u-boot/board/samsung/trats/trats.c
Przemyslaw Marczak 4a1883651f trats/trats2: exynos_power_init: return 0 if no battery detected.
Generic board support is now enabled for Exynos 4, and if any
init function returns an error then the init process is stopped.

This makes a boot issue on the Trats and Trats2 devices. If the device
is supplied by USB cable or an external power supply then it can't boot
because function exynos_power_init returns an error. Now this function
returns 0 if battery is not connected.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Piotr Wilczek <p.wilczek@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-06-19 09:37:16 +09:00

599 lines
16 KiB
C

/*
* Copyright (C) 2011 Samsung Electronics
* Heungjun Kim <riverful.kim@samsung.com>
* Kyungmin Park <kyungmin.park@samsung.com>
* Donghwa Lee <dh09.lee@samsung.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <lcd.h>
#include <asm/io.h>
#include <asm/arch/cpu.h>
#include <asm/arch/gpio.h>
#include <asm/arch/pinmux.h>
#include <asm/arch/clock.h>
#include <asm/arch/mipi_dsim.h>
#include <asm/arch/watchdog.h>
#include <asm/arch/power.h>
#include <power/pmic.h>
#include <usb/s3c_udc.h>
#include <power/max8997_pmic.h>
#include <power/max8997_muic.h>
#include <power/battery.h>
#include <power/max17042_fg.h>
#include <libtizen.h>
#include <usb.h>
#include <usb_mass_storage.h>
#include "setup.h"
DECLARE_GLOBAL_DATA_PTR;
unsigned int board_rev;
#ifdef CONFIG_REVISION_TAG
u32 get_board_rev(void)
{
return board_rev;
}
#endif
static void check_hw_revision(void);
struct s3c_plat_otg_data s5pc210_otg_data;
int exynos_init(void)
{
check_hw_revision();
printf("HW Revision:\t0x%x\n", board_rev);
return 0;
}
void i2c_init_board(void)
{
int err;
/* I2C_5 -> PMIC */
err = exynos_pinmux_config(PERIPH_ID_I2C5, PINMUX_FLAG_NONE);
if (err) {
debug("I2C%d not configured\n", (I2C_5));
return;
}
/* I2C_8 -> FG */
gpio_direction_output(EXYNOS4_GPIO_Y40, 1);
gpio_direction_output(EXYNOS4_GPIO_Y41, 1);
}
static void trats_low_power_mode(void)
{
struct exynos4_clock *clk =
(struct exynos4_clock *)samsung_get_base_clock();
struct exynos4_power *pwr =
(struct exynos4_power *)samsung_get_base_power();
/* Power down CORE1 */
/* LOCAL_PWR_CFG [1:0] 0x3 EN, 0x0 DIS */
writel(0x0, &pwr->arm_core1_configuration);
/* Change the APLL frequency */
/* ENABLE (1 enable) | LOCKED (1 locked) */
/* [31] | [29] */
/* FSEL | MDIV | PDIV | SDIV */
/* [27] | [25:16] | [13:8] | [2:0] */
writel(0xa0c80604, &clk->apll_con0);
/* Change CPU0 clock divider */
/* CORE2_RATIO | APLL_RATIO | PCLK_DBG_RATIO | ATB_RATIO */
/* [30:28] | [26:24] | [22:20] | [18:16] */
/* PERIPH_RATIO | COREM1_RATIO | COREM0_RATIO | CORE_RATIO */
/* [14:12] | [10:8] | [6:4] | [2:0] */
