u-boot/include/configs/lsxl.h
Tom Rini a09fea1d28 env: Finish migration of common ENV options
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00

135 lines
3.9 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (c) 2012 Michael Walle
* Michael Walle <michael@walle.cc>
*/
#ifndef _CONFIG_LSXL_H
#define _CONFIG_LSXL_H
/*
* Version number information
*/
#if defined(CONFIG_LSCHLV2)
#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage-lschl.cfg
#define CONFIG_MACH_TYPE 3006
#define CONFIG_SYS_TCLK 166666667 /* 166 MHz */
#elif defined(CONFIG_LSXHL)
#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage-lsxhl.cfg
#define CONFIG_MACH_TYPE 2663
/* CONFIG_SYS_TCLK is 200000000 by default */
#else
#error "unknown board"
#endif
/*
* General configuration options
*/
#define CONFIG_FEROCEON_88FR131 /* CPU Core subversion */
#define CONFIG_KW88F6281 /* SOC Name */
#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
#define CONFIG_KIRKWOOD_GPIO
/*
* Commands configuration
*/
/*
* mv-common.h should be defined after CMD configs since it used them
* to enable certain macros
*/
#include "mv-common.h"
/* loading initramfs images without uimage header */
/*
* Environment variables configurations
*/
#ifdef CONFIG_SPI_FLASH
#define CONFIG_SYS_MAX_FLASH_BANKS 1
#define CONFIG_SYS_MAX_FLASH_SECT 8
#endif
/*
* Default environment variables
*/
#define CONFIG_LOADADDR 0x00800000
#if defined(CONFIG_LSXHL)
#define CONFIG_FDTFILE "kirkwood-lsxhl.dtb"
#elif defined(CONFIG_LSCHLV2)
#define CONFIG_FDTFILE "kirkwood-lschlv2.dtb"
#else
#error "Unsupported board"
#endif
#define CONFIG_EXTRA_ENV_SETTINGS \
"bootsource=legacy\0" \
"hdpart=0:1\0" \
"kernel_addr=0x00800000\0" \
"ramdisk_addr=0x01000000\0" \
"fdt_addr=0x00ff0000\0" \
"bootcmd_legacy=sata init " \
"&& load sata ${hdpart} ${kernel_addr} /uImage.buffalo "\
"&& load sata ${hdpart} ${ramdisk_addr} /initrd.buffalo "\
"&& bootm ${kernel_addr} ${ramdisk_addr}\0" \
"bootcmd_net=bootp ${kernel_addr} vmlinuz " \
"&& tftpboot ${ramdisk_addr} initrd.img " \
"&& setenv ramdisk_len ${filesize} " \
"&& tftpboot ${fdt_addr} " CONFIG_FDTFILE " " \
"&& bootz ${kernel_addr} " \
"${ramdisk_addr}:${ramdisk_len} ${fdt_addr}\0" \
"bootcmd_hdd=sata init " \
"&& load sata ${hdpart} ${kernel_addr} /vmlinuz " \
"&& load sata ${hdpart} ${ramdisk_addr} /initrd.img " \
"&& setenv ramdisk_len ${filesize} " \
"&& load sata ${hdpart} ${fdt_addr} /dtb " \
"&& bootz ${kernel_addr} " \
"${ramdisk_addr}:${ramdisk_len} ${fdt_addr}\0" \
"bootcmd_usb=usb start " \
"&& load usb 0:1 ${kernel_addr} /vmlinuz " \
"&& load usb 0:1 ${ramdisk_addr} /initrd.img " \
"&& setenv ramdisk_len ${filesize} " \
"&& load usb 0:1 ${fdt_addr} " CONFIG_FDTFILE " " \
"&& bootz ${kernel_addr} " \
"${ramdisk_addr}:${ramdisk_len} ${fdt_addr}\0" \
"bootcmd_rescue=run config_nc_dhcp; run nc\0" \
"eraseenv=sf probe 0 " \
"&& sf erase " __stringify(CONFIG_ENV_OFFSET) \
" +" __stringify(CONFIG_ENV_SIZE) "\0" \
"config_nc_dhcp=setenv autoload_old ${autoload}; " \
"setenv autoload no " \
"&& bootp " \
"&& setenv ncip " \
"&& setenv autoload ${autoload_old}; " \
"setenv autoload_old\0" \
"standard_env=setenv ipaddr; setenv netmask; setenv serverip; " \
"setenv ncip; setenv gatewayip; setenv ethact; " \
"setenv bootfile; setenv dnsip; " \
"setenv bootsource legacy; run ser\0" \
"restore_env=run standard_env; saveenv; reset\0" \
"ser=setenv stdin serial; setenv stdout serial; " \
"setenv stderr serial\0" \
"nc=setenv stdin nc; setenv stdout nc; setenv stderr nc\0" \
"stdin=serial\0" \
"stdout=serial\0" \
"stderr=serial\0"
/*
* Ethernet Driver configuration
*/
#ifdef CONFIG_CMD_NET
#define CONFIG_MVGBE_PORTS {0, 1} /* enable port 1 only */
#define CONFIG_PHY_BASE_ADR 7
#undef CONFIG_RESET_PHY_R
#endif /* CONFIG_CMD_NET */
#ifdef CONFIG_SATA
#define CONFIG_SYS_SATA_MAX_DEVICE 1
#define CONFIG_SYS_64BIT_LBA
#define CONFIG_LBA48
#endif
#endif /* _CONFIG_LSXL_H */