mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-13 23:02:59 +00:00
1a4596601f
Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
108 lines
2.4 KiB
C
108 lines
2.4 KiB
C
/*
|
|
* (C) Copyright 2009
|
|
* Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com.
|
|
*
|
|
* Copyright (C) 2012 Stefan Roese <sr@denx.de>
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <nand.h>
|
|
#include <netdev.h>
|
|
#include <phy.h>
|
|
#include <rtc.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/hardware.h>
|
|
#include <asm/arch/spr_defs.h>
|
|
#include <asm/arch/spr_misc.h>
|
|
#include <linux/mtd/fsmc_nand.h>
|
|
#include "fpga.h"
|
|
|
|
static struct nand_chip nand_chip[CONFIG_SYS_MAX_NAND_DEVICE];
|
|
|
|
int board_init(void)
|
|
{
|
|
/*
|
|
* X600 is equipped with an M41T82 RTC. This RTC has the
|
|
* HT bit (Halt Update), which needs to be cleared upon
|
|
* power-up. Otherwise the RTC is halted.
|
|
*/
|
|
rtc_reset();
|
|
|
|
return spear_board_init(MACH_TYPE_SPEAR600);
|
|
}
|
|
|
|
int board_late_init(void)
|
|
{
|
|
/*
|
|
* Monitor and env protection on by default
|
|
*/
|
|
flash_protect(FLAG_PROTECT_SET,
|
|
CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE +
|
|
CONFIG_SYS_SPL_LEN + CONFIG_SYS_MONITOR_LEN +
|
|
2 * CONFIG_ENV_SECT_SIZE - 1,
|
|
&flash_info[0]);
|
|
|
|
/* Init FPGA subsystem */
|
|
x600_init_fpga();
|
|
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* board_nand_init - Board specific NAND initialization
|
|
* @nand: mtd private chip structure
|
|
*
|
|
* Called by nand_init_chip to initialize the board specific functions
|
|
*/
|
|
|
|
void board_nand_init(void)
|
|
{
|
|
struct misc_regs *const misc_regs_p =
|
|
(struct misc_regs *)CONFIG_SPEAR_MISCBASE;
|
|
struct nand_chip *nand = &nand_chip[0];
|
|
|
|
if (!(readl(&misc_regs_p->auto_cfg_reg) & MISC_NANDDIS))
|
|
fsmc_nand_init(nand);
|
|
}
|
|
|
|
int designware_board_phy_init(struct eth_device *dev, int phy_addr,
|
|
int (*mii_write)(struct eth_device *, u8, u8, u16),
|
|
int dw_reset_phy(struct eth_device *))
|
|
{
|
|
/* Extended PHY control 1, select GMII */
|
|
mii_write(dev, phy_addr, 23, 0x0020);
|
|
|
|
/* Software reset necessary after GMII mode selction */
|
|
dw_reset_phy(dev);
|
|
|
|
/* Enable extended page register access */
|
|
mii_write(dev, phy_addr, 31, 0x0001);
|
|
|
|
/* 17e: Enhanced LED behavior, needs to be written twice */
|
|
mii_write(dev, phy_addr, 17, 0x09ff);
|
|
mii_write(dev, phy_addr, 17, 0x09ff);
|
|
|
|
/* 16e: Enhanced LED method select */
|
|
mii_write(dev, phy_addr, 16, 0xe0ea);
|
|
|
|
/* Disable extended page register access */
|
|
mii_write(dev, phy_addr, 31, 0x0000);
|
|
|
|
/* Enable clock output pin */
|
|
mii_write(dev, phy_addr, 18, 0x0049);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_eth_init(bd_t *bis)
|
|
{
|
|
int ret = 0;
|
|
|
|
if (designware_initialize(0, CONFIG_SPEAR_ETHBASE, CONFIG_PHY_ADDR,
|
|
PHY_INTERFACE_MODE_GMII) >= 0)
|
|
ret++;
|
|
|
|
return ret;
|
|
}
|