#define CONFIG_MACH_TYPE MACH_TYPE_RD88F6192_NAS
/*
* High Level Configuration Options (easy to change)
*/
#define CONFIG_FEROCEON_88FR131 /* #define CPU Core subversion */
#define CONFIG_KW88F6192 /* SOC Name */
#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
/* power-on led, regulator, sata0, sata1 */
#define NAS220_GE_OE_VAL_LOW ((1 << 12)|(1 << 14)|(1 << 24)|(1 << 28))
#define NAS220_GE_OE_VAL_HIGH (0)
#define NAS220_GE_OE_LOW (~((1 << 12)|(1 << 14)|(1 << 24)|(1 << 28)))
#define NAS220_GE_OE_HIGH (~(0))
/* PHY related */
#define MV88E1116_LED_FCTRL_REG 10
#define MV88E1116_CPRSP_CR3_REG 21
#define MV88E1116_MAC_CTRL_REG 21
#define MV88E1116_PGADR_REG 22
#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
/*
* Commands configuration
*/
/*
* mv-common.h should be defined after CMD configs since it used them
* to enable certain macros
*/
#include "mv-common.h"
/*
* Environment variables configurations
*/
/*
* Default environment variables
*/
#define CONFIG_BOOTCOMMAND ""
#define CONFIG_EXTRA_ENV_SETTINGS \
"bootargs=console=ttyS0,115200\0" \
"mtdparts=mtdparts=orion_nand:0xa0000@0x0(uboot),"\
"0x010000@0xa0000(env),"\
"0x500000@0xc0000(uimage),"\
"0x1a40000@0x5c0000(rootfs)\0" \
"mtdids=nand0=orion_nand\0"\
"autostart=no\0"\
"autoload=no\0"
/*
* Ethernet Driver configuration
*/
#ifdef CONFIG_CMD_NET
#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
#define CONFIG_PHY_BASE_ADR 8
#endif /* CONFIG_CMD_NET */
/*
* USB/EHCI
*/
#ifdef CONFIG_CMD_USB
#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */
#define CONFIG_EHCI_IS_TDI
#endif /* CONFIG_CMD_USB */
/*
* File system
*/
#define CONFIG_JFFS2_NAND
#define CONFIG_JFFS2_LZO
/*
* SATA
*/
#ifdef CONFIG_MVSATA_IDE
#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET
#endif
/*
* EFI partition
*/
#define CONFIG_KIRKWOOD_GPIO
#endif /* _CONFIG_NAS220_H */