writel(0x00000100, &clk->div_cpu0);
/* CLK_DIV_STAT_CPU0 - wait until clock gets stable (0 = stable) */
while (readl(&clk->div_stat_cpu0) & 0x1111111)
continue;
/* Change clock divider ratio for DMC */
/* DMCP_RATIO | DMCD_RATIO */
/* [22:20] | [18:16] */
/* DMC_RATIO | DPHY_RATIO | ACP_PCLK_RATIO | ACP_RATIO */
/* [14:12] | [10:8] | [6:4] | [2:0] */
writel(0x13113117, &clk->div_dmc0);
/* CLK_DIV_STAT_DMC0 - wait until clock gets stable (0 = stable) */
while (readl(&clk->div_stat_dmc0) & 0x11111111)
continue;
/* Turn off unnecessary power domains */
writel(0x0, &pwr->xxti_configuration); /* XXTI */
writel(0x0, &pwr->cam_configuration); /* CAM */
writel(0x0, &pwr->tv_configuration); /* TV */
writel(0x0, &pwr->mfc_configuration); /* MFC */
writel(0x0, &pwr->g3d_configuration); /* G3D */
writel(0x0, &pwr->gps_configuration); /* GPS */
writel(0x0, &pwr->gps_alive_configuration); /* GPS_ALIVE */
/* Turn off unnecessary clocks */
writel(0x0, &clk->gate_ip_cam); /* CAM */
writel(0x0, &clk->gate_ip_tv); /* TV */
writel(0x0, &clk->gate_ip_mfc); /* MFC */
writel(0x0, &clk->gate_ip_g3d); /* G3D */
writel(0x0, &clk->gate_ip_image); /* IMAGE */
writel(0x0, &clk->gate_ip_gps); /* GPS */
}
static int pmic_init_max8997(void)
{
struct pmic *p = pmic_get("MAX8997_PMIC");
int i = 0, ret = 0;
u32 val;
if (pmic_probe(p))
return -1;
/* BUCK1 VARM: 1.2V */
val = (1200000 - 650000) / 25000;
ret |= pmic_reg_write(p, MAX8997_REG_BUCK1DVS1, val);
val = ENBUCK | ACTIVE_DISCHARGE; /* DVS OFF */
ret |= pmic_reg_write(p, MAX8997_REG_BUCK1CTRL, val);
/* BUCK2 VINT: 1.1V */
val = (1100000 - 650000) / 25000;
ret |= pmic_reg_write(p, MAX8997_REG_BUCK2DVS1, val);
val = ENBUCK | ACTIVE_DISCHARGE; /* DVS OFF */
ret |= pmic_reg_write(p, MAX8997_REG_BUCK2CTRL, val);
/* BUCK3 G3D: 1.1V - OFF */
ret |= pmic_reg_read(p, MAX8997_REG_BUCK3CTRL, &val);
val &= ~ENBUCK;
ret |= pmic_reg_write(p, MAX8997_REG_BUCK3CTRL, val);
val = (1100000 - 750000) / 50000;
ret |= pmic_reg_write(p, MAX8997_REG_BUCK3DVS, val);
/* BUCK4 CAMISP: 1.2V - OFF */
ret |= pmic_reg_read(p, MAX8997_REG_BUCK4CTRL, &val);
val &= ~ENBUCK;
ret |= pmic_reg_write(p, MAX8997_REG_BUCK4CTRL, val);
val = (1200000 - 650000) / 25000;
ret |= pmic_reg_write(p, MAX8997_REG_BUCK4DVS, val);
/* BUCK5 VMEM: 1.2V */
val = (1200000 - 650000) / 25000;
for (i = 0; i < 8; i++)
ret |= pmic_reg_write(p, MAX8997_REG_BUCK5DVS1 + i, val);
val = ENBUCK | ACTIVE_DISCHARGE; /* DVS OFF */
ret |= pmic_reg_write(p, MAX8997_REG_BUCK5CTRL, val);
/* BUCK6 CAM AF: 2.8V */
/* No Voltage Setting Register */
/* GNSLCT 3.0X */
val = GNSLCT;
ret |= pmic_reg_write(p, MAX8997_REG_BUCK6CTRL, val);
/* BUCK7 VCC_SUB: 2.0V */
val = (2000000 - 750000) / 50000;
