u-boot/include/configs/gplugd.h
Tom Rini a09fea1d28 env: Finish migration of common ENV options
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00

79 lines
1.9 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2011
* eInfochips Ltd. <www.einfochips.com>
* Written-by: Ajay Bhargav <contact@8051projects.net>
*
* Based on Aspenite:
* (C) Copyright 2010
* Marvell Semiconductor <www.marvell.com>
* Written-by: Prafulla Wadaskar <prafulla@marvell.com>
* Contributor: Mahavir Jain <mjain@marvell.com>
*/
#ifndef __CONFIG_GPLUGD_H
#define __CONFIG_GPLUGD_H
/*
* High Level Configuration Options
*/
#define CONFIG_SHEEVA_88SV331xV5 1 /* CPU Core subversion */
#define CONFIG_ARMADA100 1 /* SOC Family Name */
#define CONFIG_ARMADA168 1 /* SOC Used on this Board */
#define CONFIG_MACH_TYPE MACH_TYPE_GPLUGD /* Machine type */
#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
/*
* There is no internal RAM in ARMADA100, using DRAM
* TBD: dcache to be used for this
*/
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_TEXT_BASE - 0x00200000)
/*
* Commands configuration
*/
/* Network configuration */
#ifdef CONFIG_CMD_NET
#define CONFIG_ARMADA100_FEC
/* DHCP Support */
#define CONFIG_BOOTP_DHCP_REQUEST_DELAY 50000
#endif /* CONFIG_CMD_NET */
/* GPIO Support */
#define CONFIG_MARVELL_GPIO
/* PHY configuration */
#define CONFIG_RESET_PHY_R
/* 88E3015 register definition */
#define PHY_LED_PAR_SEL_REG 22
#define PHY_LED_MAN_REG 25
#define PHY_LED_VAL 0x5b /* LINK LED1, ACT LED2 */
/* GPIO Configuration for PHY */
#define CONFIG_SYS_GPIO_PHY_RST 104 /* GPIO104 */
/* Flash Support */
/*
* mv-common.h should be defined after CMD configs since it used them
* to enable certain macros
*/
#include "mv-common.h"
#ifdef CONFIG_SYS_NS16550_COM1
#undef CONFIG_SYS_NS16550_COM1
#endif /* CONFIG_SYS_NS16550_COM1 */
#define CONFIG_SYS_NS16550_COM1 ARMD1_UART3_BASE
/*
* Environment variables configurations
*/
#ifdef CONFIG_CMD_USB
#define CONFIG_USB_EHCI_ARMADA100
#define CONFIG_EHCI_IS_TDI
#endif /* CONFIG_CMD_USB */
#endif /* __CONFIG_GPLUGD_H */