u-boot/include/configs/xtfpga.h
Philipp Tomsich f40574e2d7 Kconfig: Migrate CONFIG_BAUDRATE
Move this in to Kconfig with a default of 115200.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[trini: Run moveconfig.py, reword commit slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-19 14:48:37 -04:00

264 lines
8.5 KiB
C

/*
* Copyright (C) 2007-2013 Tensilica, Inc.
* Copyright (C) 2014 - 2016 Cadence Design Systems Inc.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include <asm/arch/core.h>
#include <asm/addrspace.h>
#include <asm/config.h>
/*
* The 'xtfpga' board describes a set of very similar boards with only minimal
* differences.
*/
/*=====================*/
/* Board and Processor */
/*=====================*/
#define CONFIG_XTFPGA
/* FPGA CPU freq after init */
#define CONFIG_SYS_CLK_FREQ (gd->cpu_clk)
/*===================*/
/* RAM Layout */
/*===================*/
#if XCHAL_HAVE_PTP_MMU
#define CONFIG_SYS_MEMORY_BASE \
(XCHAL_VECBASE_RESET_VADDR - XCHAL_VECBASE_RESET_PADDR)
#define CONFIG_SYS_IO_BASE 0xf0000000
#else
#define CONFIG_SYS_MEMORY_BASE 0x60000000
#define CONFIG_SYS_IO_BASE 0x90000000
#define CONFIG_MAX_MEM_MAPPED 0x10000000
#endif
/* Onboard RAM sizes:
*
* LX60 0x04000000 64 MB
* LX110 0x03000000 48 MB
* LX200 0x06000000 96 MB
* ML605 0x18000000 384 MB
* KC705 0x38000000 896 MB
*
* noMMU configurations can only see first 256MB of onboard memory.
*/
#if XCHAL_HAVE_PTP_MMU || CONFIG_BOARD_SDRAM_SIZE < 0x10000000
#define CONFIG_SYS_SDRAM_SIZE CONFIG_BOARD_SDRAM_SIZE
#else
#define CONFIG_SYS_SDRAM_SIZE 0x10000000
#endif
#define CONFIG_SYS_SDRAM_BASE MEMADDR(0x00000000)
/* Lx60 can only map 128kb memory (instead of 256kb) when running under OCD */
#ifdef CONFIG_XTFPGA_LX60
# define CONFIG_SYS_MONITOR_LEN 0x00020000 /* 128KB */
#else
# define CONFIG_SYS_MONITOR_LEN 0x00040000 /* 256KB */
#endif
#define CONFIG_SYS_STACKSIZE (512 << 10) /* stack 512KB */
#define CONFIG_SYS_MALLOC_LEN (256 << 10) /* heap 256KB */
/* Linux boot param area in RAM (used only when booting linux) */
#define CONFIG_SYS_BOOTPARAMS_LEN (64 << 10)
/* Memory test is destructive so default must not overlap vectors or U-Boot*/
#define CONFIG_SYS_MEMTEST_START MEMADDR(0x01000000)
#define CONFIG_SYS_MEMTEST_END MEMADDR(0x02000000)
/* Load address for stand-alone applications.
* MEMADDR cannot be used here, because the definition needs to be
* a plain number as it's used as -Ttext argument for ld in standalone
* example makefile.
* Handle noMMU vs MMUv2 vs MMUv3 distinction here manually.
