mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-09-27 09:52:18 +00:00
52caf2c12b
It is not recommended to have aliases for gpio. In past it was used in Linux for assigning numbers via sysfs which is deprecated and libgpiod should be used instead. In U-Boot this number is used for seq number but gpio offset are not counted from this number. That's why having these aliases only for seq number is not needed. As is done in Linux it is the best to use full gpio name instead of sequence number which depends on sequence in binding. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
553 lines
9.8 KiB
Text
553 lines
9.8 KiB
Text
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* dts file for Xilinx ZynqMP ZCU104
|
|
*
|
|
* (C) Copyright 2017 - 2021, Xilinx, Inc.
|
|
*
|
|
* Michal Simek <michal.simek@xilinx.com>
|
|
*/
|
|
|
|
/dts-v1/;
|
|
|
|
#include "zynqmp.dtsi"
|
|
#include "zynqmp-clk-ccf.dtsi"
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
|
|
#include <dt-bindings/phy/phy.h>
|
|
|
|
/ {
|
|
model = "ZynqMP ZCU104 RevC";
|
|
compatible = "xlnx,zynqmp-zcu104-revC", "xlnx,zynqmp-zcu104", "xlnx,zynqmp";
|
|
|
|
aliases {
|
|
ethernet0 = &gem3;
|
|
i2c0 = &i2c1;
|
|
mmc0 = &sdhci1;
|
|
nvmem0 = &eeprom;
|
|
rtc0 = &rtc;
|
|
serial0 = &uart0;
|
|
serial1 = &uart1;
|
|
serial2 = &dcc;
|
|
spi0 = &qspi;
|
|
usb0 = &usb0;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "earlycon";
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
|
|
memory@0 {
|
|
device_type = "memory";
|
|
reg = <0x0 0x0 0x0 0x80000000>;
|
|
};
|
|
|
|
ina226 {
|
|
compatible = "iio-hwmon";
|
|
io-channels = <&u183 0>, <&u183 1>, <&u183 2>, <&u183 3>;
|
|
};
|
|
|
|
clock_8t49n287_5: clk125 {
|
|
compatible = "fixed-clock";
|
|
#clock-cells = <0>;
|
|
clock-frequency = <125000000>;
|
|
};
|
|
|
|
clock_8t49n287_2: clk26 {
|
|
compatible = "fixed-clock";
|
|
#clock-cells = <0>;
|
|
clock-frequency = <26000000>;
|
|
};
|
|
|
|
clock_8t49n287_3: clk27 {
|
|
compatible = "fixed-clock";
|
|
#clock-cells = <0>;
|
|
clock-frequency = <27000000>;
|
|
};
|
|
};
|
|
|
|
&can1 {
|
|
status = "okay";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_can1_default>;
|
|
};
|
|
|
|
&dcc {
|
|
status = "okay";
|
|
};
|
|
|
|
&fpd_dma_chan1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&fpd_dma_chan2 {
|
|
status = "okay";
|
|
};
|
|
|
|
&fpd_dma_chan3 {
|
|
status = "okay";
|
|
};
|
|
|
|
&fpd_dma_chan4 {
|
|
status = "okay";
|
|
};
|
|
|
|
&fpd_dma_chan5 {
|
|
status = "okay";
|
|
};
|
|
|
|
&fpd_dma_chan6 {
|
|
status = "okay";
|
|
};
|
|
|
|
&fpd_dma_chan7 {
|
|
status = "okay";
|
|
};
|
|
|
|
&fpd_dma_chan8 {
|
|
status = "okay";
|
|
};
|
|
|
|
&gem3 {
|
|
status = "okay";
|
|
phy-handle = <&phy0>;
|
|
phy-mode = "rgmii-id";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_gem3_default>;
|
|
phy0: ethernet-phy@c {
|
|
reg = <0xc>;
|
|
ti,rx-internal-delay = <0x8>;
|
|
ti,tx-internal-delay = <0xa>;
|
|
ti,fifo-depth = <0x1>;
|
|
ti,dp83867-rxctrl-strap-quirk;
