mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-26 22:52:18 +00:00
34e026f9b1
Mostly reusing DDR3 driver, this patch adds DDR4 SPD handling, register calculation and programming. Signed-off-by: York Sun <yorksun@freescale.com>
565 lines
24 KiB
C
565 lines
24 KiB
C
/*
|
|
* Copyright 2008-2014 Freescale Semiconductor, Inc.
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License
|
|
* Version 2 as published by the Free Software Foundation.
|
|
*/
|
|
|
|
#ifndef _DDR_SPD_H_
|
|
#define _DDR_SPD_H_
|
|
|
|
/*
|
|
* Format from "JEDEC Standard No. 21-C,
|
|
* Appendix D: Rev 1.0: SPD's for DDR SDRAM
|
|
*/
|
|
typedef struct ddr1_spd_eeprom_s {
|
|
unsigned char info_size; /* 0 # bytes written into serial memory */
|
|
unsigned char chip_size; /* 1 Total # bytes of SPD memory device */
|
|
unsigned char mem_type; /* 2 Fundamental memory type */
|
|
unsigned char nrow_addr; /* 3 # of Row Addresses on this assembly */
|
|
unsigned char ncol_addr; /* 4 # of Column Addrs on this assembly */
|
|
unsigned char nrows; /* 5 Number of DIMM Banks */
|
|
unsigned char dataw_lsb; /* 6 Data Width of this assembly */
|
|
unsigned char dataw_msb; /* 7 ... Data Width continuation */
|
|
unsigned char voltage; /* 8 Voltage intf std of this assembly */
|
|
unsigned char clk_cycle; /* 9 SDRAM Cycle time @ CL=X */
|
|
unsigned char clk_access; /* 10 SDRAM Access from Clk @ CL=X (tAC) */
|
|
unsigned char config; /* 11 DIMM Configuration type */
|
|
unsigned char refresh; /* 12 Refresh Rate/Type */
|
|
unsigned char primw; /* 13 Primary SDRAM Width */
|
|
unsigned char ecw; /* 14 Error Checking SDRAM width */
|
|
unsigned char min_delay; /* 15 for Back to Back Random Address */
|
|
unsigned char burstl; /* 16 Burst Lengths Supported */
|
|
unsigned char nbanks; /* 17 # of Banks on SDRAM Device */
|
|
unsigned char cas_lat; /* 18 CAS# Latencies Supported */
|
|
unsigned char cs_lat; /* 19 CS# Latency */
|
|
unsigned char write_lat; /* 20 Write Latency (aka Write Recovery) */
|
|
unsigned char mod_attr; /* 21 SDRAM Module Attributes */
|
|
unsigned char dev_attr; /* 22 SDRAM Device Attributes */
|
|
unsigned char clk_cycle2; /* 23 Min SDRAM Cycle time @ CL=X-0.5 */
|
|
unsigned char clk_access2; /* 24 SDRAM Access from
|
|
Clk @ CL=X-0.5 (tAC) */
|
|
unsigned char clk_cycle3; /* 25 Min SDRAM Cycle time @ CL=X-1 */
|
|
unsigned char clk_access3; /* 26 Max Access from Clk @ CL=X-1 (tAC) */
|
|
unsigned char trp; /* 27 Min Row Precharge Time (tRP)*/
|
|
unsigned char trrd; /* 28 Min Row Active to Row Active (tRRD) */
|
|
unsigned char trcd; /* 29 Min RAS to CAS Delay (tRCD) */
|
|
unsigned char tras; /* 30 Minimum RAS Pulse Width (tRAS) */
|
|
unsigned char bank_dens; /* 31 Density of each bank on module */
|
|
unsigned char ca_setup; /* 32 Addr + Cmd Setup Time Before Clk */
|
|
unsigned char ca_hold; /* 33 Addr + Cmd Hold Time After Clk */
|
|
unsigned char data_setup; /* 34 Data Input Setup Time Before Strobe */
|
|
unsigned char data_hold; /* 35 Data Input Hold Time After Strobe */
|
|
unsigned char res_36_40[5];/* 36-40 reserved for VCSDRAM */
|
|
unsigned char trc; /* 41 Min Active to Auto refresh time tRC */
|
|
unsigned char trfc; /* 42 Min Auto to Active period tRFC */
|
|
unsigned char tckmax; /* 43 Max device cycle time tCKmax */
|
|