*/
#if XCHAL_HAVE_PTP_MMU
#if XCHAL_VECBASE_RESET_VADDR == XCHAL_VECBASE_RESET_PADDR
#define CONFIG_STANDALONE_LOAD_ADDR 0x00800000
#else
#define CONFIG_STANDALONE_LOAD_ADDR 0xd0800000
#endif
#else
#define CONFIG_STANDALONE_LOAD_ADDR 0x60800000
#endif
#if defined(CONFIG_MAX_MEM_MAPPED) && \
CONFIG_MAX_MEM_MAPPED < CONFIG_SYS_SDRAM_SIZE
#define CONFIG_SYS_MEMORY_SIZE CONFIG_MAX_MEM_MAPPED
#else
#define CONFIG_SYS_MEMORY_SIZE CONFIG_SYS_SDRAM_SIZE
#endif
#define CONFIG_SYS_MEMORY_TOP MEMADDR(CONFIG_SYS_MEMORY_SIZE)
#define CONFIG_SYS_TEXT_ADDR \
(CONFIG_SYS_MEMORY_TOP - CONFIG_SYS_MONITOR_LEN)
/* Used by tftpboot; env var 'loadaddr' */
#define CONFIG_SYS_LOAD_ADDR MEMADDR(0x02000000)
/*==============================*/
/* U-Boot general configuration */
/*==============================*/
#undef CONFIG_USE_IRQ /* Keep it simple, poll only */
#define CONFIG_BOARD_POSTCLK_INIT
#define CONFIG_MISC_INIT_R
#define CONFIG_BOOTFILE "uImage"
/* Console I/O Buffer Size */
#define CONFIG_SYS_CBSIZE 1024
/* Prt buf */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
/* max number of command args */
#define CONFIG_SYS_MAXARGS 16
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
/*=================*/
/* U-Boot commands */
/*=================*/
#define CONFIG_CMD_DIAG
#define CONFIG_CMD_SAVES
/*==============================*/
/* U-Boot autoboot configuration */
/*==============================*/
#define CONFIG_BOOT_RETRY_TIME 60 /* retry after 60 secs */
#define CONFIG_AUTO_COMPLETE /* Support tab autocompletion */
#define CONFIG_CMDLINE_EDITING
#define CONFIG_SYS_LONGHELP
#define CONFIG_CRC32_VERIFY
#define CONFIG_MX_CYCLIC
#define CONFIG_SHOW_BOOT_PROGRESS
#ifdef DEBUG
#define CONFIG_PANIC_HANG 1 /* Require manual reboot */
#endif
/*=========================================*/
/* FPGA Registers (board info and control) */
/*=========================================*/
/*
* These assume FPGA bitstreams from Tensilica release RB and up. Earlier
* releases may not provide any/all of these registers or at these offsets.
* Some of the FPGA registers are broken down into bitfields described by
* SHIFT left amount and field WIDTH (bits), and also by a bitMASK.
*/
/* Date of FPGA bitstream build in binary coded decimal (BCD) */
#define CONFIG_SYS_FPGAREG_DATE IOADDR(0x0D020000)
#define FPGAREG_MTH_SHIFT 24 /* BCD month 1..12 */
#define FPGAREG_MTH_WIDTH 8
#define FPGAREG_MTH_MASK 0xFF000000
#define FPGAREG_DAY_SHIFT 16 /* BCD day 1..31 */
#define FPGAREG_DAY_WIDTH 8
#define FPGAREG_DAY_MASK 0x00FF0000
#define FPGAREG_YEAR_SHIFT 0 /* BCD year 2001..9999*/
#define FPGAREG_YEAR_WIDTH 16
#define FPGAREG_YEAR_MASK 0x0000FFFF
/* FPGA core clock frequency in Hz (also input to UART) */
#define CONFIG_SYS_FPGAREG_FREQ IOADDR(0x0D020004) /* CPU clock frequency*/
/*
* DIP switch (left=sw1=lsb=bit0, right=sw8=msb=bit7; off=0, on=1):
* Bits 0..5 set the lower 6 bits of the default ethernet MAC.
* Bit 6 is reserved for future use by Tensilica.
* Bit 7 maps the first 128KB of ROM address space at CONFIG_SYS_ROM_BASE to
* the base of flash * (when on/1) or to the base of RAM (when off/0).
