u-boot/arch/arm/mach-orion5x/cpu.c
Masahiro Yamada 3e93b4e600 ARM: orion5x: move SoC sources to mach-orion5x
Move
arch/arm/cpu/arm926ejs/orion5x/* -> arch/arm/mach-orion5x/*

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2015-02-21 08:23:51 -05:00

294 lines
8.8 KiB
C

/*
* Copyright (C) 2010 Albert ARIBAUD <albert.u.boot@aribaud.net>
*
* Based on original Kirkwood support which is
* (C) Copyright 2009
* Marvell Semiconductor <www.marvell.com>
* Written-by: Prafulla Wadaskar <prafulla@marvell.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <netdev.h>
#include <asm/cache.h>
#include <asm/io.h>
#include <u-boot/md5.h>
#include <asm/arch/cpu.h>
#define BUFLEN 16
void reset_cpu(unsigned long ignored)
{
struct orion5x_cpu_registers *cpureg =
(struct orion5x_cpu_registers *)ORION5X_CPU_REG_BASE;
writel(readl(&cpureg->rstoutn_mask) | (1 << 2),
&cpureg->rstoutn_mask);
writel(readl(&cpureg->sys_soft_rst) | 1,
&cpureg->sys_soft_rst);
while (1)
;
}
/*
* Compute Window Size field value from size expressed in bytes
* Used with the Base register to set the address window size and location.
* Must be programmed from LSB to MSB as sequence of ones followed by
* sequence of zeros. The number of ones specifies the size of the window in
* 64 KiB granularity (e.g., a value of 0x00FF specifies 256 = 16 MiB).
* NOTES:
* 1) A sizeval equal to 0x0 specifies 4 GiB.
* 2) A return value of 0x0 specifies 64 KiB.
*/
unsigned int orion5x_winctrl_calcsize(unsigned int sizeval)
{
/*
* Calculate the number of 64 KiB blocks needed minus one (rounding up).
* For sizeval > 0 this is equivalent to:
* sizeval = (u32) ceil((double) sizeval / 65536.0) - 1
*/
sizeval = (sizeval - 1) >> 16;
/*
* Propagate 'one' bits to the right by 'oring' them.
* We need only treat bits 15-0.
*/
sizeval |= sizeval >> 1; /* 'Or' bit 15 onto bit 14 */
sizeval |= sizeval >> 2; /* 'Or' bits 15-14 onto bits 13-12 */
sizeval |= sizeval >> 4; /* 'Or' bits 15-12 onto bits 11-8 */
sizeval |= sizeval >> 8; /* 'Or' bits 15-8 onto bits 7-0*/
return sizeval;
}
/*
* orion5x_config_adr_windows - Configure address Windows
*
* There are 8 address windows supported by Orion5x Soc to addess different
* devices. Each window can be configured for size, BAR and remap addr
* Below configuration is standard for most of the cases
*
* If remap function not used, remap_lo must be set as base
*
* NOTES:
*
* 1) in order to avoid windows with inconsistent control and base values
* (which could prevent access to BOOTCS and hence execution from FLASH)
* always disable window before writing the base value then reenable it
* by writing the control value.
*
* 2) in order to avoid losing access to BOOTCS when disabling window 7,
* first configure window 6 for BOOTCS, then configure window 7 for BOOTCS,
* then configure windows 6 for its own target.
*
* Reference Documentation:
* Mbus-L to Mbus Bridge Registers Configuration.
