mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-05 11:00:15 +00:00
e8272cbd59
The function arch_cpu_init_dm was renamed to fsp_setup_pinctrl in these
cases, so rename debug / docs to match.
Cc: Simon Glass <sjg@chromium.org>
Fixes: 7fe32b3442
("event: Convert arch_cpu_init_dm() to use events")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
442 lines
17 KiB
ReStructuredText
442 lines
17 KiB
ReStructuredText
.. SPDX-License-Identifier: GPL-2.0+
|
|
.. sectionauthor:: Simon Glass <sjg@chromium.org>
|
|
|
|
Chromebook Coral
|
|
================
|
|
|
|
Coral is a Chromebook (or really about 20 different Chromebooks) which use the
|
|
Intel Apollo Lake platform (APL). The 'reef' Chromebooks use the same APL SoC so
|
|
should also work. Some later ones based on Glacier Lake (GLK) need various
|
|
changes in GPIOs, etc. but are very similar.
|
|
|
|
It is hoped that this port can enable ports to embedded APL boards which are
|
|
starting to appear.
|
|
|
|
Note that booting U-Boot on APL is already supported by coreboot and
|
|
Slim Bootloader. This documentation refers to a 'bare metal' port.
|
|
|
|
|
|
Building
|
|
--------
|
|
|
|
First, you need the following binary blobs:
|
|
|
|
* descriptor.bin - Intel flash descriptor
|
|
* fitimage.bin - Base flash image structure
|
|
* fsp_m.bin - FSP-M, for setting up SDRAM
|
|
* fsp_s.bin - FSP-S, for setting up Silicon
|
|
* vbt.bin - for setting up display
|
|
|
|
These binaries do not seem to be available publicly. If you have a ROM image,
|
|
such as santa.bin then you can do this::
|
|
|
|
cbfstool santa.bin extract -n fspm.bin -f fsp-m.bin
|
|
cbfstool santa.bin extract -n fsps.bin -f fsp-s.bin
|
|
cbfstool santa.bin extract -n vbt-santa.bin -f vbt.bin
|
|
mkdir tmp
|
|
cd tmp
|
|
dump_fmap -x ../santa.bin
|
|
mv SI_DESC ../descriptor.bin
|
|
mv IFWI ../fitimage.bin
|
|
|
|
Put all of these files in `board/google/chromebook_coral` so they can be found
|
|
by the build.
|
|
|
|
To build::
|
|
|
|
make O=/tmp/b/chromebook_coral chromebook_coral_defconfig
|
|
make O=/tmp/b/chromebook_coral -s -j30 all
|
|
|
|
That should produce `/tmp/b/chrombook_coral/u-boot.rom` which you can use with
|
|
a Dediprog em100::
|
|
|
|
em100 -s -c w25q128fw -d /tmp/b/chromebook_coral/u-boot.rom -r
|
|
|
|
or you can use flashrom to write it to the board. If you do that, make sure you
|
|
have a way to restore the old ROM without booting the board. Otherwise you may
|
|
brick it. Having said that, you may find these instructions useful if you want
|
|
to unbrick your device:
|
|
|
|
https://chromium.googlesource.com/chromiumos/platform/ec/+/cr50_stab/docs/case_closed_debugging.md
|
|
|
|
You can buy Suzy-Q from Sparkfun:
|
|
|
|
https://chromium.googlesource.com/chromiumos/third_party/hdctools/+/main/docs/ccd.md#suzyq-suzyqable
|
|
|
|
Note that it will hang at the SPL prompt for 21 seconds. When booting into
|
|
Chrome OS it will always select developer mode, so will wipe anything you have
|
|
on the device if you let it proceed. You have two seconds in U-Boot to stop the
|
|
auto-boot prompt and several seconds at the 'developer wipe' screen to stop it
|
|
wiping the disk.
