mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-15 15:53:02 +00:00
cda8f87349
If probing caam_jr returns failure, the variable "dev" will not be initialized, so we can't use dev->name for the error print. Otherwise it will cause crash. Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Gaurav Jain <gaurav.jain@nxp.com>
425 lines
9.7 KiB
C
425 lines
9.7 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright (C) 2016 Freescale Semiconductor, Inc.
|
|
* Copyright 2021 NXP
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <cpu_func.h>
|
|
#include <init.h>
|
|
#include <log.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/clock.h>
|
|
#include <asm/arch/imx-regs.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <asm/mach-imx/boot_mode.h>
|
|
#include <asm/mach-imx/hab.h>
|
|
#include <asm/mach-imx/sys_proto.h>
|
|
#include <asm/setup.h>
|
|
#include <linux/bitops.h>
|
|
#include <dm.h>
|
|
|
|
#define PMC0_BASE_ADDR 0x410a1000
|
|
#define PMC0_CTRL 0x28
|
|
#define PMC0_CTRL_LDOEN BIT(31)
|
|
#define PMC0_CTRL_LDOOKDIS BIT(30)
|
|
#define PMC0_CTRL_PMC1ON BIT(24)
|
|
#define PMC1_BASE_ADDR 0x40400000
|
|
#define PMC1_RUN 0x8
|
|
#define PMC1_STOP 0x10
|
|
#define PMC1_VLPS 0x14
|
|
#define PMC1_LDOVL_SHIFT 16
|
|
#define PMC1_LDOVL_MASK (0x3f << PMC1_LDOVL_SHIFT)
|
|
#define PMC1_LDOVL_900 0x1e
|
|
#define PMC1_LDOVL_950 0x23
|
|
#define PMC1_STATUS 0x20
|
|
#define PMC1_STATUS_LDOVLF BIT(8)
|
|
|
|
static char *get_reset_cause(char *);
|
|
|
|
#if defined(CONFIG_IMX_HAB)
|
|
struct imx_sec_config_fuse_t const imx_sec_config_fuse = {
|
|
.bank = 29,
|
|
.word = 6,
|
|
};
|
|
#endif
|
|
|
|
#define ROM_VERSION_ADDR 0x80
|
|
u32 get_cpu_rev(void)
|
|
{
|
|
/* Check the ROM version for cpu revision */
|
|
u32 rom_version = readl((void __iomem *)ROM_VERSION_ADDR);
|
|
|
|
return (MXC_CPU_MX7ULP << 12) | (rom_version & 0xFF);
|
|
}
|
|
|
|
#ifdef CONFIG_REVISION_TAG
|
|
u32 __weak get_board_rev(void)
|
|
{
|
|
return get_cpu_rev();
|
|
}
|
|
#endif
|
|
|
|
enum bt_mode get_boot_mode(void)
|
|
{
|
|
u32 bt0_cfg = 0;
|
|
|
|
bt0_cfg = readl(CMC0_RBASE + 0x40);
|
|
bt0_cfg &= (BT0CFG_LPBOOT_MASK | BT0CFG_DUALBOOT_MASK);
|
|
|
|
if (!(bt0_cfg & BT0CFG_LPBOOT_MASK)) {
|
|
/* No low power boot */
|
|
if (bt0_cfg & BT0CFG_DUALBOOT_MASK)
|
|
return DUAL_BOOT;
|
|
else
|
|
return SINGLE_BOOT;
|
|
}
|
|
|
|
return LOW_POWER_BOOT;
|
|
}
|
|
|
|
int arch_cpu_init(void)
|
|
{
|
|
enable_ca7_smp();
|
|
return 0;
|
|
}
|
|
|
|
#if defined(CONFIG_ARCH_MISC_INIT)
|
|
int arch_misc_init(void)
|
|
{
|
|
if (IS_ENABLED(CONFIG_FSL_CAAM)) {
|
|
struct udevice *dev;
|
|
int ret;
|
|
|
|
ret = uclass_get_device_by_driver(UCLASS_MISC, DM_DRIVER_GET(caam_jr), &dev);
|
|
if (ret)
|
|
printf("Failed to initialize caam_jr: %d\n", ret);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_BOARD_POSTCLK_INIT
