mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-23 11:33:32 +00:00
6e7df1d151
At this point, the remaining places where we have a symbol that is defined as CONFIG_... are in fairly odd locations. While as much dead code has been removed as possible, some of these locations are simply less obvious at first. In other cases, this code is used, but was defined in such a way as to have been missed by earlier checks. Perform a rename of all such remaining symbols to be CFG_... rather than CONFIG_... Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
129 lines
2.8 KiB
C
129 lines
2.8 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/* (C) Copyright 2019 CompuLab, Ltd. <www.compulab.co.il> */
|
|
|
|
#include <common.h>
|
|
#include <i2c.h>
|
|
#include <linux/kernel.h>
|
|
#include <asm/arch/imx8mq_pins.h>
|
|
#include <asm/mach-imx/gpio.h>
|
|
#include <asm-generic/gpio.h>
|
|
#include <asm/setup.h>
|
|
#include <linux/delay.h>
|
|
|
|
#ifdef CONFIG_SPL_BUILD
|
|
|
|
#define CFG_SYS_I2C_EEPROM_ADDR_P1 0x51
|
|
|
|
static iomux_v3_cfg_t const eeprom_pads[] = {
|
|
IMX8MQ_PAD_GPIO1_IO13__GPIO1_IO13 | MUX_PAD_CTRL(NO_PAD_CTRL),
|
|
};
|
|
|
|
#define EEPROM_WP_GPIO IMX_GPIO_NR(1, 13)
|
|
|
|
static void cl_eeprom_we(int enable)
|
|
{
|
|
static int done;
|
|
|
|
if (done) {
|
|
gpio_direction_output(EEPROM_WP_GPIO, enable);
|
|
return;
|
|
}
|
|
|
|
imx_iomux_v3_setup_multiple_pads(eeprom_pads, ARRAY_SIZE(eeprom_pads));
|
|
gpio_request(EEPROM_WP_GPIO, "eeprom_wp");
|
|
gpio_direction_output(EEPROM_WP_GPIO, enable);
|
|
done = 1;
|
|
}
|
|
|
|
static int cl_eeprom_read(uint offset, uchar *buf, int len)
|
|
{
|
|
struct udevice *dev;
|
|
int ret;
|
|
|
|
ret = i2c_get_chip_for_busnum(1, CFG_SYS_I2C_EEPROM_ADDR_P1,
|
|
CONFIG_SYS_I2C_EEPROM_ADDR_LEN, &dev);
|
|
if (ret) {
|
|
printf("%s: Cannot find EEPROM: %d\n", __func__, ret);
|
|
return ret;
|
|
}
|
|
|
|
return dm_i2c_read(dev, offset, buf, len);
|
|
}
|
|
|
|
static int cl_eeprom_write(uint offset, uchar *buf, int len)
|
|
{
|
|
struct udevice *dev;
|
|
int ret;
|
|
|
|
cl_eeprom_we(1);
|
|
|
|
ret = i2c_get_chip_for_busnum(1, CFG_SYS_I2C_EEPROM_ADDR_P1,
|
|
CONFIG_SYS_I2C_EEPROM_ADDR_LEN, &dev);
|
|
if (ret) {
|
|
printf("%s: Cannot find EEPROM: %d\n", __func__, ret);
|
|
return ret;
|
|
}
|
|
|
|
return dm_i2c_write(dev, offset, buf, len);
|
|
}
|
|
|
|
/* Reserved for fututre use area */
|
|
#define BOARD_DDRINFO_OFFSET 0x40
|
|
#define BOARD_DDR_SIZE 4
|
|
static u32 board_ddrinfo = 0xdeadbeef;
|
|
|
|
#define BOARD_DDRSUBIND_OFFSET 0x44
|
|
#define BOARD_DDRSUBIND_SIZE 1
|
|
static u8 board_ddrsubind = 0xff;
|
|
|
|
#define BOARD_OSIZE_OFFSET 0x80
|
|
#define BOARD_OSIZE_SIZE 4
|
|
static u32 board_osize = 0xdeadbeef;
|
|
|
|
#define BOARD_DDRINFO_VALID(A) ((A) != 0xdeadbeef)
|
|
|
|
u32 cl_eeprom_get_ddrinfo(void)
|
|
{
|
|
if (!BOARD_DDRINFO_VALID(board_ddrinfo)) {
|
|
if (cl_eeprom_read(BOARD_DDRINFO_OFFSET, (uchar *)&board_ddrinfo, BOARD_DDR_SIZE))
|
|
return 0;
|
|
}
|
|
return board_ddrinfo;
|
|
};
|
|
|
|
u32 cl_eeprom_set_ddrinfo(u32 ddrinfo)
|
|
{
|
|
if (cl_eeprom_write(BOARD_DDRINFO_OFFSET, (uchar *)&ddrinfo, BOARD_DDR_SIZE))
|
|
return 0;
|
|
|
|
board_ddrinfo = ddrinfo;
|
|
|
|
return board_ddrinfo;
|
|
};
|
|
|
|
u8 cl_eeprom_get_subind(void)
|
|
{
|
|
if (cl_eeprom_read(BOARD_DDRSUBIND_OFFSET, (uchar *)&board_ddrsubind, BOARD_DDRSUBIND_SIZE))
|
|
return 0xff;
|
|
|
|
return board_ddrsubind;
|
|
};
|
|
|
|
u8 cl_eeprom_set_subind(u8 ddrsubind)
|
|
{
|
|
if (cl_eeprom_write(BOARD_DDRSUBIND_OFFSET, (uchar *)&ddrsubind, BOARD_DDRSUBIND_SIZE))
|
|
return 0xff;
|
|
board_ddrsubind = ddrsubind;
|
|
|
|
return board_ddrsubind;
|
|
};
|
|
|
|
/* override-size ifaces */
|
|
u32 cl_eeprom_get_osize(void)
|
|
{
|
|
if (cl_eeprom_read(BOARD_OSIZE_OFFSET, (uchar *)&board_osize, BOARD_OSIZE_SIZE))
|
|
return 0;
|
|
|
|
return board_osize;
|
|
};
|
|
#endif
|