u-boot/board/keymile/km83xx/km83xx.c
Simon Glass e895a4b06f fdt: Allow ft_board_setup() to report failure
This function can fail if the device tree runs out of space. Rather than
silently booting with an incomplete device tree, allow the failure to be
detected.

Unfortunately this involves changing a lot of places in the code. I have
not changed behvaiour to return an error where one is not currently
returned, to avoid unexpected breakage.

Eventually it would be nice to allow boards to register functions to be
called to update the device tree. This would avoid all the many functions
to do this. However it's not clear yet if this should be done using driver
model or with a linker list. This work is left for later.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
2014-11-21 04:43:15 +01:00

412 lines
11 KiB
C

/*
* Copyright (C) 2006 Freescale Semiconductor, Inc.
* Dave Liu <daveliu@freescale.com>
*
* Copyright (C) 2007 Logic Product Development, Inc.
* Peter Barada <peterb@logicpd.com>
*
* Copyright (C) 2007 MontaVista Software, Inc.
* Anton Vorontsov <avorontsov@ru.mvista.com>
*
* (C) Copyright 2008 - 2010
* Heiko Schocher, DENX Software Engineering, hs@denx.de.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <ioports.h>
#include <mpc83xx.h>
#include <i2c.h>
#include <miiphy.h>
#include <asm/io.h>
#include <asm/mmu.h>
#include <asm/processor.h>
#include <pci.h>
#include <libfdt.h>
#include <post.h>
#include "../common/common.h"
const qe_iop_conf_t qe_iop_conf_tab[] = {
/* port pin dir open_drain assign */
#if defined(CONFIG_MPC8360)
/* MDIO */
{0, 1, 3, 0, 2}, /* MDIO */
{0, 2, 1, 0, 1}, /* MDC */
/* UCC4 - UEC */
{1, 14, 1, 0, 1}, /* TxD0 */
{1, 15, 1, 0, 1}, /* TxD1 */
{1, 20, 2, 0, 1}, /* RxD0 */
{1, 21, 2, 0, 1}, /* RxD1 */
{1, 18, 1, 0, 1}, /* TX_EN */
{1, 26, 2, 0, 1}, /* RX_DV */
{1, 27, 2, 0, 1}, /* RX_ER */
{1, 24, 2, 0, 1}, /* COL */
{1, 25, 2, 0, 1}, /* CRS */
{2, 15, 2, 0, 1}, /* TX_CLK - CLK16 */
{2, 16, 2, 0, 1}, /* RX_CLK - CLK17 */
/* DUART - UART2 */
{5, 0, 1, 0, 2}, /* UART2_SOUT */
{5, 2, 1, 0, 1}, /* UART2_RTS */
{5, 3, 2, 0, 2}, /* UART2_SIN */
{5, 1, 2, 0, 3}, /* UART2_CTS */
#elif !defined(CONFIG_MPC8309)
/* Local Bus */
{0, 16, 1, 0, 3}, /* LA00 */
{0, 17, 1, 0, 3}, /* LA01 */
{0, 18, 1, 0, 3}, /* LA02 */
{0, 19, 1, 0, 3}, /* LA03 */
{0, 20, 1, 0, 3}, /* LA04 */
{0, 21, 1, 0, 3}, /* LA05 */
{0, 22, 1, 0, 3}, /* LA06 */
{0, 23, 1, 0, 3}, /* LA07 */
{0, 24, 1, 0, 3}, /* LA08 */
{0, 25, 1, 0, 3}, /* LA09 */
{0, 26, 1, 0, 3}, /* LA10 */
{0, 27, 1, 0, 3}, /* LA11 */
{0, 28, 1, 0, 3}, /* LA12 */
{0, 29, 1, 0, 3}, /* LA13 */
{0, 30, 1, 0, 3}, /* LA14 */
{0, 31, 1, 0, 3}, /* LA15 */
/* MDIO */
{3, 4, 3, 0, 2}, /* MDIO */
{3, 5, 1, 0, 2}, /* MDC */
/* UCC4 - UEC */
{1, 18, 1, 0, 1}, /* TxD0 */
{1, 19, 1, 0, 1}, /* TxD1 */
{1, 22, 2, 0, 1}, /* RxD0 */
{1, 23, 2, 0, 1}, /* RxD1 */
{1, 26, 2, 0, 1}, /* RxER */