unsigned char tdqsq; /* 44 Max DQS to DQ skew (tDQSQ max) */
|
|
unsigned char tqhs; /* 45 Max Read DataHold skew (tQHS) */
|
|
unsigned char res_46; /* 46 Reserved */
|
|
unsigned char dimm_height; /* 47 DDR SDRAM DIMM Height */
|
|
unsigned char res_48_61[14]; /* 48-61 Reserved */
|
|
unsigned char spd_rev; /* 62 SPD Data Revision Code */
|
|
unsigned char cksum; /* 63 Checksum for bytes 0-62 */
|
|
unsigned char mid[8]; /* 64-71 Mfr's JEDEC ID code per JEP-106 */
|
|
unsigned char mloc; /* 72 Manufacturing Location */
|
|
unsigned char mpart[18]; /* 73 Manufacturer's Part Number */
|
|
unsigned char rev[2]; /* 91 Revision Code */
|
|
unsigned char mdate[2]; /* 93 Manufacturing Date */
|
|
unsigned char sernum[4]; /* 95 Assembly Serial Number */
|
|
unsigned char mspec[27]; /* 99-127 Manufacturer Specific Data */
|
|
|
|
} ddr1_spd_eeprom_t;
|
|
|
|
/*
|
|
* Format from "JEDEC Appendix X: Serial Presence Detects for DDR2 SDRAM",
|
|
* SPD Revision 1.2
|
|
*/
|
|
typedef struct ddr2_spd_eeprom_s {
|
|
unsigned char info_size; /* 0 # bytes written into serial memory */
|
|
unsigned char chip_size; /* 1 Total # bytes of SPD memory device */
|
|
unsigned char mem_type; /* 2 Fundamental memory type */
|
|
unsigned char nrow_addr; /* 3 # of Row Addresses on this assembly */
|
|
unsigned char ncol_addr; /* 4 # of Column Addrs on this assembly */
|
|
unsigned char mod_ranks; /* 5 Number of DIMM Ranks */
|
|
unsigned char dataw; /* 6 Module Data Width */
|
|
unsigned char res_7; /* 7 Reserved */
|
|
unsigned char voltage; /* 8 Voltage intf std of this assembly */
|
|
unsigned char clk_cycle; /* 9 SDRAM Cycle time @ CL=X */
|
|
unsigned char clk_access; /* 10 SDRAM Access from Clk @ CL=X (tAC) */
|
|
unsigned char config; /* 11 DIMM Configuration type */
|
|
unsigned char refresh; /* 12 Refresh Rate/Type */
|
|
unsigned char primw; /* 13 Primary SDRAM Width */
|
|
unsigned char ecw; /* 14 Error Checking SDRAM width */
|
|
unsigned char res_15; /* 15 Reserved */
|
|
unsigned char burstl; /* 16 Burst Lengths Supported */
|
|
unsigned char nbanks; /* 17 # of Banks on Each SDRAM Device */
|
|
unsigned char cas_lat; /* 18 CAS# Latencies Supported */
|
|
unsigned char mech_char; /* 19 DIMM Mechanical Characteristics */
|
|
unsigned char dimm_type; /* 20 DIMM type information */
|
|
unsigned char mod_attr; /* 21 SDRAM Module Attributes */
|
|
unsigned char dev_attr; /* 22 SDRAM Device Attributes */
|
|
unsigned char clk_cycle2; /* 23 Min SDRAM Cycle time @ CL=X-1 */
|
|
unsigned char clk_access2; /* 24 SDRAM Access from Clk @ CL=X-1 (tAC) */
|
|
unsigned char clk_cycle3; /* 25 Min SDRAM Cycle time @ CL=X-2 */
|
|
unsigned char clk_access3; /* 26 Max Access from Clk @ CL=X-2 (tAC) */
|
|
unsigned char trp; /* 27 Min Row Precharge Time (tRP)*/
|
|
unsigned char trrd; /* 28 Min Row Active to Row Active (tRRD) */
|
|
unsigned char trcd; /* 29 Min RAS to CAS Delay (tRCD) */
|
|
unsigned char tras; /* 30 Minimum RAS Pulse Width (tRAS) */
|
|
unsigned char rank_dens; /* 31 Density of each rank on module */
|
|
unsigned char ca_setup; /* 32 Addr+Cmd Setup Time Before Clk (tIS) */
|
|
unsigned char ca_hold; /* 33 Addr+Cmd Hold Time After Clk (tIH) */
|
|
unsigned char data_setup; /* 34 Data Input Setup Time
|
|
Before Strobe (tDS) */
|
|