* (Sec 25.1 and 25.3 of Datasheet)
*/
int orion5x_config_adr_windows(void)
{
struct orion5x_win_registers *winregs =
(struct orion5x_win_registers *)ORION5X_CPU_WIN_BASE;
/* Disable window 0, configure it for its intended target, enable it. */
writel(0, &winregs[0].ctrl);
writel(ORION5X_ADR_PCIE_MEM, &winregs[0].base);
writel(ORION5X_ADR_PCIE_MEM_REMAP_LO, &winregs[0].remap_lo);
writel(ORION5X_ADR_PCIE_MEM_REMAP_HI, &winregs[0].remap_hi);
writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_PCIE_MEM,
ORION5X_TARGET_PCIE, ORION5X_ATTR_PCIE_MEM,
ORION5X_WIN_ENABLE), &winregs[0].ctrl);
/* Disable window 1, configure it for its intended target, enable it. */
writel(0, &winregs[1].ctrl);
writel(ORION5X_ADR_PCIE_IO, &winregs[1].base);
writel(ORION5X_ADR_PCIE_IO_REMAP_LO, &winregs[1].remap_lo);
writel(ORION5X_ADR_PCIE_IO_REMAP_HI, &winregs[1].remap_hi);
writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_PCIE_IO,
ORION5X_TARGET_PCIE, ORION5X_ATTR_PCIE_IO,
ORION5X_WIN_ENABLE), &winregs[1].ctrl);
/* Disable window 2, configure it for its intended target, enable it. */
writel(0, &winregs[2].ctrl);
writel(ORION5X_ADR_PCI_MEM, &winregs[2].base);
writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_PCI_MEM,
ORION5X_TARGET_PCI, ORION5X_ATTR_PCI_MEM,
ORION5X_WIN_ENABLE), &winregs[2].ctrl);
/* Disable window 3, configure it for its intended target, enable it. */
writel(0, &winregs[3].ctrl);
writel(ORION5X_ADR_PCI_IO, &winregs[3].base);
writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_PCI_IO,
ORION5X_TARGET_PCI, ORION5X_ATTR_PCI_IO,
ORION5X_WIN_ENABLE), &winregs[3].ctrl);
/* Disable window 4, configure it for its intended target, enable it. */
writel(0, &winregs[4].ctrl);
writel(ORION5X_ADR_DEV_CS0, &winregs[4].base);
writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_DEV_CS0,
ORION5X_TARGET_DEVICE, ORION5X_ATTR_DEV_CS0,
ORION5X_WIN_ENABLE), &winregs[4].ctrl);
/* Disable window 5, configure it for its intended target, enable it. */
writel(0, &winregs[5].ctrl);
writel(ORION5X_ADR_DEV_CS1, &winregs[5].base);
writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_DEV_CS1,
ORION5X_TARGET_DEVICE, ORION5X_ATTR_DEV_CS1,
ORION5X_WIN_ENABLE), &winregs[5].ctrl);
/* Disable window 6, configure it for FLASH, enable it. */
writel(0, &winregs[6].ctrl);
writel(ORION5X_ADR_BOOTROM, &winregs[6].base);
writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_BOOTROM,
ORION5X_TARGET_DEVICE, ORION5X_ATTR_BOOTROM,
ORION5X_WIN_ENABLE), &winregs[6].ctrl);
/* Disable window 7, configure it for FLASH, enable it. */
writel(0, &winregs[7].ctrl);
writel(ORION5X_ADR_BOOTROM, &winregs[7].base);
writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_BOOTROM,
ORION5X_TARGET_DEVICE, ORION5X_ATTR_BOOTROM,
ORION5X_WIN_ENABLE), &winregs[7].ctrl);
/* Disable window 6, configure it for its intended target, enable it. */
writel(0, &winregs[6].ctrl);
writel(ORION5X_ADR_DEV_CS2, &winregs[6].base);
writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_DEV_CS2,
ORION5X_TARGET_DEVICE, ORION5X_ATTR_DEV_CS2,
ORION5X_WIN_ENABLE), &winregs[6].ctrl);
return 0;
}
/*
* Orion5x identification is done through PCIE space.
*/
u32 orion5x_device_id(void)
{
return readl(PCIE_DEV_ID_OFF) >> 16;
}
u32 orion5x_device_rev(void)
{
return readl(PCIE_DEV_REV_OFF) & 0xff;
}
#if defined(CONFIG_DISPLAY_CPUINFO)
/* Display device and revision IDs.