{1, 28, 2, 0, 1}, /* Rx_DV */
{1, 30, 1, 0, 1}, /* TxEN */
{1, 31, 2, 0, 1}, /* CRS */
{3, 10, 2, 0, 3}, /* TxCLK->CLK17 */
#endif
/* END of table */
{0, 0, 0, 0, QE_IOP_TAB_END},
};
#if defined(CONFIG_SUVD3)
const uint upma_table[] = {
0x1ffedc00, 0x0ffcdc80, 0x0ffcdc80, 0x0ffcdc04, /* Words 0 to 3 */
0x0ffcdc00, 0xffffcc00, 0xffffcc01, 0xfffffc01, /* Words 4 to 7 */
0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 8 to 11 */
0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 12 to 15 */
0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 16 to 19 */
0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 20 to 23 */
0x9cfffc00, 0x00fffc80, 0x00fffc80, 0x00fffc00, /* Words 24 to 27 */
0xffffec04, 0xffffec01, 0xfffffc01, 0xfffffc01, /* Words 28 to 31 */
0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 32 to 35 */
0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 36 to 39 */
0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 40 to 43 */
0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 44 to 47 */
0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 48 to 51 */
0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 52 to 55 */
0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01, /* Words 56 to 59 */
0xfffffc01, 0xfffffc01, 0xfffffc01, 0xfffffc01 /* Words 60 to 63 */
};
#endif
static int piggy_present(void)
{
struct km_bec_fpga __iomem *base =
(struct km_bec_fpga __iomem *)CONFIG_SYS_KMBEC_FPGA_BASE;
return in_8(&base->bprth) & PIGGY_PRESENT;
}
#if defined(CONFIG_KMVECT1)
int ethernet_present(void)
{
/* ethernet port connected to simple switch without piggy */
return 1;
}
#else
int ethernet_present(void)
{
return piggy_present();
}
#endif
int board_early_init_r(void)
{
struct km_bec_fpga *base =
(struct km_bec_fpga *)CONFIG_SYS_KMBEC_FPGA_BASE;
#if defined(CONFIG_SUVD3)
immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
fsl_lbc_t *lbc = &immap->im_lbc;
u32 *mxmr = &lbc->mamr;
#endif
#if defined(CONFIG_MPC8360)
unsigned short svid;
/*
* Because of errata in the UCCs, we have to write to the reserved
* registers to slow the clocks down.
*/
svid = SVR_REV(mfspr(SVR));
switch (svid) {
case 0x0020:
/*
* MPC8360ECE.pdf QE_ENET10 table 4:
* IMMR + 0x14A8[4:5] = 11 (clk delay for UCC 2)
* IMMR + 0x14A8[18:19] = 11 (clk delay for UCC 1)
*/
setbits_be32((void *)(CONFIG_SYS_IMMR + 0x14a8), 0x0c003000);
break;
case 0x0021:
/*
* MPC8360ECE.pdf QE_ENET10 table 4:
* IMMR + 0x14AC[24:27] = 1010
*/
clrsetbits_be32((void *)(CONFIG_SYS_IMMR + 0x14ac),
0x00000050, 0x000000a0);
break;
}
#endif
/* enable the PHY on the PIGGY */
setbits_8(&base->pgy_eth, 0x01);
/* enable the Unit LED (green) */
setbits_8(&base->oprth, WRL_BOOT);
/* enable Application Buffer */
setbits_8(&base->oprtl, OPRTL_XBUFENA);
#if defined(CONFIG_SUVD3)
/* configure UPMA for APP1 */
upmconfig(UPMA, (uint *) upma_table,
sizeof(upma_table) / sizeof(uint));