ret |= pmic_reg_write(p, MAX8997_REG_BUCK7DVS, val);
/* LDO1 VADC: 3.3V */
val = max8997_reg_ldo(3300000) | DIS_LDO; /* OFF */
ret |= pmic_reg_write(p, MAX8997_REG_LDO1CTRL, val);
/* LDO1 Disable active discharging */
ret |= pmic_reg_read(p, MAX8997_REG_LDO1CONFIG, &val);
val &= ~LDO_ADE;
ret |= pmic_reg_write(p, MAX8997_REG_LDO1CONFIG, val);
/* LDO2 VALIVE: 1.1V */
val = max8997_reg_ldo(1100000) | EN_LDO;
ret |= pmic_reg_write(p, MAX8997_REG_LDO2CTRL, val);
/* LDO3 VUSB/MIPI: 1.1V */
val = max8997_reg_ldo(1100000) | DIS_LDO; /* OFF */
ret |= pmic_reg_write(p, MAX8997_REG_LDO3CTRL, val);
/* LDO4 VMIPI: 1.8V */
val = max8997_reg_ldo(1800000) | DIS_LDO; /* OFF */
ret |= pmic_reg_write(p, MAX8997_REG_LDO4CTRL, val);
/* LDO5 VHSIC: 1.2V */
val = max8997_reg_ldo(1200000) | DIS_LDO; /* OFF */
ret |= pmic_reg_write(p, MAX8997_REG_LDO5CTRL, val);
/* LDO6 VCC_1.8V_PDA: 1.8V */
val = max8997_reg_ldo(1800000) | EN_LDO;
ret |= pmic_reg_write(p, MAX8997_REG_LDO6CTRL, val);
/* LDO7 CAM_ISP: 1.8V */
val = max8997_reg_ldo(1800000) | DIS_LDO; /* OFF */
ret |= pmic_reg_write(p, MAX8997_REG_LDO7CTRL, val);
/* LDO8 VDAC/VUSB: 3.3V */
val = max8997_reg_ldo(3300000) | DIS_LDO; /* OFF */
ret |= pmic_reg_write(p, MAX8997_REG_LDO8CTRL, val);
/* LDO9 VCC_2.8V_PDA: 2.8V */
val = max8997_reg_ldo(2800000) | EN_LDO;
ret |= pmic_reg_write(p, MAX8997_REG_LDO9CTRL, val);
/* LDO10 VPLL: 1.1V */
val = max8997_reg_ldo(1100000) | EN_LDO;
ret |= pmic_reg_write(p, MAX8997_REG_LDO10CTRL, val);
/* LDO11 TOUCH: 2.8V */
val = max8997_reg_ldo(2800000) | DIS_LDO; /* OFF */
ret |= pmic_reg_write(p, MAX8997_REG_LDO11CTRL, val);
/* LDO12 VTCAM: 1.8V */
val = max8997_reg_ldo(1800000) | DIS_LDO; /* OFF */
ret |= pmic_reg_write(p, MAX8997_REG_LDO12CTRL, val);
/* LDO13 VCC_3.0_LCD: 3.0V */
val = max8997_reg_ldo(3000000) | DIS_LDO; /* OFF */
ret |= pmic_reg_write(p, MAX8997_REG_LDO13CTRL, val);
/* LDO14 MOTOR: 3.0V */
val = max8997_reg_ldo(3000000) | DIS_LDO; /* OFF */
ret |= pmic_reg_write(p, MAX8997_REG_LDO14CTRL, val);
/* LDO15 LED_A: 2.8V */
val = max8997_reg_ldo(2800000) | DIS_LDO; /* OFF */
ret |= pmic_reg_write(p, MAX8997_REG_LDO15CTRL, val);
/* LDO16 CAM_SENSOR: 1.8V */
val = max8997_reg_ldo(1800000) | DIS_LDO; /* OFF */
ret |= pmic_reg_write(p, MAX8997_REG_LDO16CTRL, val);
/* LDO17 VTF: 2.8V */
val = max8997_reg_ldo(2800000) | DIS_LDO; /* OFF */
ret |= pmic_reg_write(p, MAX8997_REG_LDO17CTRL, val);
/* LDO18 TOUCH_LED 3.3V */
val = max8997_reg_ldo(3300000) | DIS_LDO; /* OFF */
ret |= pmic_reg_write(p, MAX8997_REG_LDO18CTRL, val);
/* LDO21 VDDQ: 1.2V */
val = max8997_reg_ldo(1200000) | EN_LDO;
ret |= pmic_reg_write(p, MAX8997_REG_LDO21CTRL, val);
/* SAFEOUT for both 1 and 2: 4.9V, Active discharge, Enable */
val = (SAFEOUT_4_90V << 0) | (SAFEOUT_4_90V << 2) |