unsigned char data_hold; /* 35 Data Input Hold Time
|
|
After Strobe (tDH) */
|
|
unsigned char twr; /* 36 Write Recovery time tWR */
|
|
unsigned char twtr; /* 37 Int write to read delay tWTR */
|
|
unsigned char trtp; /* 38 Int read to precharge delay tRTP */
|
|
unsigned char mem_probe; /* 39 Mem analysis probe characteristics */
|
|
unsigned char trctrfc_ext; /* 40 Extensions to trc and trfc */
|
|
unsigned char trc; /* 41 Min Active to Auto refresh time tRC */
|
|
unsigned char trfc; /* 42 Min Auto to Active period tRFC */
|
|
unsigned char tckmax; /* 43 Max device cycle time tCKmax */
|
|
unsigned char tdqsq; /* 44 Max DQS to DQ skew (tDQSQ max) */
|
|
unsigned char tqhs; /* 45 Max Read DataHold skew (tQHS) */
|
|
unsigned char pll_relock; /* 46 PLL Relock time */
|
|
unsigned char t_casemax; /* 47 Tcasemax */
|
|
unsigned char psi_ta_dram; /* 48 Thermal Resistance of DRAM Package from
|
|
Top (Case) to Ambient (Psi T-A DRAM) */
|
|
unsigned char dt0_mode; /* 49 DRAM Case Temperature Rise from Ambient
|
|
due to Activate-Precharge/Mode Bits
|
|
(DT0/Mode Bits) */
|
|
unsigned char dt2n_dt2q; /* 50 DRAM Case Temperature Rise from Ambient
|
|
due to Precharge/Quiet Standby
|
|
(DT2N/DT2Q) */
|
|
unsigned char dt2p; /* 51 DRAM Case Temperature Rise from Ambient
|
|
due to Precharge Power-Down (DT2P) */
|
|
unsigned char dt3n; /* 52 DRAM Case Temperature Rise from Ambient
|
|
due to Active Standby (DT3N) */
|
|
unsigned char dt3pfast; /* 53 DRAM Case Temperature Rise from Ambient
|
|
due to Active Power-Down with
|
|
Fast PDN Exit (DT3Pfast) */
|
|
unsigned char dt3pslow; /* 54 DRAM Case Temperature Rise from Ambient
|
|
due to Active Power-Down with Slow
|
|
PDN Exit (DT3Pslow) */
|
|
unsigned char dt4r_dt4r4w; /* 55 DRAM Case Temperature Rise from Ambient
|
|
due to Page Open Burst Read/DT4R4W
|
|
Mode Bit (DT4R/DT4R4W Mode Bit) */
|
|
unsigned char dt5b; /* 56 DRAM Case Temperature Rise from Ambient
|
|
due to Burst Refresh (DT5B) */
|
|
unsigned char dt7; /* 57 DRAM Case Temperature Rise from Ambient
|
|
due to Bank Interleave Reads with
|
|
Auto-Precharge (DT7) */
|
|
unsigned char psi_ta_pll; /* 58 Thermal Resistance of PLL Package form
|
|
Top (Case) to Ambient (Psi T-A PLL) */
|
|
unsigned char psi_ta_reg; /* 59 Thermal Reisitance of Register Package
|
|
from Top (Case) to Ambient
|
|
(Psi T-A Register) */
|
|
unsigned char dtpllactive; /* 60 PLL Case Temperature Rise from Ambient
|
|
due to PLL Active (DT PLL Active) */
|
|
unsigned char dtregact; /* 61 Register Case Temperature Rise from
|
|
Ambient due to Register Active/Mode Bit
|
|
(DT Register Active/Mode Bit) */
|
|
unsigned char spd_rev; /* 62 SPD Data Revision Code */
|
|
unsigned char cksum; /* 63 Checksum for bytes 0-62 */
|
|
unsigned char mid[8]; /* 64 Mfr's JEDEC ID code per JEP-106 */
|
|
unsigned char mloc; /* 72 Manufacturing Location */
|
|
unsigned char mpart[18]; /* 73 Manufacturer's Part Number */
|
|
unsigned char rev[2]; /* 91 Revision Code */
|
|
unsigned char mdate[2]; /* 93 Manufacturing Date */
|
|
unsigned char sernum[4]; /* 95 Assembly Serial Number */
|
|
unsigned char mspec[27]; /* 99-127 Manufacturer Specific Data */
|
|
|
|
} ddr2_spd_eeprom_t;
|
|
|
|
typedef struct ddr3_spd_eeprom_s {
|
|
/* General Section: Bytes 0-59 */
|
|
unsigned char info_size_crc; /* 0 # bytes written into serial memory,
