u-boot/configs/ls1012ardb_tfa_defconfig
Yangbo Lu edb558c78f configs: disable eMMC HS200 support on layerscape platforms
The eMMC HS200 speed mode on Layerscape platforms has not been
supported properly. The eSDHC clock tuning has not been implemented
by now. So disable it until it is supported properly in case of
any potential issues.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-03-30 08:12:13 +05:30

65 lines
1.5 KiB
Text

CONFIG_ARM=y
CONFIG_TARGET_LS1012ARDB=y
CONFIG_TFABOOT=y
CONFIG_SYS_TEXT_BASE=0x82000000
CONFIG_ENV_SIZE=0x40000
CONFIG_ENV_SECT_SIZE=0x40000
CONFIG_ENV_OFFSET=0x500000
CONFIG_DM_GPIO=y
CONFIG_QSPI_AHB_INIT=y
CONFIG_NR_DRAM_BANKS=2
CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT=y
CONFIG_SEC_FIRMWARE_ARMV8_PSCI=y
CONFIG_AHCI=y
CONFIG_DISTRO_DEFAULTS=y
# CONFIG_SYS_MALLOC_F is not set
CONFIG_FIT_VERBOSE=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_OF_STDOUT_VIA_ALIAS=y
CONFIG_BOOTDELAY=10
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 quiet lpj=250000"
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_DISPLAY_BOARDINFO_LATE=y
CONFIG_CMD_GREPENV=y
CONFIG_CMD_MEMTEST=y
CONFIG_CMD_GPT=y
CONFIG_CMD_I2C=y
CONFIG_CMD_MMC=y
CONFIG_CMD_PCI=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_CACHE=y
CONFIG_OF_CONTROL=y
CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1012a-rdb"
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_ENV_ADDR=0x40500000
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA_CEVA=y
CONFIG_DM_I2C=y
CONFIG_DM_MMC=y
CONFIG_FSL_ESDHC=y
CONFIG_MTD=y
CONFIG_DM_SPI_FLASH=y
# CONFIG_SPI_FLASH_BAR is not set
# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
CONFIG_FSL_PFE=y
CONFIG_DM_ETH=y
CONFIG_E1000=y
CONFIG_PCI=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_LAYERSCAPE=y
CONFIG_DM_RTC=y
CONFIG_DM_SCSI=y
CONFIG_SYS_NS16550=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
CONFIG_FSL_DSPI=y
CONFIG_FSL_QSPI=y
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_USB_XHCI_HCD=y
CONFIG_USB_XHCI_DWC3=y