mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-17 08:43:07 +00:00
a3a0bc85c0
CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 49C Reset cause: POR Model: Seeed NPi iMX6ULL Dev Board with NAND Board: Seeed NPi i.MX6ULL Dev Board DRAM: 512 MiB NAND: 512 MiB MMC: FSL_SDHC: 0 In: serial@2020000 Out: serial@2020000 Err: serial@2020000 Net: FEC0 Working: - Eth0 - MMC/SD - NAND - UART 1 - USB host Signed-off-by: Navin Sankar Velliangiri <navin@linumiz.com> Note: Changes in v2: * removed unnecessary space in imx6ull-seeed-npi-imx6ull-dev-board.dts file. * Used SZ_2M for CONFIG_SYS_MALLOC_LEN size allocation.
114 lines
2.2 KiB
C
114 lines
2.2 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright (c) 2021 Linumiz
|
|
* Author: Navin Sankar Velliangiri <navin@linumiz.com>
|
|
*/
|
|
|
|
#include <init.h>
|
|
#include <asm/arch/clock.h>
|
|
#include <asm/arch/crm_regs.h>
|
|
#include <asm/arch/iomux.h>
|
|
#include <asm/arch/mx6-pins.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <asm/mach-imx/iomux-v3.h>
|
|
#include <asm/mach-imx/mxc_i2c.h>
|
|
#include <fsl_esdhc_imx.h>
|
|
#include <linux/bitops.h>
|
|
#include <miiphy.h>
|
|
#include <net.h>
|
|
#include <netdev.h>
|
|
#include <usb.h>
|
|
#include <usb/ehci-ci.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
int dram_init(void)
|
|
{
|
|
gd->ram_size = imx_ddr_size();
|
|
|
|
return 0;
|
|
}
|
|
|
|
#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
|
|
PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
|
|
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | \
|
|
PAD_CTL_HYS)
|
|
|
|
static iomux_v3_cfg_t const uart1_pads[] = {
|
|
MX6_PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
|
|
MX6_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
|
|
};
|
|
|
|
static void setup_iomux_uart(void)
|
|
{
|
|
imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
|
|
}
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
setup_iomux_uart();
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_FEC_MXC
|
|
|
|
static int setup_fec(int fec_id)
|
|
{
|
|
struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
|
|
int ret;
|
|
|
|
if (fec_id == 0) {
|
|
/*
|
|
* Use 50MHz anatop loopback REF_CLK1 for ENET1,
|
|
* clear gpr1[13], set gpr1[17].
|
|
*/
|
|
clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC1_MASK,
|
|
IOMUX_GPR1_FEC1_CLOCK_MUX1_SEL_MASK);
|
|
} else {
|
|
/*
|
|
* Use 50MHz anatop loopbak REF_CLK2 for ENET2,
|
|
* clear gpr1[14], set gpr1[18].
|
|
*/
|
|
clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC2_MASK,
|
|
IOMUX_GPR1_FEC2_CLOCK_MUX1_SEL_MASK);
|
|
}
|
|
|
|
ret = enable_fec_anatop_clock(fec_id, ENET_50MHZ);
|
|
if (ret)
|
|
return ret;
|
|
|
|
enable_enet_clk(1);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_phy_config(struct phy_device *phydev)
|
|
{
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0x1f, 0x8190);
|
|
|
|
if (phydev->drv->config)
|
|
phydev->drv->config(phydev);
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
int board_init(void)
|
|
{
|
|
/* Address of boot parameters */
|
|
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
|
|
|
|
#ifdef CONFIG_FEC_MXC
|
|
setup_fec(CONFIG_FEC_ENET_DEV);
|
|
#endif
|
|
|
|
return 0;
|
|
}
|
|
|
|
int checkboard(void)
|
|
{
|
|
printf("Board: Seeed NPi i.MX6ULL Dev Board\n");
|
|
|
|
return 0;
|
|
}
|