mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-14 00:47:26 +00:00
72c46327f0
Enable dm support for USB (which also requires dm support for fixed regulators used for vbus enable) and remove usb iomux which is no longer needed. We can remove the handling of otgpwr_en gpio as this is defined in dt as usbotg vbus-supply but we need to keep the handling of USB_HUB_RST# for boards that have a USB HUB as that isn't defined in the dt's currently. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
98 lines
2.5 KiB
C
98 lines
2.5 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* Copyright (C) 2013 Gateworks Corporation
|
|
*
|
|
* Author: Tim Harvey <tharvey@gateworks.com>
|
|
*/
|
|
|
|
#ifndef _GWVENTANA_COMMON_H_
|
|
#define _GWVENTANA_COMMON_H_
|
|
|
|
#include "ventana_eeprom.h"
|
|
|
|
/* GPIO's common to all baseboards */
|
|
#define GP_PHY_RST IMX_GPIO_NR(1, 30)
|
|
#define GP_RS232_EN IMX_GPIO_NR(2, 11)
|
|
#define GP_MSATA_SEL IMX_GPIO_NR(2, 8)
|
|
|
|
#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
|
|
PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
|
|
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
|
|
|
|
#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
|
|
PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | \
|
|
PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
|
|
|
|
#define ENET_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
|
|
PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
|
|
PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
|
|
|
|
#define SPI_PAD_CTRL (PAD_CTL_HYS | \
|
|
PAD_CTL_PUS_100K_DOWN | PAD_CTL_SPEED_MED | \
|
|
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
|
|
|
|
#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
|
|
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
|
|
PAD_CTL_ODE | PAD_CTL_SRE_FAST)
|
|
|
|
#define IRQ_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
|
|
PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
|
|
PAD_CTL_DSE_34ohm | PAD_CTL_HYS | PAD_CTL_SRE_FAST)
|
|
|
|
#define DIO_PAD_CFG (MUX_PAD_CTRL(IRQ_PAD_CTRL) | MUX_MODE_SION)
|
|
|
|
#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
|
|
|
|
/*
|
|
* each baseboard has an optional set user configurable Digital IO lines which
|
|
* can be pinmuxed as a GPIO or in some cases a PWM
|
|
*/
|
|
struct dio_cfg {
|
|
iomux_v3_cfg_t gpio_padmux[2];
|
|
unsigned gpio_param;
|
|
iomux_v3_cfg_t pwm_padmux[2];
|
|
unsigned pwm_param;
|
|
};
|
|
|
|
struct ventana {
|
|
/* pinmux */
|
|
iomux_v3_cfg_t const *gpio_pads;
|
|
int num_pads;
|
|
/* DIO pinmux/val */
|
|
struct dio_cfg *dio_cfg;
|
|
int dio_num;
|
|
/* various gpios (0 if non-existent) */
|
|
int leds[3];
|
|
int pcie_rst;
|
|
int mezz_pwren;
|
|
int mezz_irq;
|
|
int rs485en;
|
|
int gps_shdn;
|
|
int vidin_en;
|
|
int dioi2c_en;
|
|
int pcie_sson;
|
|
int usb_sel;
|
|
int wdis;
|
|
int msata_en;
|
|
int rs232_en;
|
|
int vsel_pin;
|
|
int mmc_cd;
|
|
/* various features */
|
|
bool usd_vsel;
|
|
bool nand;
|
|
};
|
|
|
|
extern struct ventana gpio_cfg[GW_UNKNOWN];
|
|
|
|
/* configure i2c iomux */
|
|
void setup_ventana_i2c(int);
|
|
/* configure uart iomux */
|
|
void setup_iomux_uart(void);
|
|
/* conifgure PMIC */
|
|
void setup_pmic(void);
|
|
/* configure gpio iomux/defaults */
|
|
void setup_iomux_gpio(int board, struct ventana_board_info *);
|
|
/* late setup of GPIO (configuration per baseboard and env) */
|
|
void setup_board_gpio(int board, struct ventana_board_info *);
|
|
|
|
#endif /* #ifndef _GWVENTANA_COMMON_H_ */
|