|
|
CRC coverage */
|
|
unsigned char spd_rev; /* 1 Total # bytes of SPD mem device */
|
|
unsigned char mem_type; /* 2 Key Byte / Fundamental mem type */
|
|
unsigned char module_type; /* 3 Key Byte / Module Type */
|
|
unsigned char density_banks; /* 4 SDRAM Density and Banks */
|
|
unsigned char addressing; /* 5 SDRAM Addressing */
|
|
unsigned char module_vdd; /* 6 Module nominal voltage, VDD */
|
|
unsigned char organization; /* 7 Module Organization */
|
|
unsigned char bus_width; /* 8 Module Memory Bus Width */
|
|
unsigned char ftb_div; /* 9 Fine Timebase (FTB)
|
|
Dividend / Divisor */
|
|
unsigned char mtb_dividend; /* 10 Medium Timebase (MTB) Dividend */
|
|
unsigned char mtb_divisor; /* 11 Medium Timebase (MTB) Divisor */
|
|
unsigned char tck_min; /* 12 SDRAM Minimum Cycle Time */
|
|
unsigned char res_13; /* 13 Reserved */
|
|
unsigned char caslat_lsb; /* 14 CAS Latencies Supported,
|
|
Least Significant Byte */
|
|
unsigned char caslat_msb; /* 15 CAS Latencies Supported,
|
|
Most Significant Byte */
|
|
unsigned char taa_min; /* 16 Min CAS Latency Time */
|
|
unsigned char twr_min; /* 17 Min Write REcovery Time */
|
|
unsigned char trcd_min; /* 18 Min RAS# to CAS# Delay Time */
|
|
unsigned char trrd_min; /* 19 Min Row Active to
|
|
Row Active Delay Time */
|
|
unsigned char trp_min; /* 20 Min Row Precharge Delay Time */
|
|
unsigned char tras_trc_ext; /* 21 Upper Nibbles for tRAS and tRC */
|
|
unsigned char tras_min_lsb; /* 22 Min Active to Precharge
|
|
Delay Time */
|
|
unsigned char trc_min_lsb; /* 23 Min Active to Active/Refresh
|
|
Delay Time, LSB */
|
|
unsigned char trfc_min_lsb; /* 24 Min Refresh Recovery Delay Time */
|
|
unsigned char trfc_min_msb; /* 25 Min Refresh Recovery Delay Time */
|
|
unsigned char twtr_min; /* 26 Min Internal Write to
|
|
Read Command Delay Time */
|
|
unsigned char trtp_min; /* 27 Min Internal Read to Precharge
|
|
Command Delay Time */
|
|
unsigned char tfaw_msb; /* 28 Upper Nibble for tFAW */
|
|
unsigned char tfaw_min; /* 29 Min Four Activate Window
|
|
Delay Time*/
|
|
unsigned char opt_features; /* 30 SDRAM Optional Features */
|
|
unsigned char therm_ref_opt; /* 31 SDRAM Thermal and Refresh Opts */
|
|
unsigned char therm_sensor; /* 32 Module Thermal Sensor */
|
|
unsigned char device_type; /* 33 SDRAM device type */
|
|
int8_t fine_tck_min; /* 34 Fine offset for tCKmin */
|
|
int8_t fine_taa_min; /* 35 Fine offset for tAAmin */
|
|
int8_t fine_trcd_min; /* 36 Fine offset for tRCDmin */
|
|
int8_t fine_trp_min; /* 37 Fine offset for tRPmin */
|
|
int8_t fine_trc_min; /* 38 Fine offset for tRCmin */
|
|
unsigned char res_39_59[21]; /* 39-59 Reserved, General Section */
|
|
|
|
/* Module-Specific Section: Bytes 60-116 */
|
|
union {
|
|
struct {
|
|
/* 60 (Unbuffered) Module Nominal Height */
|
|
unsigned char mod_height;
|
|
/* 61 (Unbuffered) Module Maximum Thickness */
|
|
unsigned char mod_thickness;
|
|
/* 62 (Unbuffered) Reference Raw Card Used */
|
|
unsigned char ref_raw_card;
|
|
/* 63 (Unbuffered) Address Mapping from
|
|
Edge Connector to DRAM */
|
|
unsigned char addr_mapping;
|
|
/* 64-116 (Unbuffered) Reserved */
|
|
unsigned char res_64_116[53];
|
|
} unbuffered;
|
|
struct {
|
|
/* 60 (Registered) Module Nominal Height */
|
|