|
|
|
|
Here is the console output::
|
|
|
|
U-Boot TPL 2021.04-rc1-00128-g344eefcdfec-dirty (Feb 11 2021 - 20:13:08 -0700)
|
|
Trying to boot from Mapped SPI
|
|
|
|
U-Boot SPL 2021.04-rc1-00128-g344eefcdfec-dirty (Feb 11 2021 - 20:13:08 -0700)
|
|
Trying to boot from Mapped SPI
|
|
|
|
|
|
U-Boot 2021.04-rc1-00128-g344eefcdfec-dirty (Feb 11 2021 - 20:13:08 -0700)
|
|
|
|
CPU: Intel(R) Celeron(R) CPU N3450 @ 1.10GHz
|
|
DRAM: 3.9 GiB
|
|
MMC: sdmmc@1b,0: 1, emmc@1c,0: 2
|
|
Video: 1024x768x32 @ b0000000
|
|
Model: Google Coral
|
|
Net: No ethernet found.
|
|
SF: Detected w25q128fw with page size 256 Bytes, erase size 4 KiB, total 16 MiB
|
|
Hit any key to stop autoboot: 0
|
|
cmdline=console= loglevel=7 init=/sbin/init cros_secure oops=panic panic=-1 root=PARTUUID=${uuid}/PARTNROFF=1 rootwait rw dm_verity.error_behavior=3 dm_verity.max_bios=-1 dm_verity.dev_wait=0 dm="1 vroot none rw 1,0 3788800 verity payload=ROOT_DEV hashtree=HASH_DEV hashstart=3788800 alg=sha1 root_hexdigest=55052b629d3ac889f25a9583ea12cdcd3ea15ff8 salt=a2d4d9e574069f4fed5e3961b99054b7a4905414b60a25d89974a7334021165c" noinitrd vt.global_cursor_default=0 kern_guid=${uuid} add_efi_memmap boot=local noresume noswap i915.modeset=1 Kernel command line: "console= loglevel=7 init=/sbin/init cros_secure oops=panic panic=-1 root=PARTUUID=35c775e7-3735-d745-93e5-d9e0238f7ed0/PARTNROFF=1 rootwait rw dm_verity.error_behavior=3 dm_verity.max_bios=-1 dm_verity.dev_wait=0 dm="1 vroot none rw 1,0 3788800 verity payload=ROOT_DEV hashtree=HASH_DEV hashstart=3788800 alg=sha1 root_hexdigest=55052b629d3ac889f25a9583ea12cdcd3ea15ff8 salt=a2d4d9e574069f4fed5e3961b99054b7a4905414b60a25d89974a7334021165c" noinitrd vt.global_cursor_default=0 kern_guid=35c775e7-3735-d745-93e5-d9e0238f7ed0 add_efi_memmap boot=local noresume noswap i915.modeset=1 tpm_tis.force=1 tpm_tis.interrupts=0 nmi_watchdog=panic,lapic disablevmx=off "
|
|
Setup located at 00090000:
|
|
|
|
ACPI RSDP addr : 7991f000
|
|
E820: 14 entries
|
|
Addr Size Type
|
|
d0000000 1000000 <NULL>
|
|
0 a0000 RAM
|
|
a0000 60000 Reserved
|
|
7b000000 800000 Reserved
|
|
7b800000 4800000 Reserved
|
|
7ac00000 400000 Reserved
|
|
100000 ff00000 RAM
|
|
10000000 2151000 Reserved
|
|
12151000 68aaf000 RAM
|
|
100000000 80000000 RAM
|
|
e0000000 10000000 Reserved
|
|
7991bfd0 12e4030 Reserved
|
|
d0000000 10000000 Reserved
|
|
fed10000 8000 Reserved
|
|
Setup sectors : 1e
|
|
Root flags : 1
|
|
Sys size : 63420
|
|
RAM size : 0
|
|
Video mode : ffff
|
|
Root dev : 0
|
|
Boot flag : 0
|
|
Jump : 66eb
|
|
Header : 53726448
|
|
Kernel V2
|
|
Version : 20d
|
|
Real mode switch : 0
|
|
Start sys : 1000
|
|
Kernel version : 38cc
|
|
@00003acc:
|
|
Type of loader : 80