out_be32(mxmr, CONFIG_SYS_MAMR);
#endif
return 0;
}
int misc_init_r(void)
{
return 0;
}
#if defined(CONFIG_KMVECT1)
#include <mv88e6352.h>
/* Marvell MV88E6122 switch configuration */
static struct mv88e_sw_reg extsw_conf[] = {
/* port 1, FRONT_MDI, autoneg */
{ PORT(1), PORT_PHY, NO_SPEED_FOR },
{ PORT(1), PORT_CTRL, FORWARDING | EGRS_FLD_ALL },
{ PHY(1), PHY_1000_CTRL, NO_ADV },
{ PHY(1), PHY_SPEC_CTRL, AUTO_MDIX_EN },
{ PHY(1), PHY_CTRL, PHY_100_MBPS | AUTONEG_EN | AUTONEG_RST |
FULL_DUPLEX },
/* port 2, unused */
{ PORT(2), PORT_CTRL, PORT_DIS },
{ PHY(2), PHY_CTRL, PHY_PWR_DOWN },
{ PHY(2), PHY_SPEC_CTRL, SPEC_PWR_DOWN },
/* port 3, BP_MII (CPU), PHY mode, 100BASE */
{ PORT(3), PORT_CTRL, FORWARDING | EGRS_FLD_ALL },
/* port 4, ESTAR to slot 11, SerDes, 1000BASE-X */
{ PORT(4), PORT_STATUS, NO_PHY_DETECT },
{ PORT(4), PORT_PHY, SPEED_1000_FOR },
{ PORT(4), PORT_CTRL, FORWARDING | EGRS_FLD_ALL },
/* port 5, ESTAR to slot 13, SerDes, 1000BASE-X */
{ PORT(5), PORT_STATUS, NO_PHY_DETECT },
{ PORT(5), PORT_PHY, SPEED_1000_FOR },
{ PORT(5), PORT_CTRL, FORWARDING | EGRS_FLD_ALL },
/*
* Errata Fix: 1.9V Output from Internal 1.8V Regulator,
* acc . MV-S300889-00D.pdf , clause 4.5
*/
{ PORT(5), 0x1A, 0xADB1 },
/* port 6, unused, this port has no phy */
{ PORT(6), PORT_CTRL, PORT_DIS },
/*
* Errata Fix: 1.9V Output from Internal 1.8V Regulator,
* acc . MV-S300889-00D.pdf , clause 4.5
*/
{ PORT(5), 0x1A, 0xADB1 },
};
#endif
int last_stage_init(void)
{
#if defined(CONFIG_KMVECT1)
struct km_bec_fpga __iomem *base =
(struct km_bec_fpga __iomem *)CONFIG_SYS_KMBEC_FPGA_BASE;
u8 tmp_reg;
/* Release mv88e6122 from reset */
tmp_reg = in_8(&base->res1[0]) | 0x10; /* DIRECT3 register */
out_8(&base->res1[0], tmp_reg); /* GP28 as output */
tmp_reg = in_8(&base->gprt3) | 0x10; /* GP28 to high */
out_8(&base->gprt3, tmp_reg);
/* configure MV88E6122 switch */
char *name = "UEC2";
if (miiphy_set_current_dev(name))
return 0;
mv88e_sw_program(name, CONFIG_KM_MVEXTSW_ADDR, extsw_conf,
ARRAY_SIZE(extsw_conf));
mv88e_sw_reset(name, CONFIG_KM_MVEXTSW_ADDR);
if (piggy_present()) {
setenv("ethact", "UEC2");
setenv("netdev", "eth1");
puts("using PIGGY for network boot\n");
} else {
setenv("netdev", "eth0");
puts("using frontport for network boot\n");
}
#endif
#if defined(CONFIG_KMCOGE5NE)
struct bfticu_iomap *base =
(struct bfticu_iomap *)CONFIG_SYS_BFTIC3_BASE;
u8 dip_switch = in_8((u8 *)&(base->mswitch)) & BFTICU_DIPSWITCH_MASK;
if (dip_switch != 0) {
/* start bootloader */
puts("DIP: Enabled\n");
setenv("actual_bank", "0");
}
#endif
set_km_env();
return 0;
}
static int fixed_sdram(void)
{
immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
u32 msize = 0;
u32 ddr_size;
u32 ddr_size_log2;
out_be32(&im->sysconf.ddrlaw[0].ar, (LAWAR_EN | 0x1e));
out_be32(&im->ddr.csbnds[0].csbnds, (CONFIG_SYS_DDR_CS0_BNDS) | 0x7f);
out_be32(&im->ddr.cs_config[0], CONFIG_SYS_DDR_CS0_CONFIG);