ACTDISSAFEO1 | ACTDISSAFEO2 | ENSAFEOUT1 | ENSAFEOUT2;
ret |= pmic_reg_write(p, MAX8997_REG_SAFEOUTCTRL, val);
if (ret) {
puts("MAX8997 PMIC setting error!\n");
return -1;
}
return 0;
}
int exynos_power_init(void)
{
int chrg, ret;
struct power_battery *pb;
struct pmic *p_fg, *p_chrg, *p_muic, *p_bat;
/*
* For PMIC/MUIC the I2C bus is named as I2C5, but it is connected
* to logical I2C adapter 0
*
* The FUEL_GAUGE is marked as I2C9 on the schematic, but connected
* to logical I2C adapter 1
*/
ret = pmic_init(I2C_5);
ret |= pmic_init_max8997();
ret |= power_fg_init(I2C_9);
ret |= power_muic_init(I2C_5);
ret |= power_bat_init(0);
if (ret)
return ret;
p_fg = pmic_get("MAX17042_FG");
if (!p_fg) {
puts("MAX17042_FG: Not found\n");
return -ENODEV;
}
p_chrg = pmic_get("MAX8997_PMIC");
if (!p_chrg) {
puts("MAX8997_PMIC: Not found\n");
return -ENODEV;
}
p_muic = pmic_get("MAX8997_MUIC");
if (!p_muic) {
puts("MAX8997_MUIC: Not found\n");
return -ENODEV;
}
p_bat = pmic_get("BAT_TRATS");
if (!p_bat) {
puts("BAT_TRATS: Not found\n");
return -ENODEV;
}
p_fg->parent = p_bat;
p_chrg->parent = p_bat;
p_muic->parent = p_bat;
p_bat->low_power_mode = trats_low_power_mode;
p_bat->pbat->battery_init(p_bat, p_fg, p_chrg, p_muic);
pb = p_bat->pbat;
chrg = p_muic->chrg->chrg_type(p_muic);
debug("CHARGER TYPE: %d\n", chrg);
if (!p_chrg->chrg->chrg_bat_present(p_chrg)) {
puts("No battery detected\n");
return 0;
}
p_fg->fg->fg_battery_check(p_fg, p_bat);
if (pb->bat->state == CHARGE && chrg == CHARGER_USB)
puts("CHARGE Battery !\n");
return 0;
}
static unsigned int get_hw_revision(void)
{
int hwrev = 0;
int i;
/* hw_rev[3:0] == GPE1[3:0] */
for (i = EXYNOS4_GPIO_E10; i < EXYNOS4_GPIO_E14; i++) {
gpio_cfg_pin(i, S5P_GPIO_INPUT);
gpio_set_pull(i, S5P_GPIO_PULL_NONE);
}
udelay(1);
for (i = 0; i < 4; i++)
hwrev |= (gpio_get_value(EXYNOS4_GPIO_E10 + i) << i);
debug("hwrev 0x%x\n", hwrev);
return hwrev;
}
static void check_hw_revision(void)
{
int hwrev;
hwrev = get_hw_revision();
board_rev |= hwrev;
}
#ifdef CONFIG_USB_GADGET
static int s5pc210_phy_control(int on)
{
int ret = 0;
u32 val = 0;
struct pmic *p = pmic_get("MAX8997_PMIC");
if (!p)
return -ENODEV;
if (pmic_probe(p))
return -1;
if (on) {
ret |= pmic_set_output(p, MAX8997_REG_SAFEOUTCTRL,
ENSAFEOUT1, LDO_ON);
ret |= pmic_reg_read(p, MAX8997_REG_LDO3CTRL, &val);
ret |= pmic_reg_write(p, MAX8997_REG_LDO3CTRL, EN_LDO | val);
ret |= pmic_reg_read(p, MAX8997_REG_LDO8CTRL, &val);
ret |= pmic_reg_write(p, MAX8997_REG_LDO8CTRL, EN_LDO | val);
} else {
ret |= pmic_reg_read(p, MAX8997_REG_LDO8CTRL, &val);
ret |= pmic_reg_write(p, MAX8997_REG_LDO8CTRL, DIS_LDO | val);
ret |= pmic_reg_read(p, MAX8997_REG_LDO3CTRL, &val);