|
|
};
|
|
};
|
|
|
|
&gpio {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpu {
|
|
status = "okay";
|
|
};
|
|
|
|
&i2c1 {
|
|
status = "okay";
|
|
clock-frequency = <400000>;
|
|
pinctrl-names = "default", "gpio";
|
|
pinctrl-0 = <&pinctrl_i2c1_default>;
|
|
pinctrl-1 = <&pinctrl_i2c1_gpio>;
|
|
scl-gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
|
|
sda-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
|
|
|
|
tca6416_u97: gpio@20 {
|
|
compatible = "ti,tca6416";
|
|
reg = <0x20>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
/*
|
|
* IRQ not connected
|
|
* Lines:
|
|
* 0 - IRPS5401_ALERT_B
|
|
* 1 - HDMI_8T49N241_INT_ALM
|
|
* 2 - MAX6643_OT_B
|
|
* 3 - MAX6643_FANFAIL_B
|
|
* 5 - IIC_MUX_RESET_B
|
|
* 6 - GEM3_EXP_RESET_B
|
|
* 7 - FMC_LPC_PRSNT_M2C_B
|
|
* 4, 10 - 17 - not connected
|
|
*/
|
|
};
|
|
|
|
/* Another connection to this bus via PL i2c via PCA9306 - u45 */
|
|
i2c-mux@74 { /* u34 */
|
|
compatible = "nxp,pca9548";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <0x74>;
|
|
i2c@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <0>;
|
|
/*
|
|
* IIC_EEPROM 1kB memory which uses 256B blocks
|
|
* where every block has different address.
|
|
* 0 - 256B address 0x54
|
|
* 256B - 512B address 0x55
|
|
* 512B - 768B address 0x56
|
|
* 768B - 1024B address 0x57
|
|
*/
|
|
eeprom: eeprom@54 { /* u23 */
|
|
compatible = "atmel,24c08";
|
|
reg = <0x54>;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
};
|
|
};
|
|
|
|
i2c@1 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <1>;
|
|
/* 8T49N287 - u182 */
|
|
};
|
|
|
|
i2c@2 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <2>;
|
|
irps5401_43: irps5401@43 { /* IRPS5401 - u175 */
|
|
compatible = "infineon,irps5401";
|
|
reg = <0x43>; /* pmbus / i2c 0x13 */
|
|
};
|
|
irps5401_44: irps5401@44 { /* IRPS5401 - u180 */
|
|
compatible = "infineon,irps5401";
|
|
reg = <0x44>; /* pmbus / i2c 0x14 */
|
|
};
|
|
};
|
|
|
|
i2c@3 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <3>;
|
|
u183: ina226@40 { /* u183 */
|
|
compatible = "ti,ina226";
|
|
#io-channel-cells = <1>;
|
|
reg = <0x40>;
|
|
shunt-resistor = <5000>;
|
|
};
|
|
};
|
|
|
|
i2c@5 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <5>;
|
|
};
|
|
|
|
i2c@7 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <7>;
|
|
};
|
|
|
|
/* 4, 6 not connected */
|
|
};
|
|
};
|
|
|
|
&pinctrl0 {
|
|
status = "okay";
|
|
|
|
pinctrl_can1_default: can1-default {
|
|
mux {
|
|
function = "can1";
|
|
groups = "can1_6_grp";
|
|
};
|
|
|
|
conf {
|
|
groups = "can1_6_grp";
|
|
slew-rate = <SLEW_RATE_SLOW>;
|
|
power-source = <IO_STANDARD_LVCMOS18>;
|
|
drive-strength = <12>;
|
|
};
|
|
|
|
conf-rx {
|
|
pins = "MIO25";
|
|
bias-high-impedance;
|
|
};
|
|
|
|
conf-tx {
|
|
pins = "MIO24";
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
pinctrl_i2c1_default: i2c1-default {
|
|
mux {
|
|
groups = "i2c1_4_grp";
|
|
function = "i2c1";
|
|
};
|
|
|
|
conf {
|
|
groups = "i2c1_4_grp";
|
|
