mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-16 01:38:22 +00:00
fc8991c61c
cpu_eth_init is no longer called for dm enabled eth drivers, this was causing the sunxi gmac eth controller to no longer work in u-boot. This commit fixes this by calling the clock, reset and pinmux setup function from s_init() and enabling the phy power pin (if any) from board_init(). The enabling of phy power cannot be done from s_init because it uses dm and dm is not ready yet at this point. Note that the mdelay is dropped as the phy gets enabled much earlier now, so it is no longer needed. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Tested-by: Karsten Merker <merker@debian.org> Tested-by: Michael Haas <haas@computerlinguist.org>
82 lines
2.6 KiB
C
82 lines
2.6 KiB
C
#include <common.h>
|
|
#include <netdev.h>
|
|
#include <miiphy.h>
|
|
#include <asm/gpio.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/clock.h>
|
|
#include <asm/arch/gpio.h>
|
|
|
|
void eth_init_board(void)
|
|
{
|
|
int pin;
|
|
struct sunxi_ccm_reg *const ccm =
|
|
(struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
|
|
|
|
/* Set up clock gating */
|
|
#ifdef CONFIG_SUNXI_GEN_SUN6I
|
|
setbits_le32(&ccm->ahb_reset0_cfg, 0x1 << AHB_RESET_OFFSET_GMAC);
|
|
setbits_le32(&ccm->ahb_gate0, 0x1 << AHB_GATE_OFFSET_GMAC);
|
|
#else
|
|
setbits_le32(&ccm->ahb_gate1, 0x1 << AHB_GATE_OFFSET_GMAC);
|
|
#endif
|
|
|
|
/* Set MII clock */
|
|
#ifdef CONFIG_RGMII
|
|
setbits_le32(&ccm->gmac_clk_cfg, CCM_GMAC_CTRL_TX_CLK_SRC_INT_RGMII |
|
|
CCM_GMAC_CTRL_GPIT_RGMII);
|
|
setbits_le32(&ccm->gmac_clk_cfg,
|
|
CCM_GMAC_CTRL_TX_CLK_DELAY(CONFIG_GMAC_TX_DELAY));
|
|
#else
|
|
setbits_le32(&ccm->gmac_clk_cfg, CCM_GMAC_CTRL_TX_CLK_SRC_MII |
|
|
CCM_GMAC_CTRL_GPIT_MII);
|
|
#endif
|
|
|
|
#ifndef CONFIG_MACH_SUN6I
|
|
/* Configure pin mux settings for GMAC */
|
|
for (pin = SUNXI_GPA(0); pin <= SUNXI_GPA(16); pin++) {
|
|
#ifdef CONFIG_RGMII
|
|
/* skip unused pins in RGMII mode */
|
|
if (pin == SUNXI_GPA(9) || pin == SUNXI_GPA(14))
|
|
continue;
|
|
#endif
|
|
sunxi_gpio_set_cfgpin(pin, SUN7I_GPA_GMAC);
|
|
sunxi_gpio_set_drv(pin, 3);
|
|
}
|
|
#elif defined CONFIG_RGMII
|
|
/* Configure sun6i RGMII mode pin mux settings */
|
|
for (pin = SUNXI_GPA(0); pin <= SUNXI_GPA(3); pin++) {
|
|
sunxi_gpio_set_cfgpin(pin, SUN6I_GPA_GMAC);
|
|
sunxi_gpio_set_drv(pin, 3);
|
|
}
|
|
for (pin = SUNXI_GPA(9); pin <= SUNXI_GPA(14); pin++) {
|
|
sunxi_gpio_set_cfgpin(pin, SUN6I_GPA_GMAC);
|
|
sunxi_gpio_set_drv(pin, 3);
|
|
}
|
|
for (pin = SUNXI_GPA(19); pin <= SUNXI_GPA(20); pin++) {
|
|
sunxi_gpio_set_cfgpin(pin, SUN6I_GPA_GMAC);
|
|
sunxi_gpio_set_drv(pin, 3);
|
|
}
|
|
for (pin = SUNXI_GPA(25); pin <= SUNXI_GPA(27); pin++) {
|
|
sunxi_gpio_set_cfgpin(pin, SUN6I_GPA_GMAC);
|
|
sunxi_gpio_set_drv(pin, 3);
|
|
}
|
|
#elif defined CONFIG_GMII
|
|
/* Configure sun6i GMII mode pin mux settings */
|
|
for (pin = SUNXI_GPA(0); pin <= SUNXI_GPA(27); pin++) {
|
|
sunxi_gpio_set_cfgpin(pin, SUN6I_GPA_GMAC);
|
|
sunxi_gpio_set_drv(pin, 2);
|
|
}
|
|
#else
|
|
/* Configure sun6i MII mode pin mux settings */
|
|
for (pin = SUNXI_GPA(0); pin <= SUNXI_GPA(3); pin++)
|
|
sunxi_gpio_set_cfgpin(pin, SUN6I_GPA_GMAC);
|
|
for (pin = SUNXI_GPA(8); pin <= SUNXI_GPA(9); pin++)
|
|
sunxi_gpio_set_cfgpin(pin, SUN6I_GPA_GMAC);
|
|
for (pin = SUNXI_GPA(11); pin <= SUNXI_GPA(14); pin++)
|
|
sunxi_gpio_set_cfgpin(pin, SUN6I_GPA_GMAC);
|
|
for (pin = SUNXI_GPA(19); pin <= SUNXI_GPA(24); pin++)
|
|
sunxi_gpio_set_cfgpin(pin, SUN6I_GPA_GMAC);
|
|
for (pin = SUNXI_GPA(26); pin <= SUNXI_GPA(27); pin++)
|
|
sunxi_gpio_set_cfgpin(pin, SUN6I_GPA_GMAC);
|
|
#endif
|
|
}
|