mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-05 20:54:31 +00:00
a09fea1d28
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
103 lines
2.1 KiB
C
103 lines
2.1 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* (c) 2011 Graf-Syteco, Matthias Weisser
|
|
* <weisserm@arcor.de>
|
|
*
|
|
* Configuation settings for the zmx25 board
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
#include <asm/arch/imx-regs.h>
|
|
|
|
#define CONFIG_SYS_TIMER_RATE 32768
|
|
#define CONFIG_SYS_TIMER_COUNTER \
|
|
(&((struct gpt_regs *)IMX_GPT1_BASE)->counter)
|
|
|
|
#define CONFIG_MACH_TYPE MACH_TYPE_ZMX25
|
|
/*
|
|
* Environment settings
|
|
*/
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"gs_fast_boot=setenv bootdelay 5\0" \
|
|
"gs_slow_boot=setenv bootdelay 10\0" \
|
|
"bootcmd=dcache off; mw.l 0x81000000 0 1024; usb start;" \
|
|
"fatls usb 0; fatload usb 0 0x81000000 zmx25-init.bin;" \
|
|
"bootm 0x81000000; bootelf 0x81000000\0"
|
|
|
|
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
|
|
#define CONFIG_SETUP_MEMORY_TAGS
|
|
#define CONFIG_INITRD_TAG
|
|
|
|
/*
|
|
* Hardware drivers
|
|
*/
|
|
|
|
/*
|
|
* Serial
|
|
*/
|
|
#define CONFIG_MXC_UART
|
|
#define CONFIG_MXC_UART_BASE UART2_BASE
|
|
|
|
/*
|
|
* Ethernet
|
|
*/
|
|
#define CONFIG_FEC_MXC
|
|
#define CONFIG_FEC_MXC_PHYADDR 0x00
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
|
|
/*
|
|
* Command line configuration.
|
|
*/
|
|
|
|
/*
|
|
* Additional command
|
|
*/
|
|
|
|
/*
|
|
* USB
|
|
*/
|
|
#ifdef CONFIG_CMD_USB
|
|
#define CONFIG_USB_EHCI_MXC
|
|
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
|
|
#define CONFIG_MXC_USB_PORT 1
|
|
#define CONFIG_MXC_USB_PORTSC MXC_EHCI_MODE_SERIAL
|
|
#define CONFIG_MXC_USB_FLAGS (MXC_EHCI_INTERNAL_PHY | MXC_EHCI_IPPUE_DOWN)
|
|
#define CONFIG_EHCI_IS_TDI
|
|
#endif /* CONFIG_CMD_USB */
|
|
|
|
/* SDRAM */
|
|
#define PHYS_SDRAM 0x80000000 /* start address of LPDDRRAM */
|
|
#define PHYS_SDRAM_SIZE 0x04000000 /* 64 megs */
|
|
|
|
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
|
|
#define CONFIG_SYS_INIT_SP_ADDR 0x78020000 /* end of internal SRAM */
|
|
|
|
/*
|
|
* FLASH and environment organization
|
|
*/
|
|
#define CONFIG_SYS_FLASH_BASE 0xA0000000
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 256
|
|
|
|
/*
|
|
* CFI FLASH driver setup
|
|
*/
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE
|
|
|
|
#define CONFIG_SYS_MEMTEST_START (PHYS_SDRAM + (512*1024))
|
|
#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM + PHYS_SDRAM_SIZE)
|
|
|
|
|
|
/*
|
|
* Size of malloc() pool
|
|
*/
|
|
#define CONFIG_SYS_MALLOC_LEN (0x400000 - 0x8000)
|
|
|
|
#endif /* __CONFIG_H */
|