bias-pull-up;
|
|
slew-rate = <SLEW_RATE_SLOW>;
|
|
power-source = <IO_STANDARD_LVCMOS18>;
|
|
drive-strength = <12>;
|
|
};
|
|
};
|
|
|
|
pinctrl_i2c1_gpio: i2c1-gpio {
|
|
mux {
|
|
groups = "gpio0_16_grp", "gpio0_17_grp";
|
|
function = "gpio0";
|
|
};
|
|
|
|
conf {
|
|
groups = "gpio0_16_grp", "gpio0_17_grp";
|
|
slew-rate = <SLEW_RATE_SLOW>;
|
|
power-source = <IO_STANDARD_LVCMOS18>;
|
|
drive-strength = <12>;
|
|
};
|
|
};
|
|
|
|
pinctrl_gem3_default: gem3-default {
|
|
mux {
|
|
function = "ethernet3";
|
|
groups = "ethernet3_0_grp";
|
|
};
|
|
|
|
conf {
|
|
groups = "ethernet3_0_grp";
|
|
slew-rate = <SLEW_RATE_SLOW>;
|
|
power-source = <IO_STANDARD_LVCMOS18>;
|
|
drive-strength = <12>;
|
|
};
|
|
|
|
conf-rx {
|
|
pins = "MIO70", "MIO71", "MIO72", "MIO73", "MIO74",
|
|
"MIO75";
|
|
bias-high-impedance;
|
|
low-power-disable;
|
|
};
|
|
|
|
conf-tx {
|
|
pins = "MIO64", "MIO65", "MIO66", "MIO67", "MIO68",
|
|
"MIO69";
|
|
bias-disable;
|
|
low-power-enable;
|
|
};
|
|
|
|
mux-mdio {
|
|
function = "mdio3";
|
|
groups = "mdio3_0_grp";
|
|
};
|
|
|
|
conf-mdio {
|
|
groups = "mdio3_0_grp";
|
|
slew-rate = <SLEW_RATE_SLOW>;
|
|
power-source = <IO_STANDARD_LVCMOS18>;
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
pinctrl_sdhci1_default: sdhci1-default {
|
|
mux {
|
|
groups = "sdio1_0_grp";
|
|
function = "sdio1";
|
|
};
|
|
|
|
conf {
|
|
groups = "sdio1_0_grp";
|
|
slew-rate = <SLEW_RATE_SLOW>;
|
|
power-source = <IO_STANDARD_LVCMOS18>;
|
|
bias-disable;
|
|
drive-strength = <12>;
|
|
};
|
|
|
|
mux-cd {
|
|
groups = "sdio1_cd_0_grp";
|
|
function = "sdio1_cd";
|
|
};
|
|
|
|
conf-cd {
|
|
groups = "sdio1_cd_0_grp";
|
|
bias-high-impedance;
|
|
bias-pull-up;
|
|
slew-rate = <SLEW_RATE_SLOW>;
|
|
power-source = <IO_STANDARD_LVCMOS18>;
|
|
};
|
|
};
|
|
|
|
pinctrl_uart0_default: uart0-default {
|
|
mux {
|
|
groups = "uart0_4_grp";
|
|
function = "uart0";
|
|
};
|
|
|
|
conf {
|
|
groups = "uart0_4_grp";
|
|
slew-rate = <SLEW_RATE_SLOW>;
|
|
power-source = <IO_STANDARD_LVCMOS18>;
|
|
drive-strength = <12>;
|
|
};
|
|
|
|
conf-rx {
|
|
pins = "MIO18";
|
|
bias-high-impedance;
|
|
};
|
|
|
|
conf-tx {
|
|
pins = "MIO19";
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
pinctrl_uart1_default: uart1-default {
|
|
mux {
|
|
groups = "uart1_5_grp";
|
|
function = "uart1";
|
|
};
|
|
|
|
conf {
|
|
groups = "uart1_5_grp";
|
|
slew-rate = <SLEW_RATE_SLOW>;
|
|
power-source = <IO_STANDARD_LVCMOS18>;
|
|
drive-strength = <12>;
|
|
};
|
|
|
|
conf-rx {
|
|
pins = "MIO21";
|
|
bias-high-impedance;
|
|
};
|
|
|
|
conf-tx {
|
|
pins = "MIO20";
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
pinctrl_usb0_default: usb0-default {
|
|
mux {
|
|
groups = "usb0_0_grp";
|
|
function = "usb0";
|
|
};
|
|
|
|
conf {
|
|
groups = "usb0_0_grp";
|
|
slew-rate = <SLEW_RATE_SLOW>;
|
|
power-source = <IO_STANDARD_LVCMOS18>;
|
|
drive-strength = <12>;
|
|
};
|
|
|
|
conf-rx {
|
|
pins = "MIO52", "MIO53", "MIO55";
|
|
bias-high-impedance;
|
|
};
|
|