out_be32(&im->ddr.timing_cfg_0, CONFIG_SYS_DDR_TIMING_0);
out_be32(&im->ddr.timing_cfg_1, CONFIG_SYS_DDR_TIMING_1);
out_be32(&im->ddr.timing_cfg_2, CONFIG_SYS_DDR_TIMING_2);
out_be32(&im->ddr.timing_cfg_3, CONFIG_SYS_DDR_TIMING_3);
out_be32(&im->ddr.sdram_cfg, CONFIG_SYS_DDR_SDRAM_CFG);
out_be32(&im->ddr.sdram_cfg2, CONFIG_SYS_DDR_SDRAM_CFG2);
out_be32(&im->ddr.sdram_mode, CONFIG_SYS_DDR_MODE);
out_be32(&im->ddr.sdram_mode2, CONFIG_SYS_DDR_MODE2);
out_be32(&im->ddr.sdram_interval, CONFIG_SYS_DDR_INTERVAL);
out_be32(&im->ddr.sdram_clk_cntl, CONFIG_SYS_DDR_CLK_CNTL);
udelay(200);
setbits_be32(&im->ddr.sdram_cfg, SDRAM_CFG_MEM_EN);
msize = CONFIG_SYS_DDR_SIZE << 20;
disable_addr_trans();
msize = get_ram_size(CONFIG_SYS_DDR_BASE, msize);
enable_addr_trans();
msize /= (1024 * 1024);
if (CONFIG_SYS_DDR_SIZE != msize) {
for (ddr_size = msize << 20, ddr_size_log2 = 0;
(ddr_size > 1);
ddr_size = ddr_size >> 1, ddr_size_log2++)
if (ddr_size & 1)
return -1;
out_be32(&im->sysconf.ddrlaw[0].ar,
(LAWAR_EN | ((ddr_size_log2 - 1) & LAWAR_SIZE)));
out_be32(&im->ddr.csbnds[0].csbnds,
(((msize / 16) - 1) & 0xff));
}
return msize;
}
phys_size_t initdram(int board_type)
{
immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
u32 msize = 0;
if ((in_be32(&im->sysconf.immrbar) & IMMRBAR_BASE_ADDR) != (u32)im)
return -1;
out_be32(&im->sysconf.ddrlaw[0].bar,
CONFIG_SYS_DDR_BASE & LAWBAR_BAR);
msize = fixed_sdram();
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
/*
* Initialize DDR ECC byte
*/
ddr_enable_ecc(msize * 1024 * 1024);
#endif
/* return total bus SDRAM size(bytes) -- DDR */
return msize * 1024 * 1024;
}
int checkboard(void)
{
puts("Board: Keymile " CONFIG_KM_BOARD_NAME);
if (piggy_present())
puts(" with PIGGY.");
puts("\n");
return 0;
}
#if defined(CONFIG_OF_BOARD_SETUP)
int ft_board_setup(void *blob, bd_t *bd)
{
ft_cpu_setup(blob, bd);
return 0;
}
#endif
#if defined(CONFIG_HUSH_INIT_VAR)
int hush_init_var(void)
{
ivm_read_eeprom();
return 0;
}
#endif
#if defined(CONFIG_POST)
int post_hotkeys_pressed(void)
{
int testpin = 0;
struct km_bec_fpga *base =
(struct km_bec_fpga *)CONFIG_SYS_KMBEC_FPGA_BASE;
int testpin_reg = in_8(&base->CONFIG_TESTPIN_REG);
testpin = (testpin_reg & CONFIG_TESTPIN_MASK) != 0;
debug("post_hotkeys_pressed: %d\n", !testpin);
return testpin;
}
ulong post_word_load(void)
{
void* addr = (ulong *) (CPM_POST_WORD_ADDR);
debug("post_word_load 0x%08lX: 0x%08X\n", (ulong)addr, in_le32(addr));
return in_le32(addr);
}
void post_word_store(ulong value)
{
void* addr = (ulong *) (CPM_POST_WORD_ADDR);
debug("post_word_store 0x%08lX: 0x%08lX\n", (ulong)addr, value);
out_le32(addr, value);
}
int arch_memory_test_prepare(u32 *vstart, u32 *size, phys_addr_t *phys_offset)
{
*vstart = CONFIG_SYS_MEMTEST_START;
*size = CONFIG_SYS_MEMTEST_END - CONFIG_SYS_MEMTEST_START;
debug("arch_memory_test_prepare 0x%08X 0x%08X\n", *vstart, *size);
return 0;
}
#endif