* This function must cover all known device/revision
* combinations, not only the one for which u-boot is
* compiled; this way, one can identify actual HW in
* case of a mismatch.
*/
int print_cpuinfo(void)
{
char dev_str[7]; /* room enough for 0x0000 plus null byte */
char rev_str[5]; /* room enough for 0x00 plus null byte */
char *dev_name = NULL;
char *rev_name = NULL;
u32 dev = orion5x_device_id();
u32 rev = orion5x_device_rev();
if (dev == MV88F5181_DEV_ID) {
dev_name = "MV88F5181";
if (rev == MV88F5181_REV_B1)
rev_name = "B1";
else if (rev == MV88F5181L_REV_A1) {
dev_name = "MV88F5181L";
rev_name = "A1";
} else if (rev == MV88F5181L_REV_A0) {
dev_name = "MV88F5181L";
rev_name = "A0";
}
} else if (dev == MV88F5182_DEV_ID) {
dev_name = "MV88F5182";
if (rev == MV88F5182_REV_A2)
rev_name = "A2";
} else if (dev == MV88F5281_DEV_ID) {
dev_name = "MV88F5281";
if (rev == MV88F5281_REV_D2)
rev_name = "D2";
else if (rev == MV88F5281_REV_D1)
rev_name = "D1";
else if (rev == MV88F5281_REV_D0)
rev_name = "D0";
} else if (dev == MV88F6183_DEV_ID) {
dev_name = "MV88F6183";
if (rev == MV88F6183_REV_B0)
rev_name = "B0";
}
if (dev_name == NULL) {
sprintf(dev_str, "0x%04x", dev);
dev_name = dev_str;
}
if (rev_name == NULL) {
sprintf(rev_str, "0x%02x", rev);
rev_name = rev_str;
}
printf("SoC: Orion5x %s-%s\n", dev_name, rev_name);
return 0;
}
#endif /* CONFIG_DISPLAY_CPUINFO */
#ifdef CONFIG_ARCH_CPU_INIT
int arch_cpu_init(void)
{
/* Enable and invalidate L2 cache in write through mode */
invalidate_l2_cache();
orion5x_config_adr_windows();
return 0;
}
#endif /* CONFIG_ARCH_CPU_INIT */
/*
* SOC specific misc init
*/
#if defined(CONFIG_ARCH_MISC_INIT)
int arch_misc_init(void)
{
u32 temp;
/*CPU streaming & write allocate */
temp = readfr_extra_feature_reg();
temp &= ~(1 << 28); /* disable wr alloc */
writefr_extra_feature_reg(temp);
temp = readfr_extra_feature_reg();
temp &= ~(1 << 29); /* streaming disabled */
writefr_extra_feature_reg(temp);
/* L2Cache settings */
temp = readfr_extra_feature_reg();
/* Disable L2C pre fetch - Set bit 24 */
temp |= (1 << 24);
/* enable L2C - Set bit 22 */
temp |= (1 << 22);
writefr_extra_feature_reg(temp);
icache_enable();
/* Change reset vector to address 0x0 */
temp = get_cr();
set_cr(temp & ~CR_V);
/* Set CPIOs and MPPs - values provided by board
include file */
writel(ORION5X_MPP0_7, ORION5X_MPP_BASE+0x00);
writel(ORION5X_MPP8_15, ORION5X_MPP_BASE+0x04);
writel(ORION5X_MPP16_23, ORION5X_MPP_BASE+0x50);
writel(ORION5X_GPIO_OUT_VALUE, ORION5X_GPIO_BASE+0x00);
writel(ORION5X_GPIO_OUT_ENABLE, ORION5X_GPIO_BASE+0x04);
writel(ORION5X_GPIO_IN_POLARITY, ORION5X_GPIO_BASE+0x0c);
/* initialize timer */
timer_init_r();
return 0;
}
#endif /* CONFIG_ARCH_MISC_INIT */
#ifdef CONFIG_MVGBE
int cpu_eth_init(bd_t *bis)
{
mvgbe_initialize(bis);
return 0;
}
#endif