|
|
U-Boot, version 0
|
|
Load flags : 81
|
|
: loaded-high can-use-heap
|
|
Setup move size : 8000
|
|
Code32 start : 100000
|
|
Ramdisk image : 0
|
|
Ramdisk size : 0
|
|
Bootsect kludge : 0
|
|
Heap end ptr : 8e00
|
|
Ext loader ver : 0
|
|
Ext loader type : 0
|
|
Command line ptr : 99000
|
|
console= loglevel=7 init=/sbin/init cros_secure oops=panic panic=-1 root=PARTUUID=35c775e7-3735-d745-93e5-d9e0238f7ed0/PARTNROFF=1 rootwait rw dm_verity.error_behavior=3 dm_verity.max_bios=-1 dm_verity.dev_wait=0 dm="1 vroot none rw 1,0 3788800 verity payload=ROOT_DEV hashtree=HASH_DEV hashstart=3788800 alg=sha1 root_hexdigest=55052b629d3ac889f25a9583ea12cdcd3ea15ff8 salt=a2d4d9e574069f4fed5e3961b99054b7a4905414b60a25d89974a7334021165c" noinitrd vt.global_cursor_default=0 kern_guid=35c775e7-3735-d745-93e5-d9e0238f7ed0 add_efi_memmap boot=local noresume noswap i915.modeset=1 tpm_tis.force=1 tpm_tis.interrupts=0 nmi_watchdog=panic,lapic disablevmx=off
|
|
Initrd addr max : 7fffffff
|
|
Kernel alignment : 200000
|
|
Relocatable kernel : 1
|
|
Min alignment : 15
|
|
: 200000
|
|
Xload flags : 3
|
|
: 64-bit-entry can-load-above-4gb
|
|
Cmdline size : 7ff
|
|
Hardware subarch : 0
|
|
HW subarch data : 0
|
|
Payload offset : 26e
|
|
Payload length : 612045
|
|
Setup data : 0
|
|
Pref address : 1000000
|
|
Init size : 1383000
|
|
Handover offset : 0
|
|
|
|
Starting kernel ...
|
|
|
|
Timer summary in microseconds (17 records):
|
|
Mark Elapsed Stage
|
|
0 0 reset
|
|
155,279 155,279 TPL
|
|
237,088 81,809 end phase
|
|
237,533 445 SPL
|
|
816,456 578,923 end phase
|
|
817,357 901 board_init_f
|
|
1,061,751 244,394 board_init_r
|
|
1,402,435 340,684 id=64
|
|
1,430,071 27,636 main_loop
|
|
5,532,057 4,101,986 start_kernel
|
|
|
|
Accumulated time:
|
|
685 dm_r
|
|
2,817 fast_spi
|
|
33,095 dm_spl
|
|
52,468 dm_f
|
|
208,242 fsp-m
|
|
242,221 fsp-s
|
|
332,710 mmap_spi
|
|
|
|
|
|
Boot flow - TPL
|
|
---------------
|
|
|
|
Apollo Lake boots via an IFWI (Integrated Firmware Image). TPL is placed in
|
|
this, in the IBBL entry.
|
|
|
|
On boot, an on-chip microcontroller called the CSE (Converged Security Engine)
|
|
sets up some SDRAM at ffff8000 and loads the TPL image to that address. The
|
|
SRAM extends up to the top of 32-bit address space, but the last 2KB is the
|
|
start16 region, so the TPL image must be 30KB at most, and CONFIG_TPL_TEXT_BASE
|
|
must be ffff8000. Actually the start16 region is small and it could probably
|
|
move from f800 to fe00, providing another 1.5KB, but TPL is only about 19KB so
|
|
there is no need to change it at present. The size limit is enforced by
|
|
CONFIG_TPL_SIZE_LIMIT to avoid producing images that won't boot.
