mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-14 08:57:58 +00:00
49e946cb6a
Debug trace buffers are memory mapped in DCSR space beyond 4M. Signed-off-by: Stephen George <stephen.george@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
122 lines
4.9 KiB
Text
122 lines
4.9 KiB
Text
Overview
|
|
--------
|
|
The T4240QDS is a high-performance computing evaluation, development and test
|
|
platform supporting the T4240 QorIQ™ Power Architecture™ processor. T4240QDS is
|
|
optimized to support the high-bandwidth DDR3 memory ports, as well as the
|
|
highly-configurable SerDes ports. The system is lead-free and RoHS-compliant.
|
|
|
|
Board Features
|
|
SERDES Connections
|
|
32 lanes grouped into four 8-lane banks
|
|
Two “front side” banks dedicated to Ethernet
|
|
- High-speed crosspoint switch fabric on selected lanes
|
|
- Two PCI Express slots with side-band connector supporting
|
|
- SGMII
|
|
- XAUI
|
|
- HiGig
|
|
- I-pass connectors allow board-to-board and loopback support
|
|
Two “back side” banks dedicated to other protocols
|
|
- High-speed crosspoint switch fabric on all lanes
|
|
- Four PCI Express slots with side-band connector supporting
|
|
- PCI Express 3.0
|
|
- SATA 2.0
|
|
- SRIO 2.0
|
|
- Supports 4X Aurora debug with two connectors
|
|
DDR Controllers
|
|
Three independant 64-bit DDR3 controllers
|
|
Supports rates of 1866 up to 2133 MHz data-rate
|
|
Supports two DDR3/DDR3LP UDIMM/RDIMMs per controller
|
|
DDR power supplies 1.5V to all devices with automatic tracking of VTT.
|
|
Power software-switchable to 1.35V if software detects all DDR3LP devices.
|
|
MT9JSF25672AZ-2G1KZESZF has been tested at 1333, 1600, 1867, 2000 and
|
|
2133MT/s speeds. For 1867MT/s and above, read-to-write turnaround time
|
|
increases by 1 clock.
|
|
|
|
IFC/Local Bus
|
|
NAND flash: 8-bit, async or sync, up to 2GB.
|
|
NOR: 16-bit, Address/Data Multiplexed (ADM), up to 128 MB
|
|
NOR: 8-bit or 16-bit, non-multiplexed, up to 512MB
|
|
- NOR devices support 16 virtual banks
|
|
GASIC: Minimal target within Qixis FPGA
|
|
PromJET rapid memory download support
|
|
Address demultiplexing handled within FPGA.
|
|
- Flexible demux allows 8 or 16 bit evaluation.
|
|
IFC Debug/Development card
|
|
- Support for 32-bit devices
|
|
Ethernet
|
|
Support two on-board RGMII 10/100/1G ethernet ports.
|
|
SGMII and XAUI support via SERDES block (see above).
|
|
1588 support via Symmetricom board.
|
|
QIXIS System Logic FPGA
|
|
Manages system power and reset sequencing
|
|
Manages DUT, board, clock, etc. configuration for dynamic shmoo
|
|
Collects V-I-T data in background for code/power profiling.
|
|
Supports legacy TMT test features (POSt, IRS, SYSCLK-synchronous assertion)
|
|
General fault monitoring and logging
|
|
Runs from ATX “hot” power rails allowing operation while system is off.
|
|
Clocks
|
|
System and DDR clock (SYSCLK, “DDRCLK”)
|
|
- Switch selectable to one of 16 common settings in the interval 33MHz-166MHz.
|
|
- Software selectable in 1MHz increments from 1-200MHz.
|
|
SERDES clocks
|
|
- Provides clocks to all SerDes blocks and slots
|
|
- 100, 125 and 156.25 MHz
|
|
Power Supplies
|
|
Dedicated regulators for VDD
|
|
- Adjustable from (0.7V to 1.3V at 80A
|
|
- Regulators can be controlled by VID and/or software
|
|
Dedicated regulator for GVDD_PL: 1.35/1.5V at 22A
|
|
- VTT/MVREF automatically track operating voltage
|
|
Dedicated regulators/filters for AVDD supplies
|
|
Dedicated regulators for other supplies: OVDD, BVDD, DVDD, LVDD, POVDD, etc.
|
|
USB
|
|
Supports two USB 2.0 ports with integrated PHYs
|
|
- One type A, one type micro-AB with 1.0A power per port.
|
|
Other IO
|
|
eSDHC/MMC
|
|
- SDHC card slot
|
|
eSPI port
|
|
- High-speed serial flash
|
|
Two Serial port
|
|
Four I2C ports
|
|
|
|
Memory map
|
|
----------
|
|
The addresses in brackets are physical addresses.
|
|
|
|
0x0_0000_0000 (0x0_0000_0000) - 0x0_7fff_ffff 2GB DDR (more than 2GB is initialized but not mapped under with TLB)
|
|
0x0_8000_0000 (0xc_0000_0000) - 0x0_dfff_ffff 1.5GB PCIE memory
|
|
0x0_f000_0000 (0xf_0000_0000) - 0x0_f1ff_ffff 32MB DCSR (includes trace buffers)
|
|
0x0_f400_0000 (0xf_f400_0000) - 0x0_f5ff_ffff 32MB BMan
|
|
0x0_f600_0000 (0xf_f600_0000) - 0x0_f7ff_ffff 32MB QMan
|
|
0x0_f800_0000 (0xf_f800_0000) - 0x0_f803_ffff 256KB PCIE IO
|
|
0x0_e000_0000 (0xf_e000_0000) - 0x0_efff_ffff 256MB NOR flash
|
|
0x0_fe00_0000 (0xf_fe00_0000) - 0x0_feff_ffff 16MB CCSR
|
|
0x0_ffdf_0000 (0xf_ffdf_0000) - 0x0_ffdf_03ff 4KB QIXIS
|
|
0x0_ffff_f000 (0x0_7fff_fff0) - 0x0_ffff_ffff 4KB Boot page translation for secondary cores
|
|
|
|
The physical address of the last (boot page translation) varies with the actual DDR size.
|
|
|
|
Voltage ID and VDD override
|
|
--------------------
|
|
T4240 has a VID feature. U-boot reads the VID efuses and adjust the voltage
|
|
accordingly. The voltage can also be override by command vdd_override. The
|
|
syntax is
|
|
|
|
vdd_override <voltage in mV>, eg. 1050 is for 1.050v.
|
|
|
|
Upon success, the actual voltage will be read back. The value is checked
|
|
for safety and any invalid value will not adjust the voltage.
|
|
|
|
Another way to override VDD is to use environmental variable, in case of using
|
|
command is too late for some debugging. The syntax is
|
|
|
|
setenv t4240qds_vdd_mv <voltage in mV>
|
|
saveenv
|
|
reset
|
|
|
|
The override voltage takes effect when booting.
|
|
|
|
Note: voltage adjustment needs to be done step by step. Changing voltage too
|
|
rapidly may cause current surge. The voltage stepping is done by software.
|
|
Users can set the final voltage directly.
|