ret |= pmic_reg_write(p, MAX8997_REG_LDO3CTRL, DIS_LDO | val);
ret |= pmic_set_output(p, MAX8997_REG_SAFEOUTCTRL,
ENSAFEOUT1, LDO_OFF);
}
if (ret) {
puts("MAX8997 LDO setting error!\n");
return -1;
}
return 0;
}
struct s3c_plat_otg_data s5pc210_otg_data = {
.phy_control = s5pc210_phy_control,
.regs_phy = EXYNOS4_USBPHY_BASE,
.regs_otg = EXYNOS4_USBOTG_BASE,
.usb_phy_ctrl = EXYNOS4_USBPHY_CONTROL,
.usb_flags = PHY0_SLEEP,
};
int board_usb_init(int index, enum usb_init_type init)
{
debug("USB_udc_probe\n");
return s3c_udc_probe(&s5pc210_otg_data);
}
int g_dnl_board_usb_cable_connected(void)
{
struct pmic *muic = pmic_get("MAX8997_MUIC");
if (!muic)
return 0;
return !!muic->chrg->chrg_type(muic);
}
#endif
static void pmic_reset(void)
{
gpio_direction_output(EXYNOS4_GPIO_X07, 1);
gpio_set_pull(EXYNOS4_GPIO_X27, S5P_GPIO_PULL_NONE);
}
static void board_clock_init(void)
{
struct exynos4_clock *clk =
(struct exynos4_clock *)samsung_get_base_clock();
writel(CLK_SRC_CPU_VAL, (unsigned int)&clk->src_cpu);
writel(CLK_SRC_TOP0_VAL, (unsigned int)&clk->src_top0);
writel(CLK_SRC_FSYS_VAL, (unsigned int)&clk->src_fsys);
writel(CLK_SRC_PERIL0_VAL, (unsigned int)&clk->src_peril0);
writel(CLK_DIV_CPU0_VAL, (unsigned int)&clk->div_cpu0);
writel(CLK_DIV_CPU1_VAL, (unsigned int)&clk->div_cpu1);
writel(CLK_DIV_DMC0_VAL, (unsigned int)&clk->div_dmc0);
writel(CLK_DIV_DMC1_VAL, (unsigned int)&clk->div_dmc1);
writel(CLK_DIV_LEFTBUS_VAL, (unsigned int)&clk->div_leftbus);
writel(CLK_DIV_RIGHTBUS_VAL, (unsigned int)&clk->div_rightbus);
writel(CLK_DIV_TOP_VAL, (unsigned int)&clk->div_top);
writel(CLK_DIV_FSYS1_VAL, (unsigned int)&clk->div_fsys1);
writel(CLK_DIV_FSYS2_VAL, (unsigned int)&clk->div_fsys2);
writel(CLK_DIV_FSYS3_VAL, (unsigned int)&clk->div_fsys3);
writel(CLK_DIV_PERIL0_VAL, (unsigned int)&clk->div_peril0);
writel(CLK_DIV_PERIL3_VAL, (unsigned int)&clk->div_peril3);
writel(PLL_LOCKTIME, (unsigned int)&clk->apll_lock);
writel(PLL_LOCKTIME, (unsigned int)&clk->mpll_lock);
writel(PLL_LOCKTIME, (unsigned int)&clk->epll_lock);
writel(PLL_LOCKTIME, (unsigned int)&clk->vpll_lock);
writel(APLL_CON1_VAL, (unsigned int)&clk->apll_con1);
writel(APLL_CON0_VAL, (unsigned int)&clk->apll_con0);
writel(MPLL_CON1_VAL, (unsigned int)&clk->mpll_con1);
writel(MPLL_CON0_VAL, (unsigned int)&clk->mpll_con0);
writel(EPLL_CON1_VAL, (unsigned int)&clk->epll_con1);
writel(EPLL_CON0_VAL, (unsigned int)&clk->epll_con0);
writel(VPLL_CON1_VAL, (unsigned int)&clk->vpll_con1);
writel(VPLL_CON0_VAL, (unsigned int)&clk->vpll_con0);
writel(CLK_GATE_IP_CAM_VAL, (unsigned int)&clk->gate_ip_cam);
writel(CLK_GATE_IP_VP_VAL, (unsigned int)&clk->gate_ip_tv);
writel(CLK_GATE_IP_MFC_VAL, (unsigned int)&clk->gate_ip_mfc);