unsigned char mod_height;
|
|
/* 61 (Registered) Module Maximum Thickness */
|
|
unsigned char mod_thickness;
|
|
/* 62 (Registered) Reference Raw Card Used */
|
|
unsigned char ref_raw_card;
|
|
/* 63 DIMM Module Attributes */
|
|
unsigned char modu_attr;
|
|
/* 64 RDIMM Thermal Heat Spreader Solution */
|
|
unsigned char thermal;
|
|
/* 65 Register Manufacturer ID Code, Least Significant Byte */
|
|
unsigned char reg_id_lo;
|
|
/* 66 Register Manufacturer ID Code, Most Significant Byte */
|
|
unsigned char reg_id_hi;
|
|
/* 67 Register Revision Number */
|
|
unsigned char reg_rev;
|
|
/* 68 Register Type */
|
|
unsigned char reg_type;
|
|
/* 69-76 RC1,3,5...15 (MS Nibble) / RC0,2,4...14 (LS Nibble) */
|
|
unsigned char rcw[8];
|
|
} registered;
|
|
unsigned char uc[57]; /* 60-116 Module-Specific Section */
|
|
} mod_section;
|
|
|
|
/* Unique Module ID: Bytes 117-125 */
|
|
unsigned char mmid_lsb; /* 117 Module MfgID Code LSB - JEP-106 */
|
|
unsigned char mmid_msb; /* 118 Module MfgID Code MSB - JEP-106 */
|
|
unsigned char mloc; /* 119 Mfg Location */
|
|
unsigned char mdate[2]; /* 120-121 Mfg Date */
|
|
unsigned char sernum[4]; /* 122-125 Module Serial Number */
|
|
|
|
/* CRC: Bytes 126-127 */
|
|
unsigned char crc[2]; /* 126-127 SPD CRC */
|
|
|
|
/* Other Manufacturer Fields and User Space: Bytes 128-255 */
|
|
unsigned char mpart[18]; /* 128-145 Mfg's Module Part Number */
|
|
unsigned char mrev[2]; /* 146-147 Module Revision Code */
|
|
|
|
unsigned char dmid_lsb; /* 148 DRAM MfgID Code LSB - JEP-106 */
|
|
unsigned char dmid_msb; /* 149 DRAM MfgID Code MSB - JEP-106 */
|
|
|
|
unsigned char msd[26]; /* 150-175 Mfg's Specific Data */
|
|
unsigned char cust[80]; /* 176-255 Open for Customer Use */
|
|
|
|
} ddr3_spd_eeprom_t;
|
|
|
|
/* From JEEC Standard No. 21-C release 23A */
|
|
struct ddr4_spd_eeprom_s {
|
|
/* General Section: Bytes 0-127 */
|
|
uint8_t info_size_crc; /* 0 # bytes */
|
|
uint8_t spd_rev; /* 1 Total # bytes of SPD */
|
|
uint8_t mem_type; /* 2 Key Byte / mem type */
|
|
uint8_t module_type; /* 3 Key Byte / Module Type */
|
|
uint8_t density_banks; /* 4 Density and Banks */
|
|
uint8_t addressing; /* 5 Addressing */
|
|
uint8_t package_type; /* 6 Package type */
|
|
uint8_t opt_feature; /* 7 Optional features */
|
|
uint8_t thermal_ref; /* 8 Thermal and refresh */
|
|
uint8_t oth_opt_features; /* 9 Other optional features */
|
|
uint8_t res_10; /* 10 Reserved */
|
|
uint8_t module_vdd; /* 11 Module nominal voltage */
|
|
uint8_t organization; /* 12 Module Organization */
|
|
uint8_t bus_width; /* 13 Module Memory Bus Width */
|
|
uint8_t therm_sensor; /* 14 Module Thermal Sensor */
|
|
uint8_t ext_type; /* 15 Extended module type */
|
|
uint8_t res_16;
|
|
uint8_t timebases; /* 17 MTb and FTB */
|
|
uint8_t tck_min; /* 18 tCKAVGmin */
|
|
uint8_t tck_max; /* 19 TCKAVGmax */
|
|
uint8_t caslat_b1; /* 20 CAS latencies, 1st byte */
|
|
uint8_t caslat_b2; /* 21 CAS latencies, 2nd byte */
|
|
uint8_t caslat_b3; /* 22 CAS latencies, 3rd byte */
|
|
uint8_t caslat_b4; /* 23 CAS latencies, 4th byte */
|
|
uint8_t taa_min; /* 24 Min CAS Latency Time */
|
|
uint8_t trcd_min; /* 25 Min RAS# to CAS# Delay Time */
|
|
uint8_t trp_min; /* 26 Min Row Precharge Delay Time */
|
|
uint8_t tras_trc_ext; /* 27 Upper Nibbles for tRAS and tRC */