|
|
conf-tx {
|
|
pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
|
|
"MIO60", "MIO61", "MIO62", "MIO63";
|
|
bias-disable;
|
|
};
|
|
};
|
|
};
|
|
|
|
&psgtr {
|
|
status = "okay";
|
|
/* nc, sata, usb3, dp */
|
|
clocks = <&clock_8t49n287_5>, <&clock_8t49n287_2>, <&clock_8t49n287_3>;
|
|
clock-names = "ref1", "ref2", "ref3";
|
|
};
|
|
|
|
&qspi {
|
|
status = "okay";
|
|
flash@0 {
|
|
compatible = "m25p80", "jedec,spi-nor"; /* n25q512a 128MiB */
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
reg = <0x0>;
|
|
spi-tx-bus-width = <1>;
|
|
spi-rx-bus-width = <4>;
|
|
spi-max-frequency = <108000000>; /* Based on DC1 spec */
|
|
partition@0 { /* for testing purpose */
|
|
label = "qspi-fsbl-uboot";
|
|
reg = <0x0 0x100000>;
|
|
};
|
|
partition@100000 { /* for testing purpose */
|
|
label = "qspi-linux";
|
|
reg = <0x100000 0x500000>;
|
|
};
|
|
partition@600000 { /* for testing purpose */
|
|
label = "qspi-device-tree";
|
|
reg = <0x600000 0x20000>;
|
|
};
|
|
partition@620000 { /* for testing purpose */
|
|
label = "qspi-rootfs";
|
|
reg = <0x620000 0x5E0000>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&rtc {
|
|
status = "okay";
|
|
};
|
|
|
|
&sata {
|
|
status = "okay";
|
|
/* SATA OOB timing settings */
|
|
ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
|
|
ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
|
|
ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
|
|
ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
|
|
ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
|
|
ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
|
|
ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
|
|
ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
|
|
phy-names = "sata-phy";
|
|
phys = <&psgtr 3 PHY_TYPE_SATA 1 1>;
|
|
};
|
|
|
|
/* SD1 with level shifter */
|
|
&sdhci1 {
|
|
status = "okay";
|
|
no-1-8-v;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_sdhci1_default>;
|
|
xlnx,mio-bank = <1>;
|
|
disable-wp;
|
|
};
|
|
|
|
&uart0 {
|
|
status = "okay";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_uart0_default>;
|
|
};
|
|
|
|
&uart1 {
|
|
status = "okay";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_uart1_default>;
|
|
};
|
|
|
|
/* ULPI SMSC USB3320 */
|
|
&usb0 {
|
|
status = "okay";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_usb0_default>;
|
|
};
|
|
|
|
&dwc3_0 {
|
|
status = "okay";
|
|
dr_mode = "host";
|
|
snps,usb3_lpm_capable;
|
|
phy-names = "usb3-phy";
|
|
phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
|
|
maximum-speed = "super-speed";
|
|
};
|
|
|
|
&watchdog0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&xilinx_ams {
|
|
status = "okay";
|
|
};
|
|
|
|
&ams_ps {
|
|
status = "okay";
|
|
};
|
|
|
|
&ams_pl {
|
|
status = "okay";
|
|
};
|
|
|
|
&zynqmp_dpdma {
|
|
status = "okay";
|
|
};
|
|
|
|
&zynqmp_dpsub {
|
|
status = "okay";
|
|
phy-names = "dp-phy0", "dp-phy1";
|
|
phys = <&psgtr 1 PHY_TYPE_DP 0 3>,
|
|
<&psgtr 0 PHY_TYPE_DP 1 3>;
|
|
};
|