*/
#define CONFIG_SYS_FPGAREG_DIPSW IOADDR(0x0D02000C)
#define FPGAREG_MAC_SHIFT 0 /* Ethernet MAC bits 0..5 */
#define FPGAREG_MAC_WIDTH 6
#define FPGAREG_MAC_MASK 0x3f
#define FPGAREG_BOOT_SHIFT 7 /* Boot ROM addr mapping */
#define FPGAREG_BOOT_WIDTH 1
#define FPGAREG_BOOT_MASK 0x80
#define FPGAREG_BOOT_RAM 0
#define FPGAREG_BOOT_FLASH (1<<FPGAREG_BOOT_SHIFT)
/* Force hard reset of board by writing a code to this register */
#define CONFIG_SYS_FPGAREG_RESET IOADDR(0x0D020010) /* Reset board .. */
#define CONFIG_SYS_FPGAREG_RESET_CODE 0x0000DEAD /* by writing this code */
/*====================*/
/* Serial Driver Info */
/*====================*/
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE (-4)
#define CONFIG_SYS_NS16550_COM1 IOADDR(0x0D050020) /* Base address */
/* Input clk to NS16550 (in Hz; the SYS_CLK_FREQ is in kHz) */
#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_CLK_FREQ
#define CONFIG_CONS_INDEX 1 /* use UART0 for console */
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*======================*/
/* Ethernet Driver Info */
/*======================*/
#define CONFIG_ETHBASE 00:50:C2:13:6f:00
#define CONFIG_SYS_ETHOC_BASE IOADDR(0x0d030000)
#define CONFIG_SYS_ETHOC_BUFFER_ADDR IOADDR(0x0D800000)
/*=====================*/
/* Flash & Environment */
/*=====================*/
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_FLASH_CFI_DRIVER /* use generic CFI driver */
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
#define CONFIG_SYS_MAX_FLASH_BANKS 1
#ifdef CONFIG_XTFPGA_LX60
# define CONFIG_SYS_FLASH_SIZE 0x0040000 /* 4MB */
# define CONFIG_SYS_FLASH_SECT_SZ 0x10000 /* block size 64KB */
# define CONFIG_SYS_FLASH_PARMSECT_SZ 0x2000 /* param size 8KB */
# define CONFIG_SYS_FLASH_BASE IOADDR(0x08000000)
# define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#elif defined(CONFIG_XTFPGA_KC705)
# define CONFIG_SYS_FLASH_SIZE 0x8000000 /* 128MB */
# define CONFIG_SYS_FLASH_SECT_SZ 0x20000 /* block size 128KB */
# define CONFIG_SYS_FLASH_PARMSECT_SZ 0x8000 /* param size 32KB */
# define CONFIG_SYS_FLASH_BASE IOADDR(0x00000000)
# define CONFIG_SYS_MONITOR_BASE IOADDR(0x06000000)
#else
# define CONFIG_SYS_FLASH_SIZE 0x1000000 /* 16MB */
# define CONFIG_SYS_FLASH_SECT_SZ 0x20000 /* block size 128KB */
# define CONFIG_SYS_FLASH_PARMSECT_SZ 0x8000 /* param size 32KB */
# define CONFIG_SYS_FLASH_BASE IOADDR(0x08000000)
# define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#endif
#define CONFIG_SYS_MAX_FLASH_SECT \
(CONFIG_SYS_FLASH_SECT_SZ/CONFIG_SYS_FLASH_PARMSECT_SZ + \
CONFIG_SYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ - 1)
#define CONFIG_SYS_FLASH_PROTECTION /* hw flash protection */
/*
* Put environment in top block (64kB)
* Another option would be to put env. in 2nd param block offs 8KB, size 8KB
*/
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_OFFSET (CONFIG_SYS_FLASH_SIZE - CONFIG_SYS_FLASH_SECT_SZ)
#define CONFIG_ENV_SIZE CONFIG_SYS_FLASH_SECT_SZ
/* print 'E' for empty sector on flinfo */
#define CONFIG_SYS_FLASH_EMPTY_INFO
#endif /* __CONFIG_H */