|
|
uint8_t tras_min_lsb; /* 28 tRASmin, lsb */
|
|
uint8_t trc_min_lsb; /* 29 tRCmin, lsb */
|
|
uint8_t trfc1_min_lsb; /* 30 Min Refresh Recovery Delay Time */
|
|
uint8_t trfc1_min_msb; /* 31 Min Refresh Recovery Delay Time */
|
|
uint8_t trfc2_min_lsb; /* 32 Min Refresh Recovery Delay Time */
|
|
uint8_t trfc2_min_msb; /* 33 Min Refresh Recovery Delay Time */
|
|
uint8_t trfc4_min_lsb; /* 34 Min Refresh Recovery Delay Time */
|
|
uint8_t trfc4_min_msb; /* 35 Min Refresh Recovery Delay Time */
|
|
uint8_t tfaw_msb; /* 36 Upper Nibble for tFAW */
|
|
uint8_t tfaw_min; /* 37 tFAW, lsb */
|
|
uint8_t trrds_min; /* 38 tRRD_Smin, MTB */
|
|
uint8_t trrdl_min; /* 39 tRRD_Lmin, MTB */
|
|
uint8_t tccdl_min; /* 40 tCCS_Lmin, MTB */
|
|
uint8_t res_41[60-41]; /* 41 Rserved */
|
|
uint8_t mapping[78-60]; /* 60~77 Connector to SDRAM bit map */
|
|
uint8_t res_78[117-78]; /* 78~116, Reserved */
|
|
int8_t fine_tccdl_min; /* 117 Fine offset for tCCD_Lmin */
|
|
int8_t fine_trrdl_min; /* 118 Fine offset for tRRD_Lmin */
|
|
int8_t fine_trrds_min; /* 119 Fine offset for tRRD_Smin */
|
|
int8_t fine_trc_min; /* 120 Fine offset for tRCmin */
|
|
int8_t fine_trp_min; /* 121 Fine offset for tRPmin */
|
|
int8_t fine_trcd_min; /* 122 Fine offset for tRCDmin */
|
|
int8_t fine_taa_min; /* 123 Fine offset for tAAmin */
|
|
int8_t fine_tck_max; /* 124 Fine offset for tCKAVGmax */
|
|
int8_t fine_tck_min; /* 125 Fine offset for tCKAVGmin */
|
|
/* CRC: Bytes 126-127 */
|
|
uint8_t crc[2]; /* 126-127 SPD CRC */
|
|
|
|
/* Module-Specific Section: Bytes 128-255 */
|
|
union {
|
|
struct {
|
|
/* 128 (Unbuffered) Module Nominal Height */
|
|
uint8_t mod_height;
|
|
/* 129 (Unbuffered) Module Maximum Thickness */
|
|
uint8_t mod_thickness;
|
|
/* 130 (Unbuffered) Reference Raw Card Used */
|
|
uint8_t ref_raw_card;
|
|
/* 131 (Unbuffered) Address Mapping from
|
|
Edge Connector to DRAM */
|
|
uint8_t addr_mapping;
|
|
/* 132~253 (Unbuffered) Reserved */
|
|
uint8_t res_132[254-132];
|
|
/* 254~255 CRC */
|
|
uint8_t crc[2];
|
|
} unbuffered;
|
|
struct {
|
|
/* 128 (Registered) Module Nominal Height */
|
|
uint8_t mod_height;
|
|
/* 129 (Registered) Module Maximum Thickness */
|
|
uint8_t mod_thickness;
|
|
/* 130 (Registered) Reference Raw Card Used */
|
|
uint8_t ref_raw_card;
|
|
/* 131 DIMM Module Attributes */
|
|
uint8_t modu_attr;
|
|
/* 132 RDIMM Thermal Heat Spreader Solution */
|
|
uint8_t thermal;
|
|
/* 133 Register Manufacturer ID Code, LSB */
|
|
uint8_t reg_id_lo;
|
|
/* 134 Register Manufacturer ID Code, MSB */
|
|
uint8_t reg_id_hi;
|
|
/* 135 Register Revision Number */
|
|
uint8_t reg_rev;
|
|
/* 136 Address mapping from register to DRAM */
|
|
uint8_t reg_map;
|
|
/* 137~253 Reserved */
|
|
uint8_t res_137[254-137];
|
|
/* 254~255 CRC */
|
|
uint8_t crc[2];
|
|
} registered;
|
|
struct {
|
|
/* 128 (Loadreduced) Module Nominal Height */
|
|
uint8_t mod_height;
|
|
/* 129 (Loadreduced) Module Maximum Thickness */
|
|
uint8_t mod_thickness;
|
|
/* 130 (Loadreduced) Reference Raw Card Used */
|
|
uint8_t ref_raw_card;
|
|
/* 131 DIMM Module Attributes */
|
|
uint8_t modu_attr;
|
|
/* 132 RDIMM Thermal Heat Spreader Solution */
|
|
uint8_t thermal;
|
|
/* 133 Register Manufacturer ID Code, LSB */
|
|
uint8_t reg_id_lo;
