mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-01 17:10:11 +00:00
565cfcf0e1
On mx6qsabreauto the parallel NOR width is 16 bits, so pass configure CONFIG_SYS_FLASH_CFI_WIDTH correctly so that the CFI driver does not use 8 bits by default. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
78 lines
2.4 KiB
C
78 lines
2.4 KiB
C
/*
|
|
* Copyright (C) 2012 Freescale Semiconductor, Inc.
|
|
*
|
|
* Configuration settings for the Freescale i.MX6Q SabreAuto board.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#ifndef __MX6QSABREAUTO_CONFIG_H
|
|
#define __MX6QSABREAUTO_CONFIG_H
|
|
|
|
#define CONFIG_MACH_TYPE 3529
|
|
#define CONFIG_MXC_UART_BASE UART4_BASE
|
|
#define CONSOLE_DEV "ttymxc3"
|
|
#define CONFIG_MMCROOT "/dev/mmcblk0p2"
|
|
|
|
/* USB Configs */
|
|
#define CONFIG_USB_EHCI
|
|
#define CONFIG_USB_EHCI_MX6
|
|
#define CONFIG_USB_HOST_ETHER
|
|
#define CONFIG_USB_ETHER_ASIX
|
|
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
|
|
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* For OTG port */
|
|
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
|
|
#define CONFIG_MXC_USB_FLAGS 0
|
|
|
|
#define CONFIG_PCA953X
|
|
#define CONFIG_SYS_I2C_PCA953X_WIDTH { {0x30, 8}, {0x32, 8}, {0x34, 8} }
|
|
|
|
#include "mx6sabre_common.h"
|
|
|
|
#undef CONFIG_SYS_NO_FLASH
|
|
#define CONFIG_SYS_FLASH_BASE WEIM_ARB_BASE_ADDR
|
|
#define CONFIG_SYS_FLASH_SECT_SIZE (128 * 1024)
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
|
|
#define CONFIG_SYS_FLASH_CFI /* Flash memory is CFI compliant */
|
|
#define CONFIG_FLASH_CFI_DRIVER /* Use drivers/cfi_flash.c */
|
|
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* Use buffered writes*/
|
|
#define CONFIG_SYS_FLASH_EMPTY_INFO
|
|
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
|
|
|
|
#define CONFIG_SYS_FSL_USDHC_NUM 2
|
|
#if defined(CONFIG_ENV_IS_IN_MMC)
|
|
#define CONFIG_SYS_MMC_ENV_DEV 0
|
|
#endif
|
|
|
|
/* I2C Configs */
|
|
#define CONFIG_SYS_I2C
|
|
#define CONFIG_SYS_I2C_MXC
|
|
#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
|
|
#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
|
|
#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
|
|
#define CONFIG_SYS_I2C_SPEED 100000
|
|
|
|
/* NAND flash command */
|
|
#define CONFIG_CMD_NAND
|
|
#define CONFIG_CMD_NAND_TRIMFFS
|
|
|
|
/* NAND stuff */
|
|
#define CONFIG_NAND_MXS
|
|
#define CONFIG_SYS_MAX_NAND_DEVICE 1
|
|
#define CONFIG_SYS_NAND_BASE 0x40000000
|
|
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
|
|
#define CONFIG_SYS_NAND_ONFI_DETECTION
|
|
|
|
/* DMA stuff, needed for GPMI/MXS NAND support */
|
|
#define CONFIG_APBH_DMA
|
|
#define CONFIG_APBH_DMA_BURST
|
|
#define CONFIG_APBH_DMA_BURST8
|
|
|
|
/* PMIC */
|
|
#define CONFIG_POWER
|
|
#define CONFIG_POWER_I2C
|
|
#define CONFIG_POWER_PFUZE100
|
|
#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
|
|
|
|
#endif /* __MX6QSABREAUTO_CONFIG_H */
|