|
|
int board_postclk_init(void)
|
|
{
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
#define UNLOCK_WORD0 0xC520 /* 1st unlock word */
|
|
#define UNLOCK_WORD1 0xD928 /* 2nd unlock word */
|
|
#define REFRESH_WORD0 0xA602 /* 1st refresh word */
|
|
#define REFRESH_WORD1 0xB480 /* 2nd refresh word */
|
|
|
|
static void disable_wdog(u32 wdog_base)
|
|
{
|
|
u32 val_cs = readl(wdog_base + 0x00);
|
|
|
|
if (!(val_cs & 0x80))
|
|
return;
|
|
|
|
dmb();
|
|
__raw_writel(REFRESH_WORD0, (wdog_base + 0x04)); /* Refresh the CNT */
|
|
__raw_writel(REFRESH_WORD1, (wdog_base + 0x04));
|
|
dmb();
|
|
|
|
if (!(val_cs & 800)) {
|
|
dmb();
|
|
__raw_writel(UNLOCK_WORD0, (wdog_base + 0x04));
|
|
__raw_writel(UNLOCK_WORD1, (wdog_base + 0x04));
|
|
dmb();
|
|
|
|
while (!(readl(wdog_base + 0x00) & 0x800));
|
|
}
|
|
dmb();
|
|
__raw_writel(0x0, wdog_base + 0x0C); /* Set WIN to 0 */
|
|
__raw_writel(0x400, wdog_base + 0x08); /* Set timeout to default 0x400 */
|
|
__raw_writel(0x120, wdog_base + 0x00); /* Disable it and set update */
|
|
dmb();
|
|
|
|
while (!(readl(wdog_base + 0x00) & 0x400));
|
|
}
|
|
|
|
void init_wdog(void)
|
|
{
|
|
/*
|
|
* ROM will configure WDOG1, disable it or enable it
|
|
* depending on FUSE. The update bit is set for reconfigurable.
|
|
* We have to use unlock sequence to reconfigure it.
|
|
* WDOG2 is not touched by ROM, so it will have default value
|
|
* which is enabled. We can directly configure it.
|
|
* To simplify the codes, we still use same reconfigure
|
|
* process as WDOG1. Because the update bit is not set for
|
|
* WDOG2, the unlock sequence won't take effect really.
|
|
* It actually directly configure the wdog.
|
|
* In this function, we will disable both WDOG1 and WDOG2,
|
|
* and set update bit for both. So that kernel can reconfigure them.
|
|
*/
|
|
disable_wdog(WDG1_RBASE);
|
|
disable_wdog(WDG2_RBASE);
|
|
}
|
|
|
|
static bool ldo_mode_is_enabled(void)
|
|
{
|
|
unsigned int reg;
|
|
|
|
reg = readl(PMC0_BASE_ADDR + PMC0_CTRL);
|
|
if (reg & PMC0_CTRL_LDOEN)
|
|
return true;
|
|
else
|
|
return false;
|
|
}
|
|
|
|
#if !defined(CONFIG_SPL) || (defined(CONFIG_SPL) && defined(CONFIG_SPL_BUILD))
|
|
#if defined(CONFIG_LDO_ENABLED_MODE)
|
|
static void init_ldo_mode(void)
|
|
{
|
|
unsigned int reg;
|
|
|
|
if (ldo_mode_is_enabled())
|
|
return;
|
|
|
|
/* Set LDOOKDIS */
|
|
setbits_le32(PMC0_BASE_ADDR + PMC0_CTRL, PMC0_CTRL_LDOOKDIS);
|
|
|
|
/* Set LDOVL to 0.95V in PMC1_RUN */
|
|
reg = readl(PMC1_BASE_ADDR + PMC1_RUN);
|
|
reg &= ~PMC1_LDOVL_MASK;
|
|
reg |= (PMC1_LDOVL_950 << PMC1_LDOVL_SHIFT);
|
|
writel(PMC1_BASE_ADDR + PMC1_RUN, reg);
|
|
|
|
/* Wait for LDOVLF to be cleared */
|
|
reg = readl(PMC1_BASE_ADDR + PMC1_STATUS);
|
|
while (reg & PMC1_STATUS_LDOVLF)
|
|
;
|
|
|
|
/* Set LDOVL to 0.95V in PMC1_STOP */
|
|
reg = readl(PMC1_BASE_ADDR + PMC1_STOP);