|
|
|
|
TPL (running from start.S) first sets up CAR (Cache-as-RAM) which provides
|
|
larger area of RAM for use while booting. CAR is mapped at CONFIG_SYS_CAR_ADDR
|
|
(fef00000) and is 768KB in size. It then sets up the stack in the botttom 64KB
|
|
of this space (i.e. below fef10000). This means that the stack and early
|
|
malloc() region in TPL can be 64KB at most.
|
|
|
|
TPL operates without CONFIG_TPL_PCI enabled so PCI config access must use the
|
|
x86-specific functions pci_x86_write_config(), etc. SPL creates a simple-bus
|
|
device so that PCI devices are bound by driver model. Then arch_cpu_init_tpl()
|
|
is called to early init on various devices. This includes placing PCI devices
|
|
at hard-coded addresses in the memory map. PCI auto-config is not used.
|
|
|
|
Most of the 16KB ROM is mapped into the very top of memory, except for the
|
|
Intel descriptor (first 4KB) and the space for SRAM as above.
|
|
|
|
TPL does not set up a bloblist since at present it does not have anything to
|
|
pass to SPL.
|
|
|
|
Once TPL is done it loads SPL from ROM using either the memory-mapped SPI or by
|
|
using the Intel fast SPI driver. SPL is loaded into CAR, at the address given
|
|
by CONFIG_SPL_TEXT_BASE, which is normally fef10000.
|
|
|
|
Note that booting using the SPI driver results in an TPL image that is about
|
|
26KB in size instead of 19KB. Also boot speed is worse by about 340ms. If you
|
|
really want to use the driver, enable CONFIG_APL_SPI_FLASH_BOOT and set
|
|
BOOT_FROM_FAST_SPI_FLASH to true[2].
|
|
|
|
|
|
Boot flow - SPL
|
|
---------------
|
|
|
|
SPL (running from start_from_tpl.S) continues to use the same stack as TPL.
|
|
It calls arch_cpu_init_spl() to set up a few devices, then init_dram() loads
|
|
the FSP-M binary into CAR and runs to, to set up SDRAM. The address of the
|
|
output 'HOB' list (Hand-off-block) is stored into gd->arch.hob_list for parsing.
|
|
There is a 2GB chunk of SDRAM starting at 0 and the rest is at 4GB.
|
|
|
|
PCI auto-config is not used in SPL either, but CONFIG_SPL_PCI is defined, so
|
|
proper PCI access is available and normal dm_pci_read_config() calls can be
|
|
used. However PCI auto-config is not used so the same static memory mapping set
|
|
up by TPL is still active.
|
|
|
|
SPL on x86 always runs with CONFIG_SPL_SEPARATE_BSS=y and BSS is at 120000
|
|
(see u-boot-spl.lds). This works because SPL doesn't access BSS until after
|
|
board_init_r(), as per the rules, and DRAM is available then.
|
|
|
|
SPL sets up a bloblist and passes the SPL hand-off information to U-Boot proper.
|
|
This includes a pointer to the HOB list as well as DRAM information. See
|
|
struct arch_spl_handoff. The bloblist address is set by CONFIG_BLOBLIST_ADDR,
|
|
normally 100000.
|
|
|
|
SPL uses SPI flash to update the MRC caches in ROM. This speeds up subsequent
|
|
boots. Be warned that SPL can take 30 seconds without this cache! This is a
|
|
known issue with Intel SoCs with modern DRAM and apparently cannot be improved.
|
|
The MRC caches are used to work around this.
|
|
|
|
Once SPL is finished it loads U-Boot into SDRAM at CONFIG_TEXT_BASE, which
|
|
is normally 1110000. Note that CAR is still active.