|
|
/* 134 Register Manufacturer ID Code, MSB */
|
|
uint8_t reg_id_hi;
|
|
/* 135 Register Revision Number */
|
|
uint8_t reg_rev;
|
|
/* 136 Address mapping from register to DRAM */
|
|
uint8_t reg_map;
|
|
/* 137 Register Output Drive Strength for CMD/Add*/
|
|
uint8_t reg_drv;
|
|
/* 138 Register Output Drive Strength for CK */
|
|
uint8_t reg_drv_ck;
|
|
/* 139 Data Buffer Revision Number */
|
|
uint8_t data_buf_rev;
|
|
/* 140 DRAM VrefDQ for Package Rank 0 */
|
|
uint8_t vrefqe_r0;
|
|
/* 141 DRAM VrefDQ for Package Rank 1 */
|
|
uint8_t vrefqe_r1;
|
|
/* 142 DRAM VrefDQ for Package Rank 2 */
|
|
uint8_t vrefqe_r2;
|
|
/* 143 DRAM VrefDQ for Package Rank 3 */
|
|
uint8_t vrefqe_r3;
|
|
/* 144 Data Buffer VrefDQ for DRAM Interface */
|
|
uint8_t data_intf;
|
|
/*
|
|
* 145 Data Buffer MDQ Drive Strength and RTT
|
|
* for data rate <= 1866
|
|
*/
|
|
uint8_t data_drv_1866;
|
|
/*
|
|
* 146 Data Buffer MDQ Drive Strength and RTT
|
|
* for 1866 < data rate <= 2400
|
|
*/
|
|
uint8_t data_drv_2400;
|
|
/*
|
|
* 147 Data Buffer MDQ Drive Strength and RTT
|
|
* for 2400 < data rate <= 3200
|
|
*/
|
|
uint8_t data_drv_3200;
|
|
/* 148 DRAM Drive Strength */
|
|
uint8_t dram_drv;
|
|
/*
|
|
* 149 DRAM ODT (RTT_WR, RTT_NOM)
|
|
* for data rate <= 1866
|
|
*/
|
|
uint8_t dram_odt_1866;
|
|
/*
|
|
* 150 DRAM ODT (RTT_WR, RTT_NOM)
|
|
* for 1866 < data rate <= 2400
|
|
*/
|
|
uint8_t dram_odt_2400;
|
|
/*
|
|
* 151 DRAM ODT (RTT_WR, RTT_NOM)
|
|
* for 2400 < data rate <= 3200
|
|
*/
|
|
uint8_t dram_odt_3200;
|
|
/*
|
|
* 152 DRAM ODT (RTT_PARK)
|
|
* for data rate <= 1866
|
|
*/
|
|
uint8_t dram_odt_park_1866;
|
|
/*
|
|
* 153 DRAM ODT (RTT_PARK)
|
|
* for 1866 < data rate <= 2400
|
|
*/
|
|
uint8_t dram_odt_park_2400;
|
|
/*
|
|
* 154 DRAM ODT (RTT_PARK)
|
|
* for 2400 < data rate <= 3200
|
|
*/
|
|
uint8_t dram_odt_park_3200;
|
|
uint8_t res_155[254-155]; /* Reserved */
|
|
/* 254~255 CRC */
|
|
uint8_t crc[2];
|
|
} loadreduced;
|
|
uint8_t uc[128]; /* 128-255 Module-Specific Section */
|
|
} mod_section;
|
|
|
|
uint8_t res_256[320-256]; /* 256~319 Reserved */
|
|
|
|
/* Module supplier's data: Byte 320~383 */
|
|
uint8_t mmid_lsb; /* 320 Module MfgID Code LSB */
|
|
uint8_t mmid_msb; /* 321 Module MfgID Code MSB */
|
|
uint8_t mloc; /* 322 Mfg Location */
|
|
uint8_t mdate[2]; /* 323~324 Mfg Date */
|
|
uint8_t sernum[4]; /* 325~328 Module Serial Number */
|
|
uint8_t mpart[20]; /* 329~348 Mfg's Module Part Number */
|
|
uint8_t mrev; /* 349 Module Revision Code */
|
|
uint8_t dmid_lsb; /* 350 DRAM MfgID Code LSB */
|
|
uint8_t dmid_msb; /* 351 DRAM MfgID Code MSB */
|
|
uint8_t stepping; /* 352 DRAM stepping */
|
|
uint8_t msd[29]; /* 353~381 Mfg's Specific Data */
|
|
uint8_t res_382[2]; /* 382~383 Reserved */
|
|
|
|
uint8_t user[512-384]; /* 384~511 End User Programmable */
|
|
};
|
|
|
|
extern unsigned int ddr1_spd_check(const ddr1_spd_eeprom_t *spd);
|
|
extern void ddr1_spd_dump(const ddr1_spd_eeprom_t *spd);
|
|
extern unsigned int ddr2_spd_check(const ddr2_spd_eeprom_t *spd);
|
|
extern void ddr2_spd_dump(const ddr2_spd_eeprom_t *spd);
|
|
extern unsigned int ddr3_spd_check(const ddr3_spd_eeprom_t *spd);
|
|
unsigned int ddr4_spd_check(const struct ddr4_spd_eeprom_s *spd);
|
|
|
|
/*
|
|
* Byte 2 Fundamental Memory Types.