|
|
reg &= ~PMC1_LDOVL_MASK;
|
|
reg |= (PMC1_LDOVL_950 << PMC1_LDOVL_SHIFT);
|
|
writel(PMC1_BASE_ADDR + PMC1_STOP, reg);
|
|
|
|
/* Set LDOVL to 0.90V in PMC1_VLPS */
|
|
reg = readl(PMC1_BASE_ADDR + PMC1_VLPS);
|
|
reg &= ~PMC1_LDOVL_MASK;
|
|
reg |= (PMC1_LDOVL_900 << PMC1_LDOVL_SHIFT);
|
|
writel(PMC1_BASE_ADDR + PMC1_VLPS, reg);
|
|
|
|
/* Set LDOEN bit */
|
|
setbits_le32(PMC0_BASE_ADDR + PMC0_CTRL, PMC0_CTRL_LDOEN);
|
|
|
|
/* Set the PMC1ON bit */
|
|
setbits_le32(PMC0_BASE_ADDR + PMC0_CTRL, PMC0_CTRL_PMC1ON);
|
|
}
|
|
#endif
|
|
|
|
void s_init(void)
|
|
{
|
|
/* Disable wdog */
|
|
init_wdog();
|
|
|
|
/* clock configuration. */
|
|
clock_init();
|
|
|
|
if (soc_rev() < CHIP_REV_2_0) {
|
|
/* enable dumb pmic */
|
|
writel((readl(SNVS_LP_LPCR) | SNVS_LPCR_DPEN), SNVS_LP_LPCR);
|
|
}
|
|
|
|
#if defined(CONFIG_LDO_ENABLED_MODE)
|
|
init_ldo_mode();
|
|
#endif
|
|
return;
|
|
}
|
|
#endif
|
|
|
|
#ifndef CONFIG_ULP_WATCHDOG
|
|
void reset_cpu(void)
|
|
{
|
|
setbits_le32(SIM0_RBASE, SIM_SOPT1_A7_SW_RESET);
|
|
while (1)
|
|
;
|
|
}
|
|
#endif
|
|
|
|
#if defined(CONFIG_DISPLAY_CPUINFO)
|
|
const char *get_imx_type(u32 imxtype)
|
|
{
|
|
return "7ULP";
|
|
}
|
|
|
|
int print_cpuinfo(void)
|
|
{
|
|
u32 cpurev;
|
|
char cause[18];
|
|
|
|
cpurev = get_cpu_rev();
|
|
|
|
printf("CPU: Freescale i.MX%s rev%d.%d at %d MHz\n",
|
|
get_imx_type((cpurev & 0xFF000) >> 12),
|
|
(cpurev & 0x000F0) >> 4, (cpurev & 0x0000F) >> 0,
|
|
mxc_get_clock(MXC_ARM_CLK) / 1000000);
|
|
|
|
printf("Reset cause: %s\n", get_reset_cause(cause));
|
|
|
|
printf("Boot mode: ");
|
|
switch (get_boot_mode()) {
|
|
case LOW_POWER_BOOT:
|
|
printf("Low power boot\n");
|
|
break;
|
|
case DUAL_BOOT:
|
|
printf("Dual boot\n");
|
|
break;
|
|
case SINGLE_BOOT:
|
|
default:
|
|
printf("Single boot\n");
|
|
break;
|
|
}
|
|
|
|
if (ldo_mode_is_enabled())
|
|
printf("PMC1: LDO enabled mode\n");
|
|
else
|
|
printf("PMC1: LDO bypass mode\n");
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
#define CMC_SRS_TAMPER (1 << 31)
|
|
#define CMC_SRS_SECURITY (1 << 30)
|
|
#define CMC_SRS_TZWDG (1 << 29)
|
|
#define CMC_SRS_JTAG_RST (1 << 28)
|
|
#define CMC_SRS_CORE1 (1 << 16)
|
|
#define CMC_SRS_LOCKUP (1 << 15)
|
|
#define CMC_SRS_SW (1 << 14)
|
|
#define CMC_SRS_WDG (1 << 13)
|
|
#define CMC_SRS_PIN_RESET (1 << 8)
|
|
#define CMC_SRS_WARM (1 << 4)
|
|
#define CMC_SRS_HVD (1 << 3)
|
|
#define CMC_SRS_LVD (1 << 2)
|
|
#define CMC_SRS_POR (1 << 1)
|
|
#define CMC_SRS_WUP (1 << 0)
|
|
|
|
static u32 reset_cause = -1;
|
|
|
|
static char *get_reset_cause(char *ret)
|
|
{
|
|
u32 cause1, cause = 0, srs = 0;
|
|
u32 *reg_ssrs = (u32 *)(SRC_BASE_ADDR + 0x28);
|
|
u32 *reg_srs = (u32 *)(SRC_BASE_ADDR + 0x20);
|
|
|
|
if (!ret)
|
|
return "null";
|
|
|
|
srs = readl(reg_srs);
|
|
cause1 = readl(reg_ssrs);
|
|