|
|
|
|
|
|
Boot flow - U-Boot pre-relocation
|
|
---------------------------------
|
|
|
|
U-Boot (running from start_from_spl.S) starts running in RAM and uses the same
|
|
stack as SPL. It does various init activities before relocation. Notably
|
|
fsp_setup_pinctrl() sets up the pin muxing for the chip using a very large table
|
|
in the device tree.
|
|
|
|
PCI auto-config is not used before relocation, but CONFIG_PCI of course is
|
|
defined, so proper PCI access is available. The same static memory mapping set
|
|
up by TPL is still active until relocation.
|
|
|
|
As per usual, U-Boot allocates memory at the top of available RAM (a bit below
|
|
2GB in this case) and copies things there ready to relocate itself. Notably
|
|
reserve_arch() does not reserve space for the HOB list returned by FSP-M since
|
|
this is already located in RAM.
|
|
|
|
U-Boot then shuts down CAR and jumps to its relocated version.
|
|
|
|
|
|
Boot flow - U-Boot post-relocation
|
|
----------------------------------
|
|
|
|
U-Boot starts up normally, running near the top of RAM. After driver model is
|
|
running, arch_fsp_init_r() is called which loads and runs the FSP-S binary.
|
|
This updates the HOB list to include graphics information, used by the fsp_video
|
|
driver.
|
|
|
|
PCI autoconfig is done and a few devices are probed to complete init. Most
|
|
others are started only when they are used.
|
|
|
|
Note that FSP-S is supposed to run after CAR has been shut down, which happens
|
|
immediately before U-Boot starts up in its relocated position. Therefore we
|
|
cannot run FSP-S before relocation. On the other hand we must run it before
|
|
PCI auto-config is done, since FSP-S may show or hide devices. The first device
|
|
that probes PCI after relocation is the serial port, in initr_serial(), so FSP-S
|
|
must run before that. A corollary is that loading FSP-S must be done without
|
|
using the SPI driver, to avoid probing PCI and causing an autoconfig, so
|
|
memory-mapped reading is always used for FSP-S.
|
|
|
|
It would be possible to tear down CAR in SPL instead of U-Boot. The SPL handoff
|
|
information could make sure it does not include any pointers into CAR (in fact
|
|
it doesn't). But tearing down CAR in U-Boot allows the initial state used by TPL
|
|
and SPL to be read by U-Boot, which seems useful. It also matches how older
|
|
platforms start up (those that don't use SPL).
|
|
|
|
|
|
Performance
|
|
-----------
|
|
|
|
Bootstage is used through all phases of U-Boot to keep accurate timimgs for
|
|
boot. Use 'bootstage report' in U-Boot to see the report, e.g.::
|
|
|
|
Timer summary in microseconds (16 records):
|
|
Mark Elapsed Stage
|
|
0 0 reset
|
|
155,325 155,325 TPL
|
|
204,014 48,689 end TPL
|
|
204,385 371 SPL
|
|
738,633 534,248 end SPL
|
|
739,161 528 board_init_f
|
|
842,764 103,603 board_init_r
|
|
1,166,233 323,469 main_loop
|
|
1,166,283 50 id=175
|
|
|
|
Accumulated time:
|
|
62 fast_spi
|
|
202 dm_r
|
|
7,779 dm_spl
|
|
15,555 dm_f
|
|
208,357 fsp-m
|
|
239,847 fsp-s
|
|
292,143 mmap_spi
|
|
|
|
CPU performance is about 3500 DMIPS::
|
|
|
|
=> dhry
|
|
1000000 iterations in 161 ms: 6211180/s, 3535 DMIPS
|
|
|
|
|
|
Partial memory map
|
|
------------------
|
|
|
|
::
|
|
|
|
ffffffff Top of ROM (and last byte of 32-bit address space)
|
|
ffff8000 TPL loaded here (from IFWI)
|
|
ff000000 Bottom of ROM
|
|
fefc0000 Top of CAR region
|
|
fef96000 Stack for FSP-M
|
|
fef40000 59000 FSP-M (also VPL loads here)
|
|
fef11000 SPL loaded here
|
|
fef10000 CONFIG_BLOBLIST_ADDR
|
|
fef10000 Stack top in TPL, SPL and U-Boot before relocation
|
|
fef00000 1000 CONFIG_BOOTSTAGE_STASH_ADDR
|
|
fef00000 Base of CAR region
|
|
|
|
30000 AP_DEFAULT_BASE (used to start up additional CPUs)
|
|
f0000 CONFIG_ROM_TABLE_ADDR
|
|
120000 BSS (defined in u-boot-spl.lds)
|
|
200000 FSP-S (which is run after U-Boot is relocated)
|
|
1110000 CONFIG_TEXT_BASE
|
|
|
|
|
|
Speeding up SPL for development
|
|
-------------------------------
|
|
|
|
The 21-second wait for memory training is annoying during development, since
|
|
every new image incurs this cost when booting. There is no cache to fall back on
|
|
since that area of the image is empty on start-up.
