mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-05 02:51:00 +00:00
a5752f8a25
This converts the following to Kconfig: CONFIG_SYS_I2C_SPEED CONFIG_SYS_I2C_SLAVE Signed-off-by: Tom Rini <trini@konsulko.com>
99 lines
2.8 KiB
C
99 lines
2.8 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* (C) Copyright 2011
|
|
* Marvell Semiconductor <www.marvell.com>
|
|
* Written-by: Lei Wen <leiwen@marvell.com>
|
|
*/
|
|
|
|
/*
|
|
* This file should be included in board config header file.
|
|
*
|
|
* It supports common definitions for Kirkwood platform
|
|
*/
|
|
|
|
#ifndef _KW_CONFIG_H
|
|
#define _KW_CONFIG_H
|
|
|
|
#if defined (CONFIG_KW88F6281)
|
|
#include <asm/arch/kw88f6281.h>
|
|
#elif defined (CONFIG_KW88F6192)
|
|
#include <asm/arch/kw88f6192.h>
|
|
#else
|
|
#error "SOC Name not defined"
|
|
#endif /* CONFIG_KW88F6281 */
|
|
|
|
#include <asm/arch/soc.h>
|
|
#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
|
|
#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
|
|
#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 for kernel */
|
|
|
|
/*
|
|
* By default kwbimage.cfg from board specific folder is used
|
|
* If for some board, different configuration file need to be used,
|
|
* CONFIG_SYS_KWD_CONFIG should be defined in board specific header file
|
|
*/
|
|
#ifndef CONFIG_SYS_KWD_CONFIG
|
|
#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg
|
|
#endif /* CONFIG_SYS_KWD_CONFIG */
|
|
|
|
/* Kirkwood has 2k of Security SRAM, use it for SP */
|
|
#define CONFIG_SYS_INIT_SP_ADDR 0xC8012000
|
|
|
|
#define CONFIG_I2C_MVTWSI_BASE0 KW_TWSI_BASE
|
|
#define MV_UART_CONSOLE_BASE KW_UART0_BASE
|
|
#define MV_SATA_BASE KW_SATA_BASE
|
|
#define MV_SATA_PORT0_OFFSET KW_SATA_PORT0_OFFSET
|
|
#define MV_SATA_PORT1_OFFSET KW_SATA_PORT1_OFFSET
|
|
|
|
/*
|
|
* NAND configuration
|
|
*/
|
|
#ifdef CONFIG_CMD_NAND
|
|
#define CONFIG_NAND_KIRKWOOD
|
|
#define CONFIG_SYS_NAND_BASE 0xD8000000 /* MV_DEFADR_NANDF */
|
|
#define NAND_ALLOW_ERASE_ALL 1
|
|
#endif
|
|
|
|
/*
|
|
* Ethernet Driver configuration
|
|
*/
|
|
#ifdef CONFIG_CMD_NET
|
|
#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */
|
|
#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */
|
|
#endif /* CONFIG_CMD_NET */
|
|
|
|
/*
|
|
* USB/EHCI
|
|
*/
|
|
#ifdef CONFIG_CMD_USB
|
|
#define CONFIG_EHCI_IS_TDI
|
|
#endif /* CONFIG_CMD_USB */
|
|
|
|
/*
|
|
* IDE Support on SATA ports
|
|
*/
|
|
#ifdef CONFIG_IDE
|
|
#define __io
|
|
/* Needs byte-swapping for ATA data register */
|
|
#define CONFIG_IDE_SWAP_IO
|
|
/* Data, registers and alternate blocks are at the same offset */
|
|
#define CONFIG_SYS_ATA_DATA_OFFSET (0x0100)
|
|
#define CONFIG_SYS_ATA_REG_OFFSET (0x0100)
|
|
#define CONFIG_SYS_ATA_ALT_OFFSET (0x0100)
|
|
/* Each 8-bit ATA register is aligned to a 4-bytes address */
|
|
#define CONFIG_SYS_ATA_STRIDE 4
|
|
/* Controller supports 48-bits LBA addressing */
|
|
#define CONFIG_LBA48
|
|
/* CONFIG_IDE requires some #defines for ATA registers */
|
|
#define CONFIG_SYS_IDE_MAXBUS 2
|
|
#define CONFIG_SYS_IDE_MAXDEVICE 2
|
|
/* ATA registers base is at SATA controller base */
|
|
#define CONFIG_SYS_ATA_BASE_ADDR MV_SATA_BASE
|
|
#endif /* CONFIG_IDE */
|
|
|
|
/* Use common timer */
|
|
#define CONFIG_SYS_TIMER_COUNTS_DOWN
|
|
#define CONFIG_SYS_TIMER_COUNTER (MVEBU_TIMER_BASE + 0x14)
|
|
#define CONFIG_SYS_TIMER_RATE CONFIG_SYS_TCLK
|
|
|
|
#endif /* _KW_CONFIG_H */
|