writel(cause1, reg_ssrs);
|
|
|
|
reset_cause = cause1;
|
|
|
|
cause = cause1 & (CMC_SRS_POR | CMC_SRS_WUP | CMC_SRS_WARM);
|
|
|
|
switch (cause) {
|
|
case CMC_SRS_POR:
|
|
sprintf(ret, "%s", "POR");
|
|
break;
|
|
case CMC_SRS_WUP:
|
|
sprintf(ret, "%s", "WUP");
|
|
break;
|
|
case CMC_SRS_WARM:
|
|
cause = cause1 & (CMC_SRS_WDG | CMC_SRS_SW |
|
|
CMC_SRS_JTAG_RST);
|
|
switch (cause) {
|
|
case CMC_SRS_WDG:
|
|
sprintf(ret, "%s", "WARM-WDG");
|
|
break;
|
|
case CMC_SRS_SW:
|
|
sprintf(ret, "%s", "WARM-SW");
|
|
break;
|
|
case CMC_SRS_JTAG_RST:
|
|
sprintf(ret, "%s", "WARM-JTAG");
|
|
break;
|
|
default:
|
|
sprintf(ret, "%s", "WARM-UNKN");
|
|
break;
|
|
}
|
|
break;
|
|
default:
|
|
sprintf(ret, "%s-%X", "UNKN", cause1);
|
|
break;
|
|
}
|
|
|
|
debug("[%X] SRS[%X] %X - ", cause1, srs, srs^cause1);
|
|
return ret;
|
|
}
|
|
|
|
#ifdef CONFIG_ENV_IS_IN_MMC
|
|
__weak int board_mmc_get_env_dev(int devno)
|
|
{
|
|
return CONFIG_SYS_MMC_ENV_DEV;
|
|
}
|
|
|
|
int mmc_get_env_dev(void)
|
|
{
|
|
int devno = 0;
|
|
u32 bt1_cfg = 0;
|
|
|
|
/* If not boot from sd/mmc, use default value */
|
|
if (get_boot_mode() == LOW_POWER_BOOT)
|
|
return CONFIG_SYS_MMC_ENV_DEV;
|
|
|
|
bt1_cfg = readl(CMC1_RBASE + 0x40);
|
|
devno = (bt1_cfg >> 9) & 0x7;
|
|
|
|
return board_mmc_get_env_dev(devno);
|
|
}
|
|
#endif
|
|
|
|
enum boot_device get_boot_device(void)
|
|
{
|
|
struct bootrom_sw_info **p =
|
|
(struct bootrom_sw_info **)ROM_SW_INFO_ADDR;
|
|
|
|
enum boot_device boot_dev = SD1_BOOT;
|
|
u8 boot_type = (*p)->boot_dev_type;
|
|
u8 boot_instance = (*p)->boot_dev_instance;
|
|
|
|
switch (boot_type) {
|
|
case BOOT_TYPE_SD:
|
|
boot_dev = boot_instance + SD1_BOOT;
|
|
break;
|
|
case BOOT_TYPE_MMC:
|
|
boot_dev = boot_instance + MMC1_BOOT;
|
|
break;
|
|
case BOOT_TYPE_USB:
|
|
boot_dev = USB_BOOT;
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
|
|
return boot_dev;
|
|
}
|
|
|
|
#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
|
|
/*
|
|
* OCOTP_CFG (SJC CHALLENGE, Unique ID)
|
|
* i.MX 7ULP Applications Processor Reference Manual, Rev. 0, 09/2020
|
|
*
|
|
* OCOTP_CFG0 offset 0x4B0: 15:0 -> 15:0 bits of Unique ID
|
|
* OCOTP_CFG1 offset 0x4C0: 15:0 -> 31:16 bits of Unique ID
|
|
* OCOTP_CFG2 offset 0x4D0: 15:0 -> 47:32 bits of Unique ID
|
|
* OCOTP_CFG3 offset 0x4E0: 15:0 -> 63:48 bits of Unique ID
|
|
*/
|
|
void get_board_serial(struct tag_serialnr *serialnr)
|
|
{
|
|
struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR;
|
|
struct fuse_bank *bank = &ocotp->bank[1];
|
|
struct fuse_bank1_regs *fuse =
|
|
(struct fuse_bank1_regs *)bank->fuse_regs;
|
|
|
|
serialnr->low = (fuse->cfg0 & 0xFFFF) + ((fuse->cfg1 & 0xFFFF) << 16);
|
|
serialnr->high = (fuse->cfg2 & 0xFFFF) + ((fuse->cfg3 & 0xFFFF) << 16);
|
|
}
|
|
#endif /* CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG */
|