|
|
*/
|
|
#define SPD_MEMTYPE_FPM (0x01)
|
|
#define SPD_MEMTYPE_EDO (0x02)
|
|
#define SPD_MEMTYPE_PIPE_NIBBLE (0x03)
|
|
#define SPD_MEMTYPE_SDRAM (0x04)
|
|
#define SPD_MEMTYPE_ROM (0x05)
|
|
#define SPD_MEMTYPE_SGRAM (0x06)
|
|
#define SPD_MEMTYPE_DDR (0x07)
|
|
#define SPD_MEMTYPE_DDR2 (0x08)
|
|
#define SPD_MEMTYPE_DDR2_FBDIMM (0x09)
|
|
#define SPD_MEMTYPE_DDR2_FBDIMM_PROBE (0x0A)
|
|
#define SPD_MEMTYPE_DDR3 (0x0B)
|
|
#define SPD_MEMTYPE_DDR4 (0x0C)
|
|
|
|
/* DIMM Type for DDR2 SPD (according to v1.3) */
|
|
#define DDR2_SPD_DIMMTYPE_UNDEFINED (0x00)
|
|
#define DDR2_SPD_DIMMTYPE_RDIMM (0x01)
|
|
#define DDR2_SPD_DIMMTYPE_UDIMM (0x02)
|
|
#define DDR2_SPD_DIMMTYPE_SO_DIMM (0x04)
|
|
#define DDR2_SPD_DIMMTYPE_72B_SO_CDIMM (0x06)
|
|
#define DDR2_SPD_DIMMTYPE_72B_SO_RDIMM (0x07)
|
|
#define DDR2_SPD_DIMMTYPE_MICRO_DIMM (0x08)
|
|
#define DDR2_SPD_DIMMTYPE_MINI_RDIMM (0x10)
|
|
#define DDR2_SPD_DIMMTYPE_MINI_UDIMM (0x20)
|
|
|
|
/* Byte 3 Key Byte / Module Type for DDR3 SPD */
|
|
#define DDR3_SPD_MODULETYPE_MASK (0x0f)
|
|
#define DDR3_SPD_MODULETYPE_RDIMM (0x01)
|
|
#define DDR3_SPD_MODULETYPE_UDIMM (0x02)
|
|
#define DDR3_SPD_MODULETYPE_SO_DIMM (0x03)
|
|
#define DDR3_SPD_MODULETYPE_MICRO_DIMM (0x04)
|
|
#define DDR3_SPD_MODULETYPE_MINI_RDIMM (0x05)
|
|
#define DDR3_SPD_MODULETYPE_MINI_UDIMM (0x06)
|
|
#define DDR3_SPD_MODULETYPE_MINI_CDIMM (0x07)
|
|
#define DDR3_SPD_MODULETYPE_72B_SO_UDIMM (0x08)
|
|
#define DDR3_SPD_MODULETYPE_72B_SO_RDIMM (0x09)
|
|
#define DDR3_SPD_MODULETYPE_72B_SO_CDIMM (0x0A)
|
|
#define DDR3_SPD_MODULETYPE_LRDIMM (0x0B)
|
|
#define DDR3_SPD_MODULETYPE_16B_SO_DIMM (0x0C)
|
|
#define DDR3_SPD_MODULETYPE_32B_SO_DIMM (0x0D)
|
|
|
|
/* DIMM Type for DDR4 SPD */
|
|
#define DDR4_SPD_MODULETYPE_MASK (0x0f)
|
|
#define DDR4_SPD_MODULETYPE_EXT (0x00)
|
|
#define DDR4_SPD_MODULETYPE_RDIMM (0x01)
|
|
#define DDR4_SPD_MODULETYPE_UDIMM (0x02)
|
|
#define DDR4_SPD_MODULETYPE_SO_DIMM (0x03)
|
|
#define DDR4_SPD_MODULETYPE_LRDIMM (0x04)
|
|
#define DDR4_SPD_MODULETYPE_MINI_RDIMM (0x05)
|
|
#define DDR4_SPD_MODULETYPE_MINI_UDIMM (0x06)
|
|
#define DDR4_SPD_MODULETYPE_72B_SO_UDIMM (0x08)
|
|
#define DDR4_SPD_MODULETYPE_72B_SO_RDIMM (0x09)
|
|
#define DDR4_SPD_MODULETYPE_16B_SO_DIMM (0x0C)
|
|
#define DDR4_SPD_MODULETYPE_32B_SO_DIMM (0x0D)
|
|
|
|
#endif /* _DDR_SPD_H_ */
|