|
|
|
|
You can add suitable cache contents to the image to fix this, for development
|
|
purposes only, like this::
|
|
|
|
# Read the image back after booting through SPL
|
|
em100 -s -c w25q128fw -u image.bin
|
|
|
|
# Extract the two cache regions
|
|
binman extract -i image.bin extra *cache
|
|
|
|
# Move them into the source directory
|
|
mv *cache board/google/chromebook_coral
|
|
|
|
Then add something like this to the devicetree::
|
|
|
|
#if IS_ENABLED(CONFIG_HAVE_MRC) || IS_ENABLED(CONFIG_FSP_VERSION2)
|
|
/* Provide initial contents of the MRC data for faster development */
|
|
rw-mrc-cache {
|
|
type = "blob";
|
|
/* Mirror the offset in spi-flash@0 */
|
|
offset = <0xff8e0000>;
|
|
size = <0x10000>;
|
|
filename = "board/google/chromebook_coral/rw-mrc-cache";
|
|
};
|
|
rw-var-mrc-cache {
|
|
type = "blob";
|
|
size = <0x1000>;
|
|
filename = "board/google/chromebook_coral/rw-var-mrc-cache";
|
|
};
|
|
#endif
|
|
|
|
This tells binman to put the cache contents in the same place as the
|
|
`rw-mrc-cache` and `rw-var-mrc-cache` regions defined by the SPI-flash driver.
|
|
|
|
|
|
Supported peripherals
|
|
---------------------
|
|
|
|
The following have U-Boot drivers:
|
|
|
|
- UART
|
|
- SPI flash
|
|
- Video
|
|
- MMC (dev 0) and micro-SD (dev 1)
|
|
- Chrome OS EC
|
|
- Cr50 (security chip)
|
|
- Keyboard
|
|
- USB
|
|
|
|
|
|
To do
|
|
-----
|
|
|
|
- Finish peripherals
|
|
- Sound (Intel I2S support exists, but need da7219 driver)
|
|
- Use FSP-T binary instead of our own CAR implementation
|
|
- Use the official FSP package instead of the coreboot one
|
|
- Suspend / resume
|
|
- Fix MMC which seems to try to read even though the card is empty
|
|
- Fix USB3 crash "WARN halted endpoint, queueing URB anyway."
|
|
|
|
|
|
Credits
|
|
-------
|
|
|
|
This is a spare-time project conducted slowly over a long period of time.
|
|
|
|
Much of the code for this port came from Coreboot, an open-source firmware
|
|
project similar to U-Boot's SPL in terms of features.
|
|
|
|
Also see [2] for information about the boot flow used by coreboot. It is
|
|
similar, but has an extra postcar stage. U-Boot doesn't need this since it
|
|
supports relocating itself in memory.
|
|
|
|
|
|
[2] Intel PDF https://www.coreboot.org/images/2/23/Apollolake_SoC.pdf
|