writel(CLK_GATE_IP_G3D_VAL, (unsigned int)&clk->gate_ip_g3d);
writel(CLK_GATE_IP_IMAGE_VAL, (unsigned int)&clk->gate_ip_image);
writel(CLK_GATE_IP_LCD0_VAL, (unsigned int)&clk->gate_ip_lcd0);
writel(CLK_GATE_IP_LCD1_VAL, (unsigned int)&clk->gate_ip_lcd1);
writel(CLK_GATE_IP_FSYS_VAL, (unsigned int)&clk->gate_ip_fsys);
writel(CLK_GATE_IP_GPS_VAL, (unsigned int)&clk->gate_ip_gps);
writel(CLK_GATE_IP_PERIL_VAL, (unsigned int)&clk->gate_ip_peril);
writel(CLK_GATE_IP_PERIR_VAL, (unsigned int)&clk->gate_ip_perir);
writel(CLK_GATE_BLOCK_VAL, (unsigned int)&clk->gate_block);
}
static void board_power_init(void)
{
struct exynos4_power *pwr =
(struct exynos4_power *)samsung_get_base_power();
/* PS HOLD */
writel(EXYNOS4_PS_HOLD_CON_VAL, (unsigned int)&pwr->ps_hold_control);
/* Set power down */
writel(0, (unsigned int)&pwr->cam_configuration);
writel(0, (unsigned int)&pwr->tv_configuration);
writel(0, (unsigned int)&pwr->mfc_configuration);
writel(0, (unsigned int)&pwr->g3d_configuration);
writel(0, (unsigned int)&pwr->lcd1_configuration);
writel(0, (unsigned int)&pwr->gps_configuration);
writel(0, (unsigned int)&pwr->gps_alive_configuration);
/* It is necessary to power down core 1 */
/* to successfully boot CPU1 in kernel */
writel(0, (unsigned int)&pwr->arm_core1_configuration);
}
static void exynos_uart_init(void)
{
/* UART_SEL GPY4[7] (part2) at EXYNOS4 */
gpio_set_pull(EXYNOS4_GPIO_Y47, S5P_GPIO_PULL_UP);
gpio_direction_output(EXYNOS4_GPIO_Y47, 1);
}
int exynos_early_init_f(void)
{
wdt_stop();
pmic_reset();
board_clock_init();
exynos_uart_init();
board_power_init();
return 0;
}
void exynos_reset_lcd(void)
{
gpio_direction_output(EXYNOS4_GPIO_Y45, 1);
udelay(10000);
gpio_direction_output(EXYNOS4_GPIO_Y45, 0);
udelay(10000);
gpio_direction_output(EXYNOS4_GPIO_Y45, 1);
}
int lcd_power(void)
{
int ret = 0;
struct pmic *p = pmic_get("MAX8997_PMIC");
if (!p)
return -ENODEV;
if (pmic_probe(p))
return 0;
/* LDO15 voltage: 2.2v */
ret |= pmic_reg_write(p, MAX8997_REG_LDO15CTRL, 0x1c | EN_LDO);
/* LDO13 voltage: 3.0v */
ret |= pmic_reg_write(p, MAX8997_REG_LDO13CTRL, 0x2c | EN_LDO);
if (ret) {
puts("MAX8997 LDO setting error!\n");
return -1;
}
return 0;
}
int mipi_power(void)
{
int ret = 0;
struct pmic *p = pmic_get("MAX8997_PMIC");
if (!p)
return -ENODEV;
if (pmic_probe(p))
return 0;
/* LDO3 voltage: 1.1v */
ret |= pmic_reg_write(p, MAX8997_REG_LDO3CTRL, 0x6 | EN_LDO);
/* LDO4 voltage: 1.8v */
ret |= pmic_reg_write(p, MAX8997_REG_LDO4CTRL, 0x14 | EN_LDO);
if (ret) {
puts("MAX8997 LDO setting error!\n");
return -1;
}
return 0;
}
void exynos_lcd_misc_init(vidinfo_t *vid)
{
#ifdef CONFIG_TIZEN
get_tizen_logo_info(vid);
#endif
#ifdef CONFIG_S6E8AX0
s6e8ax0_init();
setenv("lcdinfo", "lcd=s6e8ax0");
#endif
}